Hyundai Santa Fe (2006 year). Manual — part 185
SUNROOF
BE -201
CIRCUIT DIAGRAM
E3BAFCEA
SUNROOF MOTOR & CONTROLLER
Power
input
Switch
Signal
SUNROOF SWITCH
Ground
Battery(+)
Controller
Hall sensor
Motor control
M
3
IG2
B(+)
Ground
Ground
OPEN
TILT UP
TILT DOWN
SLIDE CLOSE
TILT UP
SLIDE OPEN
CLOSE/TILT DOWN
6
1
8
-
2
5
10
4
-
1
2
3
4
5
6
7
8
9
10
(
MOTOR
)
(MAP LAMP)
1 2
2
3
2
1
1
4
3 4
SCMBE6421L
BE -202
BODY ELECTRICAL SYSTEM
SUNROOF SWITCH
INSPECTION
E3FE5982
1.
Disconnect the negative (-) battery terminal.
2.
Open the sunglass case cover from the overhead con-
sole then remove the 2 screws holding the overhead
console. Disconnect the switch connector (4P) and
Map lamp connector (2P), and then remove the over-
head console lamp.
SCMBE6422D
3.
Check for continuity between the terminals. If the con-
tinuity is not as specified, replace the sunroof switch.
[Switch side connector]
1
2
3
4
SCMBE6423L
SLIDE OPEN
CLOSE/DOWN
TILT UP
1
2
4
3
Terminal
Position
SCMBE6424L
SUNROOF
BE -203
SUNROOF MOTOR
REPLACEMENT
E7FAABC1
1.
Disconnect the negative (-) battery terminal.
2.
Remove the overhead console then remove the sun
roof motor mounting screws (3EA). And then remove
the sunroof motor after disconnecting the connector
(10 Pin).
1
2
3
4
5
6
7
8
9 10
SCMBE6425D
3.
Ground the terminals as below table, and check that
the sunroof unit operates as below table.
SLIDE OPEN
SLIDE CLOSE/DOWN
TILT UP
3
4
10
5
Terminal
Position
ETQF965A
4.
Make these input tests at the connector
if any test indicates a problem, find and correct the
cause, then recheck the system.
If all the input tests prove OK, the sunroof motor must
be faulty; replace it.
Termi-
nal
Test
condition
Test : Desired result
3
IG2 ON
Check for voltage to ground :
There should be battery voltage
1
Under all
conditions
Check for continuity to ground :
There should be continuity.
6
Under all
conditions
Check for voltage to ground :
There should be battery voltage.
RESETTING THE SUNROOF
Whenever the vehicle battery is disconnected or dis-
charged, or you use the emergency handle to operate the
sunroof, you have to reset your sunroof system as follows
:
1.
Turn the ignition key to the ON position.
2.
According to the position of the sunroof, do as follows.
1)
In case that the sunroof has closed completely or
been tilted :
Press the TILT button until the sunroof has tilted
upward completely.
2)
In case that the sunroof has slide-opened :
Press and hold the CLOSE button for more than 5
seconds until the sunroof has closed completely.
Press and hold the CLOSE button for more than 5
seconds after the sunroof has closed completely.
Press the TILT button until the sunroof has tilted
upward completely.
3.
Release the TILT button.
4.
Press and hold the TILT button once again until the
sunroof has returned to the original position of TILT
after it is raised a little higher than the maximum TILT
position.
When this is complete, the sunroof system is reset.
BE -204
BODY ELECTRICAL SYSTEM
LIGHTING SYSTEM
SPECIFICATION
E46B93B3
Items
Bulb Wattage (W)
Head lamp (High)
55
Head lamp (Low)
35
Front turn signal lamp
21
Front position lamp
6
Front fog lamp
27
Rear stop/tail lamp (Outside)
8/27
Back up lamp
16
Rear turn signal lamp
21
Rear fog lamp - Europe
21
License plate lamp
5
Side repeater
5
Room lamp
10
Overhead console lamp
10
High mounted stop lamp
5
Glove box lamp
5
Rear map lamp
10
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст