Hyundai Santa Fe (2006 year). Manual — part 49
AT -148
AUTOMATIC TRANSAXLE (F4A51)
5.
Does "OD SOLENOID DUTY " follow the reference data?
YES
▶ Fault is intermittent caused by poor contact in the sensor’s and/or TCM(PCM)’s connector or was repaired and
TCM(PCM) memory was not cleared. Thoroughly check connectors for looseness, poor connection, bending, cor-
rosion, contamination, deterioration or damage. Repair or replace as necessary and go to "Verification of vehicle
repair" procedure.
NO
▶ Go to "Terminal&connector inspection " procedure.
TERMINAL & CONNECTOR INSPECTION
EE0FBE41
Refer to DTC P0743.
POWER SUPPLY CIRCUIT INSPECTION
E4ECB63A
1.
Disconnect "A/T SOLENOID VALVE" connector.
2.
Measure voltage between terminal "6" of the sensor harness connector and chassis ground.
3.
Turn ignition switch OFF → ON.
Specification: 12V is measured only for approx. 0.5sec
1
2
3
4
5
6
7
8
9
10
11
12
3. UD solenoid valve
4. 2ND solenoid valve
5. A/T battery
7. VF solenoid valve(+)
8. VF solenoid valve(-)
9. DCC solenoid valve
10.RED solenoid valve
11. LR solenoid valve
12. OD solenoid valve
C09
v
SCMAT6746L
4.
Is voltage within specifications?
YES
▶ Go to "Signal circuit inspection" procedure.
NO
▶ Check that A/T-20A fuse in engine room junction is installed or not blown.
▶ Check for open in harness. Repair as necessary and go to "Verification of vehicle repair" procedure.
AUTOMATIC TRANSAXLE SYSTEM
AT -149
SIGNAL CIRCUIT INSPECTION
ED6CEE06
1.
Check signal circuit open inspection
1)
Ignition "OFF".
2)
Disconnect "A/T SOLENOID VALVE" connector and "PCM/TCM" connector.
3)
Measure resistance between terminal "12" of the ATM SOLENOID VALVE harness connector and terminal "42"
of the PCM/TCM harness connector.
Specification: approx. 0 Ω
1
2
3
4
5
6
7
8
9
10
11
12
C09
3. UD solenoid valve
4. 2ND solenoid valve
5. A/T battery
6. A/T battery
7. VF solenoid valve(+)
8. VF solenoid valve(-)
9. DCC solenoid valve
10.RED solenoid valve
11. LR solenoid valve
12. OD solenoid valve
42.OD solenoid valve control
45.2ND solenoid valve control
43.DCC solenoid valve control
44.RED solenoid valve
75.VF solenoid valve(+)
59.VF solenoid valve(-)
22.LR solenoid valve control
03.UD solenoid valve control
Ω
C30-B
3 2 1
6
4
9
21
22
23
16 15
17
18
19
11 10
12
13
14
38 37
39
40
25 24
28
29
48
49
68 67
69
70
42 41
43
44
62 61
63
64
45
56
57
58
59
60
78
79
52 51 50
53
72 71
73
74
76 75
77
54
55
32
33
30
31
35
36
34
*
*
*
*
*
*
*
*
*
8 7
SCMAT6756L
4)
Is resistance within specifications?
YES
▶ Go to "Check signal circuit short inspection" procedure.
NO
▶ Check for open in harness. Repair as necessary and go to "Verification of vehicle repair" procedure.
2.
Check signal circuit short inspection
1)
Ignition "OFF".
2)
Disconnect "A/T SOLENOID VALVE" connector and "PCM/TCM" connector.
3)
Measure resistance between terminal "12" of the ATM SOLENOID VALVE harness and chassis ground.
Specification: Infinite
AT -150
AUTOMATIC TRANSAXLE (F4A51)
1
2
3
4
5
6
7
8
9
10
11
12
3. UD solenoid valve
4. 2ND solenoid valve
5. A/T battery
6. A/T battery
7. VF solenoid valve(+)
8. VF solenoid valve(-)
9. DCC solenoid valve
10.RED solenoid valve
11. LR solenoid valve
12. OD solenoid valve
C09
Ω
SCMAT6757L
4)
Is resistance within specifications?
YES
▶ Go to "Component inspection" procedure.
NO
▶ Check for short to ground in harness. Repair as necessary and go to "Verification of vehicle repair" procedure.
COMPONENT INSPECTION
E39F8164
1.
CHECK SOLENOID VALVE
1)
Ignition "OFF".
2)
Disconnect "A/T SOLENOID VALVE" connector.
3)
Measure resistance between terminal "6" and terminal "12" of the ATM SOLENOID VALVE harness connector.
Specification: Approximately 2.7~3.4 Ω [20 C(68 F)]
3. UD solenoid valve
4. 2ND solenoid valve
5. A/T battery
7. VF solenoid valve(+)
8. VF solenoid valve(-)
9. DCC solenoid valve
10.RED solenoid valve
11. LR solenoid valve
12. OD solenoid valve
C09
Ω
1 2 3 4
5
6
7
8
9 10 1112
Component Side
SCMAT6758L
4)
Is resistance within specification?
YES
▶ Go to "CHECK PCM/TCM" as below.
NO
▶ Replace OD SOLENOID VALVE as necessary and go to "Verification of vehicle repair" procedure.
AUTOMATIC TRANSAXLE SYSTEM
AT -151
2.
CHECK PCM/TCM
1)
Connect scantool to data link connector(DLC).
2)
Ignition "ON" & Engine "OFF".
3)
Select A/T solenoid valve actuator test and operate actuator test.
4)
Can you hear operating sound for OD SOLENOID VALVE actuator testing function?
YES
▶ Go to "Verification of vehicle repair" procedure.
NO
▶ Replace PCM/TCM and go to "Verification of vehicle repair" procedure.
ACTUATOR TEST CONDITION
1.
IG SWITCH ON
2.
TRANSAXLE RANGE SWITCH is normal
3.
P RANGE
4.
Vehicle Speed 0mph(0km/h)
5.
Throttle position sensor < 1V
6.
IDLE SWITCH ON
7.
ENGINE RPM 0
VERIFICATION OF VEHICLE REPAIR
E4B7ED91
Refer to DTC P0743.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст