Hyundai Tiburon (2003 year). Manual — part 203

While room lamp is on due to TX unlock, if another TX unlock is received, then room lamp is again on for 30
sec.
When TX lock(arm state) is received during 30 second from TX unlock, lamp is turned off immediately.
If TX lock (arm state) is received during fade out, the room lamp is switched off immediately.
Door locking functions should not be influenced by room lamp decay functions.

Time specification
T1 : 5.5±0.5 sec.
T2 : 30 sec.

15. Seat belt warning

(1) Seat belt warning indicator

Whenever the ignition 1 is turned on the seat belt warning indicator is illuminated for total time 6 seconds,
with period 0.6 sec and duty rate50%. It is not extinguished if the seat belt is sensed as fastened.
If ignition 1 is already on and the seat belt is removed, the indicator is illuminated for total time 6 seconds,
with period 0.6 sec and duty rate50%.
If ignition 1 is switched off in while the indicator is illuminated, the illumination is switched off immediately.

(2) Seat belt warning chime

Whenever the ignition 1 is turned on the seat belt warning chime is sounded for total time 6 seconds, with
period 0.9 sec and duty rate 50%. Itis silenced immediately if the seat belt is sensed as fastened.
If ignition 1 is already on and the seat belt is removed, the chime is sounded for total time 6 seconds, with
period 0.9 sec and duty rate 50%.
If ignition 1 is switched off in while the chime is sounding, the chime is switched off immediately.

Time specification
T1 : 6±1 sec.
T2 : 0.45±0.1 sec.
T3 : 0.3±0.1 sec.

16. Over speed warning chime

If the IGN2 is on, and the over speed input is grounded by cluster, chime is sounded until over speed input
by cluster is opened.

17. Folding mirror unit

If ACC is on, with each press of the folding mirror switch, the mirror fold and unfold outputs will operate

alternatively for 16±6 sec. A second press of the fold switch during an output shall cause the oppositeoutput
to occur.
If the folding mirror switch is pressed within 30 seconds after the ACC signal is removed, the mirror outputs
(folding or unfolding) will operate for 16±6 sec. If during the mirror operation, the folding mirror switch is
pressed again then the opposite operation will commence again. If after the ACC signal is removed, the
folding mirror switch is repressed within the 16±6 sec, the mirror outputs will operate for a further 16±6sec.

Time specification
T1 : 30 sec.
T2 : 16±6 sec.

18. Rear fog lamp control

When IGN1 is on and:

A. Tail lamps are on by switch or auto light

B. Headlamps are on by switch or auto light or front fog switch is on, then if rear fog switch is contacted the

rear fog lamps are turned on.

ANTI-THEFT FUNCTION

1. Arm function

Pressing the remote key lock button will result in a 0.5-second pulse issued to lock all doors.
Pressing the remote keypad unlock button once will result in a 0.5-second unlock pulse issued to unlock all
doors.
As part of the arming sequence the alarm first enters a pre-armed state before falling into the armed state.
During this pre-armed state alarm triggers are ignored. Pre-armed state can be reached from the alarmed
state, the start inhibit state or the disarmed state. Pre-Arming of the alarm can be achievedby a press of the
lock button on the remote key.
In the pre-armed state the visible and audible warnings are disabled.
This system enters the armed state if it is in the pre-armed state and, after 0.6 sec, check actuator lock and
each door, hood and tail gate close,and no door warning switch (no key in ignition).
On entering the arm state, a single flash of the hazard lamps is given, period of cycle 2 second, duty rate
50%.
If TX lock signal is received when a door, tail gate or hood is open, then lock output is given and a flash of
hazard is not given.
After the armed state is entered, if a lock signal is received then a single flash of the hazard lamps is given,
period of cycle 2 second, dutyrate 50%.
The armed state cannot be reached by locking the car with the keys.

Time specification
T1 : 0.5sec.
T2 : Max 2sec.
T3 : 1.0±0.2sec.

2. Disarm function

Disarming can be performed while the alarm is armed, or alarming, or after alarming. The alarm can be
disarmed by the following methods:

In the disarm state the visible and audible warnings are disabled and start is enabled.
In the disarm state, if TX key unlock command is received, then the hazard lamps shall be flashed twice for
period of cycle 1 sec, 50% duty rate.
Disarm state cannot be reached using the door locks by key.

Time specification
T1, T2 : 0.5±0.1sec.

A. Pressing the unlock button on the TX key. The hazard lamps shall be flashed twice for 1sec period (of

cycle), 50% duty rate.

B. If door warning switch is on, IGN1 and IGN2 are on in arm state, then arm state should be immediately

cancelled. This means that the driveris inside the vehicle before pushing TX lock, so system should not
arm.

3. Alarm function

(1) European countries

Once armed, should any door, hood or the tailgate be opened, then:

The alarm is given in the case where a door is opened with a key.

Time specification
T1 : 27±2 sec.
T2 : 0.5±0.1 sec.

A. Start relay drive output is disabled, so starting is inhibited.

B. Audible (horn) and visual (hazard lamp) warnings are issued, for 27seconds duration. The horn

warning is continuously occurring in this period.The hazard lamps operate with 1 sec period, 50 % duty
rate.

(2) Non European countries

Once armed, should any door, hood or the tailgate be opened, then:

The alarm is given in the case where a door is opened with a key.
After this time, the system maintains the start inhibit state, where no audible and visual warnings are
issued but engine starting is not possible.

Time specification
T1 : 27±2 sec.
T2 : 10±1 sec.
T3 : 0.5±0.1 sec.

A. Start relay drive output is disabled, so starting is inhibited.

B. Audible (horn) and visual (hazard lamp) warnings are issued, for three cycles, each cycle 27±1 sec.

duration on, 10±1 sec. off. The horn warning is continuously occurring during the on period. The
hazardlamps operate with 1 sec period, 50 % duty rate during the on period.

4. Operation during alarm conditions

(1) Cancelling audible alarm with the remote transmitter

CASE 1 : Door closed
During or after alarming and then closing all doors and a TX lock signal is received Then

Time specification
T1 : 0.5 sec.
T2 : 1.0±0.2 sec.
CASE 2 : Door Open
During or after alarming, with a door open and a TX lock signal is received Then

At this time, when the door is closed,

A. The lock command is executed with 0.5 sec. ON

B. Horn and start inhibition are OFF

C. Hazard lamp is flashed one time (period : 2 sec., duty: 50%, within 2 sec.)

D. The state goes to arming mode (after a lock state check)

E. The start is enabled

A. The lock command is executed with 0.5 sec. ON

B. Horn is disabled and start is enabled after confirmation of actuator lock

A. Hazard lamp is flashed one time (period : 2 sec., duty 50%)

B. The state goes to arming mode