Hyundai Santa Fe (2006 year). Manual — part 86
ATA -102
AUTOMATIC TRANSAXLE (A5HF1)
2.
CHECK PCM/TCM
1)
Connect scantool to data link connector(DLC).
2)
Ignition "ON" & Engine "OFF".
3)
Select A/T Solenoid valve Actuator test and Operate Actuator test.
4)
Can you hear operating sound for "PRESS CONTROL SOL VALVE(VFS)" Actuator testing function?
YES
▶ Go to "Verification of vehicle repair" procedure.
NO
▶ Replace PCM/TCM as necessary and go to "Verification of vehicle repair" procedure.
ACTUATOR TEST CONDITION
1.
IG SWITCH ON
2.
TRANSAXLE RANGE SWITCH is normal
3.
P RANGE
4.
Vehicle Speed 0mph(0km/h)
5.
Throttle position sensor< 1V
6.
IDLE SWITCH ON
7.
ENGINE RPM 0
VERIFICATION OF VEHICLE REPAIR
E34559E6
Refer to DTC P0743.
AUTOMATIC TRANSAXLE SYSTEM
ATA -103
DTC P0750 SHIFT CONTROL SOLENOID VALVE A CIRCUIT MALFUNCTION
COMPONENT LOCATION
EC54E5ED
AKKF117G
GENERAL DESCRIPTION
E9004129
The Automatic transmission changes the gear position of the transmission by utilizing a combination of clutches and
brakes, which are controlled by solenoid valves. This automatic transmission consists of a: LR (Low and Reverse Brake),
2ND (2nd Brake), UD (Under Drive Clutch), OD (Over Drive Clutch), REV (Reverse Clutch), and a RED (Reduction Brake,
only for 5 speed transmissions). The LR Brake is engaged in the 1st gear and reverse gear positions.
DTC DESCRIPTION
E700E62E
The TCM checks the Low and Reverse Control Signal by monitoring the feedback signal from the solenoid valve drive
circuit. If an unexpected signal is monitored (for example, high voltage is detected when low voltage is expected, or low
voltage is detected when high voltage is expected), the TCM judges that the Low and Reverse control solenoid circuit is
malfunctioning and sets this code.
DTC DETECTING CONDITION
ECAEDCB1
Item
Detecting Condition
Possible cause
DTC Strategy
• Check voltage range
Enable Conditions
• Not being control for "N-D or N-R"
• Voltage of AT relay ≥ 10V
• Not Fail Safe Status
• IG "ON"
Threshold value
• Out of available voltage range
Diagnostic Time
• more than 320 ms
Fail Safe
• Locked in 3 rd gear.(Control relay off)
• Open or short in circuit
• Faulty LR SOLENOID VALVE
• Faulty PCM/TCM
SPECIFICATION
EBBA2E7C
Refer to DTC P0743.
ATA -104
AUTOMATIC TRANSAXLE (A5HF1)
SIGNAL WAVEFORM
E657B66E
FIG.1)
FIG.1) : "2nd" gear
EKBF117A
MONITOR SCANTOOL DATA
EBC98BD9
1.
Connect scantool to data link connector(DLC).
2.
Engine "ON".
3.
Monitor the "LR SOL. VALVE" parameter on the scantool.
4.
Shift gear at each position.
AUTOMATIC TRANSAXLE SYSTEM
ATA -105
FIG.1)
FIG.2)
FIG. 1) P,N
FIG. 2) "R"
FIG. 3) "D 1st" gear
FIG. 4) "2nd" gear
FIG. 5) "3rd" gear
FIG. 6) "4th" gear
FIG. 7) "5th" gear
FIG.3)
FIG.4)
FIG.5)
FIG.6)
FIG.7)
LKKG209D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст