Hyundai Santa Fe (2019 year). Instruction — part 15
DEFROSTER
NOTICE
NOTICE
• To turn off the defroster, press the
rear window defroster button again.
The system may not work proper-
To prevent damage to the conduc-
ly by providing incorrect mes-
tors bonded to the inside surface
i
Information
sages when the sensors are inter-
of the rear window, never use
fered by other vehicle sensors and
sharp instruments or window
• If there is heavy accumulation of
noise, or it is on a road that inter-
cleaners containing abrasives to
snow on the rear window, brush it off
feres with receiving signals.
clean the window.
before operating the rear defroster.
3
• The rear window defroster automat-
i
Information
ically turns off after approximately
20 minutes or when the ignition
If you want to defrost and defog the
switch is in the OFF position.
front
windscreen,
refer
to
“Windscreen
Defrosting
and
Defogging” in this chapter.
Outside mirror defroster
(if equipped)
Rear window defroster
If your vehicle is equipped with out-
side mirror defrosters, they will oper-
The defroster heats
ate at the same time you turn on the
the window to remove
rear window defroster.
frost, fog and thin ice
from the interior and
exterior of the rear win-
dow, whilst the engine
is running.
• To activate the rear window
defroster, press the rear window
defroster button located in the cen-
tre facia switch panel. The indicator
on the rear window defroster but-
ton illuminates when the defroster
is ON.
3-161
Convenient features of your vehicle
MANUAL CLIMATE CONTROL SYSTEM (IF EQUIPPED)
■ Type A
1. Fan speed control knob
2. Temperature control knob
3. Mode selection button
■ Type B
4. Front windscreen defroster button
5. Rear window defroster button
6. Air conditioning button*
7. Air intake control button
8.3rd row seat Air conditioning
ON/OFF button*
9.3rd row seat Air conditioning fan
speed control knob*
■ 3rd row air conditioning control (for Type B climate control)
* : if equipped
OTM048300L/OTM048301/OTM048302
3-162
Heating and air conditioning
Mode selection (3)
1. Start the engine.
2. Set the mode to the desired posi-
tion.
To improve the effectiveness of
heating and cooling, select:
- Heating:
3
- Cooling:
3. Set the temperature control to the
desired position.
4. Set the air intake control to the
outside (fresh) air position.
5. Set the fan speed control to the
desired speed.
6. If air conditioning is desired, turn
the air conditioning system on.
OTM048330R
The mode selection button controls the direction of the air flow through the
ventilation system.
❈ 3rd row outlet vents (G, H) (if equipped)
• The air flow of 3rd row outlet vents (G) is controlled by the front climate con-
trol system and delivered through the inside air duct of the floor.
• The air flow of the 3rd row outlet vents (G) may be weaker than the instru-
ment panel vents for the long air duct.
• The air flow of 3rd row side vents (H) is controlled by the 3rd row seat air
conditioning button and knob.
3-163
Convenient features of your vehicle
Floor/Defrost-Level
Face-Level (B, D, E)
(A, C, D, E, F, G)
Most of the air flow is directed to the
Air flow is directed toward the upper
floor and the windscreen with a small
body and face. Additionally, each
amount directed to the side window
outlet can be controlled to direct the
defrosters.
air discharged from the outlet.
Front defroster (4) (A, D)
Bi-Level (B, C, D, E, F, G)
Most of the air flow is directed to the
OTM048304
Air flow is directed towards the face
windscreen with a small amount of air
A/C MAX-Level (B, D)
and the floor.
directed to the side window defrosters.
(if equipped)
To operate the A/C MAX, turn the
Floor-Level
temperature control knob to extreme
(A, C, D, E, F, G)
left. Air flow is directed toward the
upper body and face.
Most of the air flow is directed to the
In this mode, the air conditioning and
floor, with a small amount of the air
the recirculated air position will be
being directed to the windscreen and
selected automatically.
side window defrosters.
After the interior has cooled suffi-
ciently, whenever possible, move the
temperature knob away from A/C
MAX and press the A/C button.
3-164
■ Front
Temperature control (2)
Outside (fresh) air position
The temperature will increase by turn-
■ Type A
With the outside (fresh)
ing the knob to the right. The tempera-
air position selected, air
ture will decrease by turning the knob
enters the vehicle from
to the left.
outside and is heated or
cooled according to the
■ Type B
function selected.
Air intake control (7)
3
This is used to select outside (fresh)
air position or recirculated air position.
To change the air intake control posi-
OTM048307R
tion, press the control button.
i
Information
■ Rear
Recirculated air position
Using the system in the fresh air posi-
tion is recommended.
With the recirculated air
position selected, air from
Prolonged operation of the heater in
the passenger compart-
the recirculated air position (without
ment will be drawn
air conditioning selected) can cause
through the heating sys-
fogging of the windscreen and side
tem and heated or cooled
windows and the air within the passen-
according to the function
ger compartment will become stale.
selected.
In addition, prolonged use of the air
conditioning with the recirculated air
OTM048308
position selected will result in exces-
sively dry air in the passenger com-
Instrument panel vents
partment.
The outlet vents can be opened or
closed separately using the vent
control lever. If you move the vent
control lever to the left end, the outlet
vents can be closed.
3-165
Convenient features of your vehicle
Fan speed control (1)
3rd row air conditioning
WARNING
Turn the knob to the right to increase
(if equipped)
the fan speed and airflow. Turn the
•
Continued climate control
knob to the left to decrease fan
system operation in the recir-
speed and airflow.
culated air position may allow
humidity to increase inside
Setting the fan speed control knob to
the vehicle which may fog the
the “0” position turns off the fan.
glass and obscure visibility.
•
Do not sleep in a vehicle with
NOTICE
the air conditioning or heating
Operating the fan speed when the
system on. It may cause seri-
ignition switch is in the ON posi-
ous harm or death due to a
tion could cause the battery to
drop in the oxygen level
discharge. Operate the fan speed
and/or body temperature.
OTM048312L
when the engine is running.
[A] : Front, [B] : Rear left, [C] : Rear right
•
Continued climate control sys-
tem operation in the recirculat-
To turn on the 3rd row air condition-
Air conditioning (A/C) (6)
ed air position can cause
ing control system
(if equipped)
drowsiness or sleepiness, and
1. Press the 3rd row air conditioning
loss of vehicle control. Set the
Press the A/C button to turn the air
ON/OFF button (8) located on the
air intake control to the outside
conditioning system on
(indicator
front climate control panel and set
(fresh) air position as much as
light will illuminate). Press the button
the fan speed to the desired speed
possible whilst driving.
again to turn the air conditioning sys-
with the 3rd row fan speed knob
tem off.
(9). (indicator light on the ON/OFF
button will illuminate).
3-166
2. To turn off the 3rd row air condi-
4. Set the fan speed control to the
Air conditioning
tioning control system, press the
desired speed.
HYUNDAI Air Conditioning Systems
3rd row air conditioning ON/OFF
5. If dehumidified heating is desired,
are filled with R-134a or R-1234yf
button once more located on the
turn the air conditioning system (if
refrigerant.
front climate control panel or set
equipped) on.
1. Start the engine. Push the air con-
the fan speed to the OFF position
If the windscreen fogs up, set the
ditioning button.
with the 3rd row fan speed switch
mode to the
or
position.
(indicator light on the ON/OFF but-
2. Set the mode to the
position.
3
ton is not illuminated).
3. Set the air intake control to the out-
Operation Tips
side air or recirculated air position.
•
To keep dust or unpleasant fumes
4. Adjust the fan speed control and
System operation
from entering the vehicle through
temperature control to maintain
Ventilation
the ventilation system, temporarily
maximum comfort.
1. Set the mode to the
position.
set the air intake control to the
recirculated air position. Be sure to
2. Set the air intake control to the
i
Information
return the control to the fresh air
outside (fresh) air position.
position when the irritation has
Your vehicle is filled with R-134a or
3. Set the temperature control to the
R-1234yf according to the regulation
passed to keep fresh air in the
desired position.
vehicle. This will help keep the driv-
in your country at the time of produc-
4. Set the fan speed control to the
er alert and comfortable.
tion. You can find out which air condi-
desired speed.
tioning refrigerant is applied to your
•
To prevent interior fog on the wind-
vehicle on the label located inside of
screen, set the air intake control to
the bonnet. Refer to chapter 8 for the
the fresh air position and fan speed
Heating
location of the air conditioning refrig-
to the desired position, turn on the
1. Set the mode to the
position.
erant label.
air conditioning system, and adjust
2. Set the air intake control to the
the temperature control to the
outside (fresh) air position.
desired temperature.
3. Set the temperature control to the
desired position.
3-167
Convenient features of your vehicle
NOTICE
• When opening the windows in
• Use the air conditioning system
humid weather air conditioning
every month for a few minutes to
•
The refrigerant system should
may create water droplets inside
ensure maximum system perform-
only be serviced by trained and
the vehicle. Since excessive
ance.
certified technicians to insure
water droplets may cause dam-
• If you operate the air conditioner
proper and safe operation.
age to electrical equipment, air
excessively, the difference between
•
The refrigerant system should
conditioning should only be
the temperature of the outside air
be serviced in a well-ventilated
used with the windows closed.
and that of the windscreen could
place.
cause the outer surface of the
•
The air conditioning evaporator
windscreen to fog up, causing loss
Air conditioning system operation
(cooling coil) shall never be
of visibility. In this case, set the
tips
repaired or replaced with one
mode selection knob to the
• If the vehicle has been parked in
removed from a used or sal-
position and set the fan speed con-
direct sunlight during hot weather,
vaged vehicle and new replace-
trol knob to the lowest speed set-
open the windows for a short time
ment MAC evaporators shall be
ting.
to let the hot air inside the vehicle
certified (and labelled) as meet-
escape.
ing SAE Standard J2842.
• After sufficient cooling has been
NOTICE
achieved, switch back from the
recirculated air to the fresh outside
• When using the air conditioning
air position.
system, monitor the temperature
• To help reduce moisture inside of
gauge closely whilst driving up
the windows on rainy or humid
hills or in heavy traffic when out-
days, decrease the humidity inside
side temperatures are high. Air
the vehicle by operating the air
conditioning system operation
conditioning system with the win-
may cause engine overheating.
dows and sunroof closed.
Continue to use the fan but turn
the air conditioning system off if
the temperature gauge indicates
engine overheating.
3-168
System maintenance
If the vehicle is being driven in
Checking the amount of air con-
severe conditions such as dusty or
ditioner refrigerant and com-
Climate control air filter
rough roads, more frequent climate
pressor lubricant
control filter
inspections and
When the amount of refrigerant is
changes are required.
low, the performance of the air con-
If the air flow rate suddenly decreas-
ditioning is reduced. Overfilling also
es, we recommend the system be
reduces the performance of the air
checked at a HYUNDAI authorised
conditioning system.
3
repairer.
Therefore, if abnormal operation is
found, we recommend that the sys-
NOTICE
tem be inspected by a HYUNDAI
authorised repairer.
It is important that the correct
type and amount of oil and refrig-
OIK047401L
erant is used. Otherwise, damage
WARNING
[A] : Outside air, [B] : Recirculated air
to the compressor and abnormal
[C] : Climate control air filter, [D] : Blower
system operation may occur.
Vehicles equipped with R-134a
[E] : Evaporator core, [F] : Heater core
Because the refriger-
This filter is installed behind the
ant is at very high
glove box. It filters the dust or other
pressure, the air condi-
pollutants that enter the vehicle
tioning system should
through the heating and air condi-
only be serviced by trained and
tioning system.
certified technicians. It is impor-
We recommend that the climate con-
tant that the correct type and
trol air filter be replaced by a
amount of oil and refrigerant is
HYUNDAI authorised repairer
used. Otherwise, it may cause
according to the maintenance sched-
damage to the vehicle and per-
ule.
sonal injury.
3-169
Convenient features of your vehicle
Air conditioning refrigerant
Each symbols and specification on
WARNING
label
air conditioning refrigerant label
means as below:
Vehicles equipped with R-1234yf
■ Example
• Type A
Because the refriger-
1. Classification of refrigerant
ant is mildly inflamma-
2. Amount of refrigerant
ble at very high pres-
sure, the air condition-
3. Classification of Compressor lubri-
ing system should only
cant
be serviced by trained
and certified techni-
You can find out which air conditioning
cians. It is important
refrigerant is applied to your vehicle on
that the correct type and amount
the label located inside of the bonnet.
of oil and refrigerant is used.
ODH044365R
Refer to chapter 8 for the location of
Otherwise, it may cause dam-
the air conditioning refrigerant label.
age to the vehicle and personal
• Type B
injury.
We recommend the air conditioning
system be serviced by a HYUNDAI
authorised repairer.
ODH043366
The actual Air Conditioning refriger-
ant label in the vehicle may differ
from the illustration.
3-170
AUTOMATIC CLIMATE CONTROL SYSTEM (IF EQUIPPED)
■ Type A
1. Passenger’s temperature control knob
2. Driver’s temperature control knob
3. SYNC button
3
4. AUTO (automatic control) button
5. OFF button
■ Type B
6. Air conditioning button
7. Front windscreen defroster button
8. Fan speed control button
9. Mode selection button
10. Rear window defroster button
11. Air intake control button
12.3rd row seat Air conditioning
ON/OFF button*
13.3rd row seat Air conditioning fan
■ 3rd row air conditioning control (for Type B climate control)
speed control knob*
14. Climate control information screen
* : if equipped
OTM048313R/OTM048314R/OUM046445L
3-171
Convenient features of your vehicle
Automatic heating and air con-
- Fan speed control button
Manual heating and air condi-
ditioning
The selected function will be con-
tioning
trolled manually whilst other func-
The Automatic Climate Control
The heating and cooling system can be
tions operate automatically.
System is controlled by setting the
controlled manually by pushing buttons
desired temperature.
For your convenience and to improve
other than the AUTO button. In this
1. Press the AUTO button (4).
the effectiveness of the climate con-
case, the system works sequentially
trol, use the AUTO button and set the
according to the order of buttons select-
The modes, fan speeds, air intake
temperature to 23°C (73°F).
ed. When pressing any button except
and air-conditioning will be controlled
the AUTO button whilst using automat-
automatically by the temperature set-
ic operation, the functions not selected
ting you select.
will be controlled automatically.
2. Turn the temperature control knob
1. Start the engine.
(1, 2) to the desired temperature. If
2. Set the mode to the desired posi-
the temperature is set to the low-
tion.
est setting (Lo), the air condition-
ing system will operate continu-
For improving the effectiveness of
ously. After the interior has cooled
heating and cooling, select:
sufficiently, adjust the knob to a
- Heating:
higher temperature set point
- Cooling:
whenever possible.
3. Set the temperature control to the
OTM048315
desired position.
To turn the automatic operation off,
select any button of the following:
i
Information
4. Set the air intake control to the
outside (fresh) air position.
- Mode selection button
Never place anything near the sensor
5. Set the fan speed control to the
- Front windscreen defroster button
to ensure better control of the heating
desired speed.
(Press the button one more time to
and cooling system.
deselect the front windscreen
6. If air conditioning is desired, turn
defroster function. The 'AUTO' sign
the air conditioning system on.
will illuminate on the information
7. Press the AUTO button to convert
display once again.)
to full automatic control of the sys-
tem.
3-172
Mode selection (9)
Face-Level (B, D, E)
Air flow is directed toward the upper
body and face. Additionally, each
outlet can be controlled to direct the
air discharged from the outlet.
3
Bi-Level (B, C, D, E, F, G)
Air flow is directed towards the face
and the floor.
Floor-Level
(A, C, D, E, F, G)
OTM048330R
Most of the air flow is directed to the
The mode selection button controls the direction of the air flow through the
floor, with a small amount of the air
ventilation system.
being directed to the windscreen and
❈ 3rd row outlet vents (G, H) (if equipped)
side window defrosters.
• The air flow of 3rd row outlet vents (G) is controlled by the front climate con-
trol system and delivered through the inside air duct of the floor.
• The air flow of the 3rd row outlet vents (G) may be weaker than the instru-
ment panel vents for the long air duct.
• The air flow of 3rd row side vents (H) is controlled by the 3rd row seat air
conditioning button and knob.
3-173
Convenient features of your vehicle
■ Front
Temperature control (1, 2)
Floor/Defrost-Level
(A, C, D, E, F, G)
■ Driver side
■ Passenger side
Most of the air flow is directed to the
floor and the windscreen with a small
amount directed to the side window
defrosters.
Defrost-Level (7) (A, D)
Most of the air flow is directed to the
windscreen with a small amount of air
OTM048307R
directed to the side window defrosters.
■ Rear
OTM048317R
The temperature will increase by
turning the knob to the right. The
temperature will decrease by turning
the knob to the left.
OTM048308
Instrument panel vents
The outlet vents can be opened or
closed separately using the vent
control lever. If you move the vent
control lever to the left end, the outlet
vents can be closed.
3-174
Adjusting the driver and passenger
Air intake control (11)
side temperature individually
This is used to select the outside
Press the “SYNC” button again to
(fresh) air position or recirculated air
adjust the driver and passenger side
position.
temperature individually. The button
To change the air intake control posi-
indicator will turn off.
tion, push the control button.
3
Temperature conversion
Recirculated air position
If the battery has been discharged or
With the recirculated air
disconnected, the temperature mode
position selected, air
display will reset to Centigrade.
OTM048319R
from the passenger com-
To change the temperature unit from
partment will be drawn
Adjusting the driver and passenger
°C to °F or °F to °C :
through the heating sys-
side temperature equally
tem and heated or
- Automatic climate control system
• Press the
“SYNC” button
(3) to
cooled according to the
adjust the driver and passenger
Press the AUTO button for 3 sec-
function selected.
side temperature equally.
onds whilst pressing the OFF but-
The passenger side temperature
ton.
Outside (fresh) air position
will be set to the same temperature
- Instrument cluster
as the driver side temperature.
■ Type A
With the outside (fresh)
Go to User Settings → Other fea-
air position selected, air
• Turn the driver side temperature
tures → Temperature unit.
enters the vehicle from
control knob. The driver and pas-
The temperature unit on both the
outside and is heated or
senger side temperature will be
cluster LCD display and the climate
cooled according to the
adjusted equally.
control screen will change.
■ Type B
function selected.
3-175
Convenient features of your vehicle
Fan speed control (8)
i
Information
WARNING
The fan speed can be set as desired
Using the system in the fresh air posi-
by pushing the fan speed control but-
tion is recommended.
•
Continued climate control
ton.
system operation in the recir-
Prolonged operation of the heater in
culated air position may allow
More air is delivered with higher fan
the recirculated air position (without
humidity to increase inside
speeds.
air conditioning selected) can cause
the vehicle which may fog the
Pressing the OFF button turns off the
fogging of the windscreen and side
glass and obscure visibility.
fan.
windows and the air within the passen-
ger compartment will become stale.
•
Do not sleep in a vehicle with
NOTICE
the air conditioning or heating
In addition, prolonged use of the air
system on. It may cause seri-
Operating the fan when the ignition
conditioning with the recirculated air
switch is in the ON position could
ous harm or death due to a
position selected will result in exces-
drop in the oxygen level
cause the battery to discharge.
sively dry air in the passenger com-
Operate the fan when the engine is
and/or body temperature.
partment.
running.
•
Continued climate control sys-
tem operation in the recirculat-
ed air position can cause
Air conditioning (6)
drowsiness or sleepiness, and
Push the A/C button to turn the air
loss of vehicle control. Set the
conditioning system on
(indicator
air intake control to the outside
light will illuminate).
(fresh) air position as much as
Push the button again to turn the air
possible whilst driving.
conditioning system off.
OFF mode (5)
Push the OFF button to turn the cli-
mate control system off. However,
you can still operate the mode and air
intake buttons as long as the ignition
switch is in the ON position.
3-176
3rd row air conditioning
2. To turn off the 3rd row air condi-
5. If dehumidified heating is desired,
(if equipped)
tioning control system, press the
turn the air conditioning system on.
3rd row air conditioning ON/OFF
• If the windscreen fogs up, set the
button once more located on the
mode to the
or
position.
front climate control panel or set
the fan speed to the OFF position
with the 3rd row fan speed switch
Operation Tips
(indicator light on the ON/OFF but-
•
To keep dust or unpleasant fumes
3
ton is not illuminated).
from entering the vehicle through
the ventilation system, temporarily
set the air intake control to the
System operation
recirculated air position. Be sure to
Ventilation
return the control to the fresh air
position when the irritation has
1. Set the mode to the
position.
OTM048312L
passed to keep fresh air in the
[A] : Front, [B] : Rear left, [C] : Rear right
2. Set the air intake control to the
vehicle. This will help keep the driv-
outside (fresh) air position.
er alert and comfortable.
To turn on the 3rd row air condition-
3. Set the temperature control to the
•
To prevent interior fog on the wind-
ing control system
desired position.
screen, set the air intake control to
1. Press the 3rd row air conditioning
4. Set the fan speed control to the
the fresh air position and fan speed
ON/OFF button (12) located on
desired speed.
to the desired position, turn on the air
the front climate control panel and
conditioning system, and adjust the
set the fan speed to the desired
Heating
temperature control to the desired
speed with the 3rd row fan speed
1. Set the mode to the
position.
temperature.
knob (13) (indicator light on the
2. Set the air intake control to the
ON/OFF button will illuminate).
outside (fresh) air position.
3. Set the temperature control to the
desired position.
4. Set the fan speed control to the
desired speed.
3-177
Большое спасибо!
Ваше мнение очень важно для нас.
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст