Hyundai Veloster (2019 year). Instruction — part 27

Maintenance

NOTICE

Repairing your vehicle's finish

Bright-metal maintenance

Deep scratches or stone chips in the

• To remove road tar and insects,

• Wiping dust or dirt off the body

painted surface must be repaired

use a tar remover, not a scraper or

with a dry cloth will scratch the

promptly. Exposed metal will quickly

other sharp object.

finish.

rust and may develop into a major

• To protect the surfaces of bright-

• Do not use steel wool, abrasive

repair expense.

metal parts from corrosion, apply a

cleaners, or strong detergents

coating of wax or chrome preser-

containing highly alkaline or

NOTICE

vative and rub to a high luster.

caustic agents on chrome-plat-

• During winter weather or in coastal

ed or anodized aluminum parts.

If your vehicle is damaged and

This may result in damage to the

areas, cover the bright metal parts

requires any metal repair or

with a heavier coating of wax or

protective coating and cause

replacement, be sure the body

discoloration or paint deteriora-

preservative. If necessary, coat the

shop applies anti-corrosion mate-

parts with non-corrosive petroleum

tion.

rials to the parts repaired or

jelly or other protective compound.

replaced.

7-80

Underbody maintenance

Aluminum wheel maintenance

WARNING

Corrosive materials used for ice and

The aluminum wheels are coated

snow removal and dust control may

with a clear protective finish.

After washing the vehicle, test

collect on the underbody. If these

the brakes while driving slowly

materials are not removed, acceler-

to see if they have been affected

NOTICE

ated rusting can occur on underbody

by water. If braking performance

parts such as the fuel lines, frame,

•

Do not use abrasive cleaner, pol-

is impaired, dry the brakes by

floor pan and exhaust system, even

ishing compound, solvent, or

applying them lightly while

though they have been treated with

wire brushes on aluminum

maintaining a slow forward

rust protection.

wheels.

speed.

Thoroughly flush the vehicle under-

•

Clean the wheel when it has

body and wheel openings with luke-

cooled.

warm or cold water once a month,

•

Use only a mild soap or neutral

after off-road driving and at the end

detergent, and rinse thoroughly

of each winter. Pay special attention

with water. Also, clean the

to these areas because it is difficult

wheels after driving on salted

to see all the mud and dirt. It will do

roads.

more harm than good to wet down

•

Do not wash the wheels with

the road grime without removing it.

high-speed car wash brushes.

The lower edges of doors, rocker

•

Do not use any cleaners con-

panels, and frame members have

taining acid or alkaline deter-

drain holes that should not be

allowed to clog with dirt; trapped

gents.

water in these areas can cause rust-

ing.

7-81

Maintenance

Corrosion protection

High-corrosion areas

High temperatures can also acceler-

ate corrosion of parts that are not

Protecting your vehicle from corro-

If you live in an area where your vehi-

properly ventilated so the moisture

sion

cle is regularly exposed to corrosive

can be dispersed. For all these rea-

materials, corrosion protection is

By using the most advanced design

sons, it is particularly important to

particularly important. Some of the

and construction practices to combat

keep your vehicle clean and free of

common causes of accelerated cor-

corrosion, HYUNDAI produces vehi-

mud or accumulations of other mate-

rosion are road salts, dust control

cles of the highest quality. However,

rials. This applies not only to the vis-

chemicals, ocean air and industrial

this is only part of the job. To achieve

ible surfaces but particularly to the

pollution.

the long-term corrosion resistance

underside of the vehicle.

your vehicle can deliver, the owner’s

cooperation and assistance is also

Moisture breeds corrosion

required.

To help prevent corrosion

Moisture creates the conditions in

Keep your vehicle clean

which corrosion is most likely to

Common causes of corrosion

occur. For example, corrosion is

The best way to prevent corrosion is

accelerated by high humidity, partic-

to keep your vehicle clean and free

The most common causes of corro-

ularly when temperatures are just

of corrosive materials. Attention to

sion on your vehicle are:

above freezing. In such conditions,

the underside of the vehicle is partic-

• Road salt, dirt and moisture that is

the corrosive material is kept in con-

ularly important.

allowed to accumulate underneath

tact with the car surfaces by moisture

the vehicle.

that is slow to evaporate.

• If you live in a high-corrosion area

• Removal of paint or protective

Mud is particularly corrosive

— where road salts are used, near

coatings by stones, gravel, abra-

because it is slow to dry and holds

the ocean, areas with industrial

sion or minor scrapes and dents

moisture in contact with the vehicle.

pollution, acid rain, etc.—, you

which leave unprotected metal

Although the mud appears to be dry,

should take extra care to prevent

exposed to corrosion.

it can still retain the moisture and

corrosion. In winter, hose off the

promote corrosion.

underside of your vehicle at least

once a month and be sure to clean

the underside thoroughly when

winter is over.

7-82

• When cleaning underneath the

Keep your garage dry

Interior Care

vehicle, pay particular attention to

Don't park your vehicle in a damp,

Interior general precautions

the components under the fenders

poorly ventilated garage. This cre-

and other areas that are hidden

Prevent caustic solutions such as

ates a favorable environment for cor-

from view. Do a thorough job; just

perfume and cosmetic oil, from con-

rosion. This is particularly true if you

dampening the accumulated mud

tacting the interior parts because

wash your vehicle in the garage or

rather than washing it away will

they may cause damage or discol-

drive it into the garage when it is still

accelerate corrosion rather than

oration. If they do contact the interior

wet or covered with snow, ice or

prevent it. Water under high pres-

parts, wipe them off immediately.

mud. Even a heated garage can con-

sure and steam are particularly

See the instructions for the proper

tribute to corrosion unless it is well

effective in removing accumulated

way to clean vinyl.

ventilated so moisture is dispersed.

mud and corrosive materials.

• When cleaning lower door panels,

NOTICE

Keep paint and trim in good condition

rocker panels and frame members,

• Never allow water or other liq-

be sure that drain holes are kept

Scratches or chips in the finish

uids to come in contact with

open so that moisture can escape

should be covered with "touch-up"

electrical/electronic

compo-

and not be trapped inside to accel-

paint as soon as possible to reduce

nents inside the vehicle as this

erate corrosion.

the possibility of corrosion. If bare

may damage them.

metal is showing through, the atten-

tion of a qualified body and paint

• When cleaning leather products

shop is recommended.

(steering wheel, seats etc.), use

neutral detergents or low alco-

Bird droppings are highly corrosive

hol content solutions. If you use

and may damage painted surfaces in

high alcohol content solutions

just a few hours. Always remove bird

or acid/alkaline detergents, the

droppings as soon as possible.

color of the leather may fade or

the surface may get stripped off.

7-83

Maintenance

Cleaning the upholstery and

Leather (if equipped)

CAUTION

interior trim

•

Features of seat leather

Vinyl (if equipped)

- Leather is made from the outer

•

Wrinkles or abrasions which

Remove dust and loose dirt from

skin of an animal, which goes

appear naturally from usage

vinyl with a whisk broom or vacuum

through a special process to be

are not covered by warranty.

cleaner. Clean vinyl surfaces with a

available for use. Since it is a nat-

•

Belts with metallic acces-

vinyl cleaner.

ural product, each part differs in

sories, zippers or keys inside

thickness or density.

the back pocket may damage

Fabric (if equipped)

Wrinkles may appear as a natural

the seat fabric.

result of stretching and shrinking

Remove dust and loose dirt from fab-

•

Make sure not to wet the seat.

depending on the temperature

ric with a whisk broom or vacuum

It may change the nature of

and humidity.

cleaner. Clean with a mild soap solu-

natural leather.

tion recommended for upholstery or

- The seat is made of stretchable

•

Jeans or clothes which could

carpets. Remove fresh spots imme-

fabric to improve comfort.

bleach may contaminate the

diately with a fabric spot cleaner. If

- The parts contacting the body are

surface of the seat covering

fresh spots do not receive immediate

curved and the side supporting

fabric.

attention, the fabric can be stained

area is high which provides driv-

and its color can be affected. Also, its

ing comfort and stability.

fire-resistant properties can be

- Wrinkles may appear naturally

reduced if the material is not proper-

from usage. It is not a fault of the

ly maintained.

products.

NOTICE

Using anything but recommended

cleaners and procedures may

affect the fabric's appearance and

fire-resistant properties.

7-84

•

Caring for the leather seats

•

Cleaning the leather seats

Cleaning the seat belt webbing

- Vacuum the seat periodically to

- Remove all contaminations instant-

Clean the belt webbing with any mild

remove dust and sand on the seat.

ly. Refer to instructions below for

soap solution recommended for

It will prevent abrasion or damage

removal of each contaminant.

cleaning upholstery or carpet. Follow

of the leather and maintain its qual-

the instructions provided with the

- Cosmetic products

(sunscreen,

ity.

soap. Do not bleach or re-dye the

foundation, etc.)

- Wipe the natural leather seat cover

webbing because this may weaken

Apply cleansing cream on a cloth

the seat belt.

often with dry or soft cloth.

and wipe the contaminated spot.

- Use of proper leather protector

Wipe off the cream with a wet cloth

may prevent abrasion of the cover

and remove water with a dry cloth.

Cleaning the interior window

and helps maintain the color. Be

glass

- Beverages (coffee, soft drink, etc.)

sure to read the instructions and

Apply a small amount of neutral

If the interior glass surfaces of the

consult a specialist when using

detergent and wipe until contami-

vehicle become fogged (that is, cov-

leather coating or protective agent.

nations do not smear.

ered with an oily, greasy or waxy

- Light colored (beige, cream beige)

film), they should be cleaned with

- Oil

leather is easily contaminated and

glass cleaner. Follow the directions

the stain is noticeable. Clean the

Remove oil instantly with

on the glass cleaner container.

seats frequently.

absorbable cloth and wipe with

stain remover used only for natural

- Avoid wiping with wet cloth. It may

NOTICE

leather.

cause the surface to crack.

- Chewing gum

Do not scrape or scratch the

inside of the rear window. This

Harden the gum with ice and

may result in damage to the rear

remove gradually.

window defroster grid.

7-85

Maintenance

EMISSION CONTROL SYSTEM

The emission control system of your

NOTICE

1. Crankcase Emission Control

vehicle is covered by a written limited

System

warranty. Please see the warranty

For

the

Inspection

and

The positive crankcase ventilation

information contained in the Owner’s

Maintenance Test (with Electronic

system is employed to prevent air

Handbook & Warranty Information

Stability Control (ESC) system)

pollution caused by blow-by gases

booklet in your vehicle.

•

To prevent the vehicle from mis-

being emitted from the crankcase.

Your vehicle is equipped with an

firing during dynamometer test-

This system supplies fresh filtered air

emission control system to meet all

ing, turn the Electronic Stability

to the crankcase through the air

applicable emission regulations.

Control

(ESC) system off by

intake hose. Inside the crankcase,

There are three emission control

pressing the ESC switch (ESC

the fresh air mixes with blow-by

systems, as follows.

OFF light illuminated).

gases, which then pass through the

•

After dynamometer testing is

PCV valve into the induction system.

completed, turn the ESC system

(1) Crankcase emission control sys-

back on by pressing the ESC

tem

switch again.

2. Evaporative Emission Control

(2) Evaporative emission control sys-

System Including Onboard

tem

Refueling Vapor Recovery

(3) Exhaust emission control system

(ORVR)

The Evaporative Emission Control

In order to ensure the proper func-

System is designed to prevent fuel

vapors from escaping into the atmos-

tion of the emission control systems,

it is recommended that you have

phere. The ORVR system is

designed to allow the vapors from

your vehicle inspected and main-

tained by an authorized HYUNDAI

the fuel tank to be loaded into a can-

ister while refueling at the gas sta-

dealer in accordance with the main-

tenance schedule in this manual.

tion, preventing the escape of fuel

vapors into the atmosphere.

7-86

Canister

3. Exhaust Emission Control

Engine exhaust (carbon monox-

Fuel vapors generated inside the fuel

System

ide) precautions

tank are absorbed and stored in the

The Exhaust Emission Control

• Carbon monoxide can be present

onboard canister. When the engine is

System is a highly effective system

with other exhaust fumes. If you

running, the fuel vapors absorbed in

which controls exhaust emissions

smell exhaust fumes of any kind in

the canister are drawn into the surge

while maintaining good vehicle per-

your vehicle, drive with all the win-

tank through the purge control sole-

formance.

dows fully open. Have your vehicle

noid valve.

checked and repaired immediately.

When the engine starts or fails to

start, excessive attempts to restart

WARNING

Purge Control Solenoid Valve

the engine may cause damage to the

(PCSV)

emission system.

Engine exhaust gases contain

The purge control solenoid valve is

carbon monoxide (CO). Though

controlled by the Engine Control

colorless and odorless, it is

Module

(ECM); when the engine

dangerous and could be lethal if

coolant temperature is low during

inhaled. Follow the instructions

idling, the PCSV closes so that evap-

on this page to avoid CO poi-

orated fuel is not taken into the

soning.

engine. After the engine warms-up

during ordinary driving, the PCSV

opens to introduce evaporated fuel to

the engine.

7-87

Maintenance

•

Do not operate the engine in con-

Operating precautions for cat-

WARNING

fined or closed areas

(such as

alytic converters (if equipped)

garages) any more than what is

CALIFORNIA PROPOSITION 65

necessary to move the vehicle in or

WARNING

out of the area.

Engine exhaust and a wide vari-

•

When the vehicle is stopped in an

The exhaust system and cat-

ety of automobile components

open area for more than a short

alytic converter are very hot

and parts, including compo-

time with the engine running,

during and immediately after

nents found in the interior fur-

adjust the ventilation system

(as

the engine has been running. To

nishings in a vehicle, contain or

needed) to draw outside air into the

avoid SERIOUS INJURY or

emit chemicals known to the

vehicle.

DEATH:

State of California to cause can-

•

Never sit in a parked or stopped

•

Do not park, idle, or drive the

cer and birth defects and repro-

vehicle for any extended time with

vehicle over or near flamma-

ductive harm. In addition, cer-

the engine running.

ble objects, such as grass,

tain fluids contained in vehicles

•

When the engine stalls or fails to

vegetation, paper, leaves, etc.

and certain products of compo-

start, excessive attempts to restart

A hot exhaust system can

nent wear contain or emit chem-

the engine may cause damage to

ignite flammable items under

icals known to the State of

the emission control system.

your vehicle.

California to cause cancer and

•

Keep away from the exhaust

birth defects or other reproduc-

system and catalytic convert-

tive harm.

er or you may get burned.

Also, Do not remove the heat

sink around the exhaust sys-

tem, do not seal the bottom of

the vehicle, and do not coat

the vehicle for corrosion con-

trol. It may present a fire risk

under certain conditions.

7-88

Your vehicle is equipped with a cat-

•

Do not modify or tamper with any

alytic converter emission control

part of the engine or emission con-

device.

trol system. All inspections and

adjustments must be made by an

To prevent damage to the catalytic

authorized HYUNDAI dealer.

converter and to your vehicle, take

the following precautions:

•

Avoid driving with extremely low

fuel level. If you run out of gasoline,

• Use only UNLEADED FUEL for

it could cause the engine to misfire

gasoline engines.

and result in excessive loading of

• Do not operate the vehicle when

the catalytic converter.

there are signs of engine malfunc-

tion, such as misfire or a noticeable

loss of performance.

• Do not misuse or abuse the

engine. Examples of misuse are

coasting with the engine off and

descending steep grades in gear

with the engine off.

• Do not operate the engine at high

idle speed for extended periods (5

minutes or more).

7-89

Maintenance

CALIFORNIA PERCHLORATE NOTICE

Perchlorate Material-special handling may apply, See: www.dtsc.ca.gov/hazardouswaste/perchlorate.

Notice to California Vehicle Dismantlers:

Perchlorate containing materials, such as air bag inflators, seatbelt pretensioners and keyless remote entry batteries,

must be disposed of according to Title 22 California Code of Regulations Section 67384.10 (a).

7-90

Specifications, Consumer information and Reporting safety defects

Dimensions

8-2

Engine

8-2

Bulb Wattage

8-3

Tires and Wheels

8-4

Volume and Weight

8-6

Air Conditioning System

8-6

Recommended Lubricants and Capacities

8-7

Recommended SAE viscosity number

8-9

Vehicle Identification Number (VIN)

8-10

Vehicle Certification Label

8-10

Tire Specification and Pressure Label

8-11

Engine Number

8-11

Refrigerant Label

8-11

Consumer Information

8-12

Reporting Safety Defects

8-13

Specifications, Consumer information and Reporting safety defects

DIMENSIONS

Items

in (mm)

Overall length

166.93 (4,240)

Overall width

70.86 (1,800)

Overall height

55.08 (1,399)

215/45 R17

61.46 (1,561)

Front tread

225/40 R18

60.98 (1,549)

225/40 ZR18

60.98 (1,549)

215/45 R17

62.01 (1,575)

Rear tread

225/40 R18

61.54 (1,563)

225/40 ZR18

61.54 (1,563)

Wheelbase

104.33 (2,650)

ENGINE

Items

1.6 T-GDI

2.0 MPI

Displacement

97.08 (1,591)

121.9 (1,999)

cu. in. (cc)

Bore x Stroke

3.03 x 3.06 (77 x 85.44)

3.19 x 3.82 (81 x 97)

in. (mm)

Firing order

1-3-4-2

No. of cylinders

In-line 4 cylinder

8-2

BULB WATTAGE

Light Bulb

Bulb Type

Wattage

Low (Type A)

High (Type A)

HB3

Headlamp

Low (Type B)

LED

High (Type B)

HB3

Front

Turn signal lamp

28/8W(2357A)

Turn signal lamp (Outside mirror)

LED

Daytime running lamp (DRL) / position lamp

LED

Type A

W5W

Side Marker Lamp

Type B

LED

Stop/Tail (Type A)

P21/5W

21/5

Tail (Type A)

P21/5W

Rear combination lamp

Stop/Tail (Type B)

LED

Turn signal

27W(1156A)

Rear

Back up

W16W

Type A

W5W

Side Marker Lamp

Type B

LED

High mounted stop lamp

LED

License plate lamp

W5W

Map lamp

W10W

Room lamp (without sunroof)

FESTOON

Interior

Sunvisor lamp

FESTOON

Tailgate room lamp

FESTOON

8-3

Specifications, Consumer information and Reporting safety defects

TIRES AND WHEELS

Full size tire

Inflation pressure [bar (kPa, psi)]

Normal Load

Maximum Load

High-speed driving

Wheel lug nut

Tire Size

Wheel Size

(less than 100mph or

(over 100mph or

torque [kgf•m

160km/h)

160km/h) *1

(lbf•ft, N•m)]

Front

Rear

Front

Rear

Front

Rear

215/45R17

7.0J X 17

2.3 (230, 33)

2.5 (250, 36)

11~13

225/40R18

7.5J X 18

2.3 (230, 33)

2.5 (250, 36)

(79~94, 107~127)

225/40ZR18

7.5J X 18

2.3 (230, 33)

2.5 (250, 36)

*1 : Must drive only where the speed is legal

Compact spare tire*1

Inflation pressure [bar (kPa, psi)]

Wheel lug nut torque

Tire Size

Wheel Size

[kgf•m (lbf•ft, N•m)]

Front

Rear

11~13

T125/80D16

4.0T X 16

4.2 (420, 60)

(79~94, 107~127)

*1 : If your vehicle is not equipped with a compact spare tire, your vehicle will be equipped with a Tire Mobility Kit.

8-4

NOTICE

• It is permissible to add 3 psi to the standard tire pressure specification if colder temperatures are expect-

ed soon.

Tires typically loose 1psi (7kPa) for every 12°F temperature drop. If extreme temperature variations are

expected, recheck your tire pressure as necessary to keep them properly inflated.

• An air pressure generally decreases, as you drive up to a high-altitude area above sea level. Thus, if you

plan to drive a high-altitude area, check the tire pressures in advance. If necessary, inflate them to a prop-

er level. (Air inflation per altitude : +2.4 psi/1 mile)

• Must do not exceed maximum inflation pressure shown on equipped tire sidewall.

CAUTION

When replacing tires, use the same size originally supplied with the vehicle.

Using tires of a different size can damage the related parts or not work properly.

8-5

Specifications, Consumer information and Reporting safety defects

VOLUME AND WEIGHT

Gasoline Engine

Item

1.6 T-GDI

2.0 MPI

M/T

DCT

M/T

A/T

Gross vehicle weight

3,814 (1,730)

3,858 (1,750)

3,748 (1,700)

lbs. (kg)

Luggage volume (SAE)

Behind 1st row : 44.5 (1,261)

cu. ft. (l)

Behind 2nd row : 19.9 (565)

M/T : Manual transmission

A/T : Automatic transmission

DCT : Dual clutch transmission

AIR CONDITIONING SYSTEM

Items

Weight of Volume

Classification

Refrigerant

15.87 (450) ± 0.88 (25)

R-1234yf

oz. (g)

Compressor lubricant

4.23 (120) ± 0.35 (10)

PAG

oz. (cc)

Contact an authorized HYUNDAI dealer for more details.

8-6

Была ли эта страница вам полезна?

Да!Нет

3 посетителя считают эту страницу полезной.

Hyundai Veloster (2019 year). Instruction — part 27

Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.