Chrysler PT Cruiser. Manual — part 504
TAIL LAMP
REMOVAL
(1) Remove screw attaching tail lamp assembly to
the aperture panel (Fig. 30).
(2) Slide the lamp assembly down in the sheet
metal opening.
(3) Remove the lamp assembly from vehicle.
(4) Remove bulb socket(s) from tail lamp housing.
(5) Pull bulb(s) from socket(s).
INSTALLATION
(1) Push bulb(s) into the bulb socket(s).
(2) Install bulb socket(s) into tail lamp assembly.
Rotate the socket clockwise until fully seated.
(3) Test operation of lamps.
(4) Align the tail lamp assembly to the sheet metal
opening.
(5) Insert the lower positioning tab into the slot
and then rotate the lamp forward until the retaining
clips snap into position.
(6) Slide the lamp assembly upwards within the
opening.
(7) Install tail lamp attaching screw.
TAIL LAMP UNIT
REMOVAL
(1) Remove screw attaching tail lamp assembly to
the aperture panel (Fig. 30).
(2) Slide the lamp assembly downward in the
sheet metal opening.
(3) Remove the lamp assembly from the vehicle.
(4) Remove the bulb sockets from the lamp assem-
bly by rotating the sockets counter-clockwise until
free of the assembly.
INSTALLATION
(1) Install the bulb sockets to the lamp assembly
by rotating the sockets clockwise until fully seated.
(2) Test operation of lamps.
(3) Align the tail lamp assembly to the sheet metal
opening.
(4) Insert the lower positioning tab on the lamp
assembly into the matching slot and rotate the lamp
forward until the retaining clips snap into position.
(5) Slide the assembly upwards within the sheet
metal opening.
(6) Install the screw to hold tail lamp assembly to
the aperture panel.
Fig. 30 TAIL AND STOP LAMPS
1 - TAIL LAMP HOUSING
2 - WIRE CONNECTORS
3 - BOTTOM LOCATOR
8L - 22
LAMPS/LIGHTING - EXTERIOR
PT
LAMPS/LIGHTING - INTERIOR
TABLE OF CONTENTS
page
page
LAMPS/LIGHTING - INTERIOR
. . . . . . . . . . . . . . . . . . . . . 23
CENTER CONSOLE FLOOD LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
. . . . . . . . . . . . . . . . . . . . . . . . . 24
CENTER CONSOLE FLOOD LAMP HOUSING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . 25
COURTESY/READING LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . 25
DOME LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . 25
DOME LAMP - PT27
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . 25
DOME LAMP UNIT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . 26
CLUSTER ILLUMINATION LAMPS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . 26
REAR CARGO LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . 26
REAR CARGO LAMP UNIT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . 27
TRANS RANGE INDICATOR ILLUMINATION
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . 27
VANITY LAMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . 27
LAMPS/LIGHTING - INTERIOR
SPECIFICATIONS
INTERIOR LAMPS
CAUTION: Do not use bulbs that have a higher can-
dle power than the bulb listed in the chart below.
Damage to the lamp unit can result.
BULB APPLICATION TABLE
BULB
LAMP
CANDLE
POWER
ABS INDICATOR
LED
AIRBAG INDICATOR
LED
BRAKE SYSTEM
WARNING
INDICATOR
LED
CLIMATE
CONTROLS
6233137
0.95
CONSOLE FLOOD
LAMP
T37
0.5
BULB
LAMP
CANDLE
POWER
CONSOLE
TRANSMISSION
RANGE INDICATOR
(PRNDL)
T194
2.0
DOME LAMP
T579
9.0
DOME LAMP WITH
INTRUSION
SENSOR - EXPORT
T578
9.0
FRONT FOG LAMP
INDICATOR
LED
HIGH BEAM
INDICATOR
PC74
0.7
INSTRUMENT
CLUSTER
ILLUMINATION
PC74
0.7
LOW FUEL
INDICATOR
LED
LOW OIL
PRESSURE
INDICATOR
LED
MALFUNCTION
INDICATOR LIGHT
LED
MAP/READING
LAMP
T1037
4.4
PT
LAMPS/LIGHTING - INTERIOR
8L - 23
BULB
LAMP
CANDLE
POWER
REAR CARGO
LAMP
T904
4.0
SEAT BELT
INDICATOR
LED
SECURITY ALARM
INDICATOR
LED
TRAC OFF
INDICATOR
LED
TURN SIGNAL
INDICATOR
T74
0.7
VISOR VANITY
6501966
4.4
VOLTAGE
INDICATOR
LED
All the interior bulbs utilize a brass or glass wedge
base. Bulbs with aluminum bases are not approved
and should not be used.
CENTER CONSOLE FLOOD
LAMP
REMOVAL
(1) Open hood.
(2) Disconnect and isolate the battery negative
cable.
(3) Insert a small screwdriver into notch by clip
(Fig. 1)and gently pry out unit.
(4) Slide back rear cover to expose bulb.
(5) Replace bulb.
INSTALLATION
(1) Insert new bulb.
(2) Gently secure bulb back into slot.
NOTE: When installing the retainer, ensure that the
forward tabs are inserted properly into the slots in
the instrument panel.
(3) Connect the battery negative cable.
(4) Close hood.
(5) Verify vehicle and system operation.
Fig. 1 CENTER CONSOLE FLOOD LAMP LOCATION
1 - CENTER CONSOLE FLOOD LAMP
8L - 24
LAMPS/LIGHTING - INTERIOR
PT
LAMPS/LIGHTING - INTERIOR (Continued)
CENTER CONSOLE FLOOD
LAMP HOUSING
REMOVAL
(1) Using a flat blade tool, remove console flood
lamp from the lower center console (Fig. 2).
(2) Disconnect wire connector.
(3) Remove console flood lamp housing.
INSTALLATION
(1) Place console flood lamp housing near opening
and connect the wire connector (Fig. 2).
(2) Test lamp.
(3) Place console flood lamp into position and
apply hand pressure to snap lamp into position.
COURTESY/READING LAMP
REMOVAL
(1) Insert a trim stick between the lamp bezel and
courtesy/readinglamp lens.
(2) Carefully swing down one side the lamp lens.
(3) Remove bulb from lamp socket.
INSTALLATION
(1) Push bulb in socket and snap into place.
(2) Position lens on lamp and snap into place.
DOME LAMP
REMOVAL
(1) Insert a trim stick between the lamp unit and
the lens.
(2) Carefully swing down one side the lamp lens.
(3) Remove lamp from lamp unit socket.
INSTALLATION
(1) Push lamp in socket and snap into place.
(2) Position lens on lamp unit and snap into place.
DOME LAMP - PT27
REMOVAL
(1) Open hood.
(2) Disconnect and isolate the battery negative
cable.
(3) Using a trim stick (special tool #C-4755) or
equivalent, gently pry off the dome lamp cover from
the sport bar (Fig. 3).
(4) Disconnect the dome lamp from the connector
(Fig. 3).
(5) Remove lamp from vehicle.
INSTALLATION
(1) Remove lamp from vehicle.
(2) Connect the dome lamp to the connector (Fig.
3).
(3) Position the dome lamp cover on the sport bar
(Fig. 3) and firmly push on cover to snap into place.
The lens must be orientated correctly for proper fit.
(4) Connect the battery negative cable.
(5) Open hood.
(6) Verify vehicle and system operation.
Fig. 2 LOWER INSTRUMENT PANEL CENTER
STACK
1 - CONSOLE FLOOD LAMP
2 - INSERT SMALL FLAT TOOL
Fig. 3 DOME LAMPS - REMOVE/INSTALL
1 - SPORT BAR CENTER MOULDING
2 - DOME LAMP ELECTRICAL CONNECTORS
3 - DOME LAMPS
4 - DOME LAMPS COVERS
PT
LAMPS/LIGHTING - INTERIOR
8L - 25
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст