Hyundai Santa Fe (2006 year). Manual — part 110
EXTERIOR
BD -23
SPEAKER REPLACEMENT
1.
Remove the front door trim. (See page BD- 21)
2.
After disconnecting the connector (A), remove the
power window motor (B).
A
B
SCMBD6033D
3.
Installation is the reverse of removal.
POWER WINDOW MOTOR REPLACEMENT
1.
Remove the door trim. (See page BD- 21)
2.
After disconnecting the connector (A), remove the
power window motor (B).
A
B
Fastener Locations
: Screw, 2
: Screw, 1
SCMBD6034L
3.
Installation is the reverse of removal.
NOTE
-
Roll the glass up down to see if it move freely
without binding.
BD -24
BODY (INTERIOR AND EXTERIOR)
FRONT DOOR MODULE ASSEMBLY
REPLACEMENT
1.
Remove the following parts.
-
Front door trim. (See page BD- 21)
-
Window glass. (See page BD- 22)
-
Outside handle. (See page BD- 25)
2.
Loosen the outside handle base mounting screw (A).
A
: Screw Locations, 1
SCMBD6035L
3.
Loosen the module (A) mounting bolts and latch
mounting screws.
A
Fastener Locations
: Bolt, 8
: Screw, 3
7.8~11.8 N.m
(0.8~1.2 Kgf.m,
5.1~8.7 lbf.ft)
6.9~10.8 N.m
(0.7~1.1 Kgf.m,
5.1~8.0 lbf.ft)
SCMBD6036L
4.
Disconnect the door module wiring harness (A), then
remove the module assembly (B).
A
B
C
SCMBD6037D
5.
Installation is the reverse of removal.
NOTE
-
Make sure the connector are plugged in properly
and each rod is connected securely.
-
Make sure the door locks and opens properly.
EXTERIOR
BD -25
LATCH ASSEMBLY REPLACEMENT
1.
Remove the following parts.
-
Front door trim. (See page BD- 21)
-
Window glass. (See page BD- 22)
-
Inside handle. (See page BD- 8)
-
Door module. (See page BD- 24)
2.
Remove the latch assembly (A).
A
B
SCMBD6505D
3.
Installation is the reverse the removal.
NOTE
-
Make sure the door locks and opens properly.
OUTSIDE HANDLE REPLACEMENT
1.
Loosen the mounting bolt, then remove the key holder
(A).
A
: Bolt Locations
6.9~10.8 N.m
(0.7~1.1 Kgf.m,
5.1~8.0 lbf.ft)
SCMBD6038L
2.
Remove the outside handle (A).
A
SCMBD6039D
3.
Installation is the reverse of removal.
BD -26
BODY (INTERIOR AND EXTERIOR)
DOOR CHECKER REPLACEMENT
1.
Remove the front door trim. (See page BD- 21)
2.
Remove the door module. (See page BD- 24)
3.
Loosen the mounting bolt, then remove the rear
checker (A).
A
Fastener Locations
: Bolt, 2
: Bolt, 1
6.9~10.8N.m
(0.7 ~ 1.1Kgf.m,
5.1~8.0lbf.ft)
16.7~21.6N.m
(1.7 ~ 2.2Kgf.m,
12.3~15.9lbf.ft)
LSLG006O
4.
Installation is the reverse the removal.
DOOR BELT WEATHERSTRIP REPLACEMENT
1.
Loosen the mounting screw, then remove the door
belt weatherstrip (A).
A
: Screw Locations, 1
LSLG140N
2.
Installation is the reverse of removal.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст