Chrysler PT Cruiser. Manual — part 924
(5) Remove seat armrest and lumbar handle if
equipped (Fig. 32).
(6) Disengage seat back cover locking strip across
lower back cover (Fig. 33).
(7) Pull the zipper end(s) out on each side of the
seat back and unzip the front seat back cover (Fig.
34) and (Fig. 35).
Fig. 32 ARMREST SCREW
1 - ARMREST
2 - ARMREST SCREW
3 - LUMBAR HANDLE
4 - LUMBAR HANDLE SCREW
Fig. 33 FRONT SEAT LOCKING STRIP
1 - FRONT SEAT BACK COVER
2 - LOCKING STRIP
Fig. 34 FRONT SEAT BACK ZIPPER
1 - ZIPPER
Fig. 35 ZIPPING FRONT SEAT BACK COVER
1 - FRONT SEAT BACK COVER
2 - ZIP SEAT BACK COVER
23 - 154
SEATS
PT
FRONT SEAT BACK (Continued)
(8) Raise cover and remove the push pins and
board (Fig. 36)
(9) Remove upper riser shield, if equipped.
(10) Move seat cover and cushion to access the
front seat back recliner.
(11) Remove two attaching lumbar actuator screws
from the inner seat back frame (Fig. 37).
(12) Move lumbar actuator free the front seat back
recliner (Fig. 38).
(13) Remove screws attaching recliner to seat back
cushion frame on both sides (Fig. 39).
Fig. 36 FRONT SEAT BACK WITH ZIPPER
1 - PUSH PINS FASTENERS
2 - FRONT SEAT BACK COVER
Fig. 37 LUMBAR BRACKET ATTACHING SCREWS
1 - LUMBAR BRACKET ATTACHING SCREWS
Fig. 38 LUMBAR MOUNTING BRACKET
1 - LUMBAR MOUNTING BRACKET
Fig. 39 FRONT SEAT BACK ATTACHING SCREWS
1 - FRONT SEAT BACK
2 - ATTACHING SCREWS
PT
SEATS
23 - 155
FRONT SEAT BACK (Continued)
(14) Vehicle with Seat Airbag and/or Heated Seat
System, remove front seat cushion frame. Remove
two front side screws and two rear screws (Fig. 40)
and (Fig. 41).
(15) Disconnect any electrical connectors and wire
ties from the seat back that are connected under the
seat cushion, if equipped.
(16) Remove seat back frame from seat assembly.
REMOVAL - PT-27 ONLY
WARNING: BEFORE SERVICING THE SEAT BACK
THE AIRBAG SYSTEM MUST BE DISARMED. FAIL-
URE TO DO SO MAY RESULT IN ACCIDENTAL
DEPLOYMENT OF THE AIRBAG AND POSSIBLE
PERSONAL INJURY. REFER TO RESTRAINT SYS-
TEMS FOR SERVICE PROCEDURES.
CAUTION: Do not reuse the recliner assembly
attaching bolts.
(1) Remove seat from vehicle (Refer to 23 - BODY/
SEATS/SEAT - REMOVAL).
(2) Remove front seat inboard cushion side shield
(Fig. 42).
Fig. 40 FRONT SIDE ATTACHING SCREW FRONT
CUSHION
1 - FRONT SIDE ATTACHING SCREW
2 - FRONT SEAT CUSHION
Fig. 41 REAR ATTACHING SCREW - FRONT SEAT
CUSHION
1 - REAR ATTACHING SCREW
2 - FRONT SEAT CUSHION
Fig. 42 SIDE SHIELD
1 - SIDE CUSHION SHIELD
2 - SEAT BELT ATTACHING BOLT
23 - 156
SEATS
PT
FRONT SEAT BACK (Continued)
(3) Remove the seat back recliner handle/fold flat
handle and front outboard seat cushion shield (Fig.
43) and disconnect wire connectors, if equipped (Fig.
44).
(4) Remove seat armrest plug (Fig. 45).
(5) Remove seat armrest and lumbar handle if
equipped (Fig. 46).
Fig. 43 HANDLES
1 - TILT FORWARD HANDLE
2 - ATTACHING SCREWS
3 - RECLINING HANDLE
Fig. 44 SEAT SIDE SHIELD WIRE CONNECTORS
1 - WIRE CONNECTORS
Fig. 45 ARMREST PLUG
1 - ARMREST
2 - PLUG
Fig. 46 ARMREST SCREW
1 - ARMREST
2 - ARMREST SCREW
3 - LUMBAR HANDLE
4 - LUMBAR HANDLE SCREW
PT
SEATS
23 - 157
FRONT SEAT BACK (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст