Hyundai Santa Fe (2006 year). Manual — part 25
AT -52
AUTOMATIC TRANSAXLE (F4A51)
C08
1
3
4
* *
*
7
8
9
10
1. D Range
3. P Range
4. N Range
7. R Range
8. Power supply IG1
9. Starting circuit
10. Starting circuit
SCMAT6701L
4)
Is voltage within specifications?
YES
▶ Go to "Signal circuit inspection" procedure.
NO
▶ Check that Fuse 10A is installed or not blown.
▶ Check for open in harness. Repair as necessary and go to "Verification of vehicle repair" procedure.
SIGNAL CIRCUIT INSPECTION
E2609BDA
1.
Ignition "OFF".
2.
Disconnect "TRANSAXLE RANGE SWITCH" and "TCM(PCM)" connector.
3.
Measure resistance between each terminal of the sensor harness connector and TCM(PCM) harness connector as
below.
Specification :
Pin No of "TRANSAXLE RANGE SWITCH"
C08 No.1
C08 No.3
C08 No.4
C08 No.7
Pin No of "PCM" harness
C30-A No.6
C30-A No.3
C30-A No.5
C30-A No.4
Specification
0Ω
0Ω
0Ω
0Ω
AUTOMATIC TRANSAXLE SYSTEM
AT -53
C08
1
3
4
* *
*
7
8
9
10
Ω
3. P Range
4. R Range
5. N Range
6. D Range
1. D Range
2. P Range
4. N Range
7. R Range
8. Power supply IG1
9. Staring circuit
10. Starting circuit
C30-A
*
*
*
* *
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
*
20
40
60 59 58
78
57
55 54 53
73 72 71 70 69
52 51
49 48 47
45 44 43 42 41
66 65
67
64 63 62 61
39 38
33 32
10 9
27 26 25
23
21
8
7
6
5
4
3
2
1
18
16 15
13
SCMAT6702L
4.
Is resistance within specifications?
YES
▶ Go to "Component inspection" procedure.
NO
▶ Check for Open in harness. Repair as necessary and Go to "Verification of Vehicle Repair" procedure.
COMPONENT INSPECTION
EFFA7D74
1.
Ignition "OFF".
2.
Remove "TRANSAXLE RANGE SWITCH".
3.
Measure the resistance between each terminal of the sensor.
Specification : Approx. 0 Ω
AT -54
AUTOMATIC TRANSAXLE (F4A51)
1
*
7
8
9
10
1. D Range
3. P Range
4. N Range
7. R Range
8. Power supply IG1
9. Starting circuit
10. Starting circuit
Ω
3 4
* *
C08
[ RANGE SWITCH continuity check table (Case of SPORTS MODE vehicle has no 3,2,L range) ]
Range
P
R
N
D
Terminal
3
2
L
1
2
3
4
5
6
7
8
9
10
Component side
SCMAT6703L
4.
Is resistance within specifications?
YES
▶ Substitute with a known-good PCM/TCM and check for proper operation. If the problem is corrected, replace
PCM/TCM as necessary and then go to "Verification of Vehicle Repair" procedure.
NO
▶ Replace "TRANSAXLE RANGE SWITCH" as necessary and Go to "Verification of Vehicle Repair" procedure.
VERIFICATION OF VEHICLE REPAIR
EB7F7EB6
After a repair, it is essential to verify that the fault has been corrected.
1.
Connect scantool and select "Diagnostic Trouble Codes(DTCs)" mode.
2.
Using a scantool, Clear DTC.
3.
Operate the vehicle within DTC Enable conditions in General information.
4.
Are any DTCs present?
YES
▶ Go to the applicable troubleshooting procedure.
NO
▶ System performing to specification at this time.
AUTOMATIC TRANSAXLE SYSTEM
AT -55
DTC P0708 TRANSAXLE RANGE SWITCH - HIGH INPUT
COMPONENT LOCATION
E8ECC177
Refer to DTC P0707.
GENERAL DESCRIPTION
E7E46C8A
Refer to DTC P0707.
DTC DESCRIPTION
ED5D0931
The TCM sets this code when the Transaxle Range Switch outputs multiple signals for more than 30 seconds.
DTC DETECTING CONDITION
EEFC7EC9
Item
Detecting Condition
Possible cause
DTC Strategy
• Check for multiful signals
Enable Conditions
• Engine state = "RUN"
• 11V ≤ Battery Voltage ≤ 16V
• TPS ≥ 3 %
Threshold value
• Multiple signal
Diagnostic Time
• More than 30sec
Fail Safe
• Recognition as previous signal
-
When signal is input "D" and "N" at the same
time, TCM regards it as "N" RANGE
-
After PCM/TCM Reset, If the if the PCM/TCM
detects multiple signal or no signal, then
it holds the 3rd gear position
• Open or short in
TRANSAXLE RANGE
SWITCH
• Faulty Shift cable adjustment
• Faulty Inhibitor switch
and Manual control lever
position adjustment
• Faulty TRANSAXLE RANGE
SWITCH
• Faulty PCM
SIGNAL WAVEFORM
E9A9AA09
Refer to DTC P0707.
MONITOR SCANTOOL DATA
ECBB7BFE
Refer to DTC P0707.
TERMINAL & CONNECTOR INSPECTION
EA22C7FA
Refer to DTC P0707.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст