Hyundai Santa Fe (2006 year). Manual — part 738
MANUAL TRANSAXLE SYSTEM
MTA -9
7.
Remove the ground wire (A) from the transaxle case.
A
SCMMT6006D
8.
Remove the vehicle speed sensor connector (A).
A
SCMMT6007D
9.
Remove the control cable assemblies(A) by removing
the snap pins(B) and clips(C).
A
B
C
SCMMT6008D
10. Disconnect the "N" (A) and the "R" (B) position switch.
A
B
SCMMT6009D
11. Remove C.S.C (Concentric Slave Cylinder) tube(A)
which is being clamped by loosening the nut(B).
A
B
SCMMT6010D
12. Remove the four mounting bolts(A) of upper part of
the transaxle.
A
SCMMT6011D
MTA -10
MANUAL TRANSAXLE (M5HF2)
13. Support the engine and transaxle by using the special
tool (09200-38001).
09200-38001
SCMMT6012D
14. Remove the transaxle insulator bracket (B) by remov-
ing the bolts (A).
A
B
SCMMT6013D
15. Remove the front wheels and tires. (see SS group)
16. Lift up the vehicle.
17. Remove the steering column joint bolt.
(see ST
group).
18. Remove the under cover(A).
A
SCMMT6014D
19. Drain power steering oil through the return tube. (see
ST group)
20. Disconnect the power steering pressure hose (A) from
the power steering oil pump.
21. Drain the tranaxle fluid through the drain plug.
22. Disconnect the lower arm, the tie rod end ball joint,
the stabilizer bar link from the front knuckle. (see SS
group)
23. Remove the roll stopper mounting bolts.
24. Remove the mounting bolts from the sub frame by
supporting the sub frame with a jack. (see SS group)
25. Remove the drive shafts from the transaxle. (see DS
group)
26. Disconnect the starter motor connector and remove
the starter motor. (see EE group)
27. In case of 4WD, remove the transfer case assem-
bly.(see ’Transfer case’ removal).
MANUAL TRANSAXLE SYSTEM
MTA -11
28. Remove the mounting bolts(A-3ea, B-2ea) of lower
part of the transaxle, and the left side cover and re-
move the transaxle assembly by supporting it with a
jack.
A
SCMMT6017D
B
SCMMT6018D
INSTALLATION
E552EB03
Installation is in the reverse order of removal.
Perform the following :
• Adjust the shift cable.
• Refill the transaxle with fluid.
• Refill the radiator with engine coolant.
• Bleed air from the cooling system with the heater
valve open.
• Clean the battery posts and cable terminals with
sandpaper, assemble them, and apply grease to
prevent corrosion.
1.
Lowering the vehicle or lifting up a jack, install the
transaxle assembly.
2.
Tighten the transaxle under mounting bolts(A-3ea,
B-2ea).
TORQUE:
65~85 Nm(6.5~8.5 kgf.m, 47.0~61.5 lb-ft)
A
SCMMT6017D
B
SCMMT6018D
MTA -12
MANUAL TRANSAXLE (M5HF2)
3.
Install the starter motor and connect the starter motor
connector. (see EE group)
4.
In case of 4WD, install the transfer case assem-
bly.(see ’Transfer case’ installation)
5.
Install the drive shafts to the transaxle. (See "DS"
group)
6.
Install the transaxle insulator (B) and mounting
bracket (C) by tightening the bolts (A).
TORQUE:
60~80 Nm (6~8 kgf.m, 43.6~58.2 lb-ft)
A
B
SCMMT6013D
7.
Install the sub frame. (see SS group)
TORQUE:
60~80 Nm(6~8 kgf.m, 65.1~79.5 lb-ft)
8.
Connect the power steering return hose. (see ST
group)
9.
Connect the lower arm, the rod end ball joint, the sta-
bilizer bar link to the front knuckle.(see SS group)
10. Install the steering column joint bolt.(See ST group).
11. Install the C.S.C (Cincentric Slave Cylinder) tube(A)
by tightening the nut(B).
A
B
SCMMT6010D
12. Refill transaxle oil through the inlet hole(A).
TORQUE:
30~35 Nm(3.0~3.5 kgf.m, 21.8~25.4 lb-ft)
A
AMKF002J
13. Install the under cover(A).
A
SCMMT6014D
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст