Hyundai Tiburon (2003 year). Manual — part 95
TIBURON(GK) > 2003 > G 2.7 V6 DOHC > Manual Transaxle System > General Information > Specifications
(M5GF1), TIBURON(GK) > 2003 > G 2.7 V6 DOHC > Manual Transaxle System > General Information >
Specifications (M5GF1)
SPECIFICATIONS (M/T)
Model
M5BF2
(5-speed)
M5GF1
(5-speed)
MFA60
(6-speed)
Engine
2.0 DOHC
2.7 DOHC
2.0 DOHC
2.7 DOHC
Gear ratio
1st
3.462
3.231
3.153
←
2nd
2.053
1.952
1.944
←
3rd
1.393
1.296
1.333
←
4th
1.061
0.943
1.055
←
5th
0.837
0.775
0.857
←
6th
-
-
0.704
←
Reverse
3.250
3.455
3.002
←
Final gear ratio
4.056
4.063
4.678
4.428
Oil quantity (
ℓ
)
2.15
2.1
2.2 ± 0.1
SERVICE STANDARD (6-SPEED M/T)
Item
Standard
Limit
Input shaft 6th gear end play
0 ~ 0.1
-
Output shaft 6th gear end play
0 ~ 0.1
-
Output shaft 6th gear bearing play
0 ~ 0.06
-
Clearance between 3rd gear and synchronizer
ring
0.9 ~ 1.45
0.7
Clearance between 4th gear and synchronizer
ring
0.9 ~ 1.45
↑
Clearance between 5th gear and synchronizer
ring
0.95 ~ 1.4
↑
Clearance between 6th gear and synchronizer
ring
0.95 ~ 1.4
↑
Clearance between reverse gear and
synchronizer ring
0.95 ~ 1.4
↑
TIGHTENG TORQUE (6-SPEED M/T)
Item
N·m
kg·cm
lb·ft
Manual transaxle case to clutch housing bolt
63 ~ 67
630 ~ 670
46 ~ 49
Drain plug
30 ~ 39
300 ~ 390
22 ~ 28
Reverse lever
11.8 ~ 15.6
118 ~ 156
8.7 ~ 11.5
Shift check plug
12.7 ~ 17.0
127 ~ 170
9.3 ~ 12.5
Shift check
22.5 ~ 25.5
225 ~ 255
16.6 ~ 18.8
Stopper bolt
26.5 ~ 30.4
26.5 ~ 304
19.6 ~ 22.4
Control shaft bolt
6.3 ~ 8.3
63 ~ 83
4.6 ~ 6.0
Shift lever mounting plate
2 ~ 3
20 ~ 30
1 ~ 2
Differential final gear bolt
112.7 ~ 127.4
1127 ~ 1274
83 ~ 94
TIBURON(GK) > 2003 > G 2.7 V6 DOHC > Manual Transaxle System > Manual Transaxle System >
Manual Transaxle > Repair procedures (M5GF1), TIBURON(GK) > 2003 > G 2.7 V6 DOHC > Manual
Transaxle System > Manual Transaxle System > Manual Transaxle > Repair procedures (M5GF1)
REMOVAL
1. Remove the engine cover.
2. Remove the battery terminal.
3. Remove the air duct.
4. Remove the battery tray.
5. Remove the air cleaner.
(1) Upper
(2) Lower
6. Remove the back-up lamp switch.
7. After removing the CKP sensor, O2 sensor and oil pressure switch wiring bracket, separate the connectors.
8. Remove the brake fluid leveling sensor connector.
9. Remove the speedometer driven gear connector.
10. Remove the clutch release cylinder mounting bolt.
11. Remove the cotter pin of the shift cable (transaxle side).
12. Remove the cotter pin of the select cable. (transaxle side)
13. Remove the clip of the shift cable (transaxle side).
14. Remove the clip of the select cable (transaxle side).
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст