Chrysler PT Cruiser. Manual — part 847
(58) Remove low/reverse spring compressor tool
and low reverse piston return spring (Fig. 80).
(59) Using a suitable punch , drive out park guide
bracket pivot shaft plug (Fig. 81).
(60) Using ordinary pliers, remove pivot shaft and
guide bracket assembly (Fig. 82).
(61) Inspect guide bracket components for exces-
sive wear and replace if necessary (Fig. 83).
NOTE: The Low/Reverse Clutch Piston has bonded
seals which are not individually serviceable. Seal
replacement requires replacement of the piston
assembly.
Fig. 80 Low/Reverse Piston Return Spring
1 - LOW/REVERSE PISTON RETURN SPRING
2 - PISTON
Fig. 81 Remove Anchor Shaft and Plug
1 - GUIDE BRACKET ANCHOR SHAFT
2 - PIVOT SHAFT
3 - ANCHOR SHAFT PLUG
Fig. 82 Pivot Shaft and Guide Bracket
1 - ANTIRACHET SPRING
2 - GUIDE BRACKET
3 - PIVOT SHAFT
4 - PAWL
Fig. 83 Guide Bracket Disassembled
1 - ANTIRATCHET SPRING
2 - GUIDE BRACKET
3 - SPLIT SLEEVE
4 - SPACER
5 - PAWL
6 - STEPPED SPACER
21 - 342
41TE AUTOMATIC TRANSAXLE
PT
41TE AUTOMATIC TRANSAXLE (Continued)
(62) Remove low/reverse clutch piston (Fig. 84).
(63) Remove
low/reverse
piston
retainer-to-case
screws (Fig. 85).
(64) Remove low/reverse piston retainer (Fig. 86).
(65) Remove
low/reverse
piston
retainer-to-case
gasket (Fig. 87).
Fig. 84 Remove Low/Reverse Clutch Piston
1 - LOW/REVERSE CLUTCH PISTON
2 - BONDED SEAL
3 - BONDED SEAL
Fig. 85 Remove Piston Retainer Attaching Screws
1 - LOW/REVERSE CLUTCH PISTON RETAINER
2 - SCREWDRIVER
3 - TORX-LOC SCREWS
Fig. 86 Remove Piston Retainer
1 - LOW/REVERSE CLUTCH PISTON RETAINER
2 - GASKET
Fig. 87 Remove Piston Retainer Gasket
1 - GASKET HOLES MUST LINE UP
2 - LOW/REVERSE CLUTCH PISTON RETAINER GASKET
PT
41TE AUTOMATIC TRANSAXLE
21 - 343
41TE AUTOMATIC TRANSAXLE (Continued)
(66) Using a hammer and suitable drift, drive out
inner output bearing cup (Fig. 88).
(67) Using tool 6062, remove outer output bearing
cup (Fig. 89).
ASSEMBLY
CAUTION:
The
cooler
bypass
valve
must
be
replaced if transaxle failure has occurred. Do not
attempt to reuse or clean old valve.
NOTE: If transaxle is being overhauled (clutch
and/or seal replacement), the TCM/PCM Quick Learn
procedure must be performed. (Refer to 8 - ELEC-
TRICAL/ELECTRONIC CONTROL MODULES/TRANS-
MISSION
CONTROL
MODULE
-
STANDARD
PROCEDURE)
(1) Install both output bearing cups using Tool
5050 (Fig. 90).
(2) Install low/reverse piston retainer gasket (Fig.
91). Make sure gasket holes line up with case.
Fig. 88 Remove Output Bearing Inner Cup
1 - OUTPUT BEARING CUPS (REPLACE IN PAIRS)
2 - HAMMER
3 - BRASS DRIFT
Fig. 89 Remove Output Bearing Outer Cup
1 - TOOL 6062
Fig. 90 Install Both Output Bearing Cups
1 - OUTPUT BEARING CUPS
2 - WRENCHES
3 - TOOL 5050
Fig. 91 Install Piston Retainer Gasket
1 - GASKET HOLES MUST LINE UP
2 - LOW/REVERSE CLUTCH PISTON RETAINER GASKET
21 - 344
41TE AUTOMATIC TRANSAXLE
PT
41TE AUTOMATIC TRANSAXLE (Continued)
(3) Install low/reverse piston retainer (Fig. 92).
(4) Install low/reverse piston retainer-to-case bolts
(Fig. 93) and torque to 5 N·m (45 in. lbs.).
NOTE: The Low/Reverse Clutch Piston has bonded
seals which are not individually serviceable. Seal
replacement requires replacement of the piston
assembly.
(5) Install low/reverse clutch piston (Fig. 94).
(6) Assemble park guide bracket assembly (Fig.
96) (Fig. 95).
Fig. 92 Install Piston Retainer
1 - LOW/REVERSE CLUTCH PISTON RETAINER
2 - GASKET
Fig. 93 Install Piston Retainer Attaching Screws
1 - LOW/REVERSE CLUTCH PISTON RETAINER
2 - SCREWDRIVER
3 - TORX-LOC SCREWS
Fig. 94 Install Low/Reverse Clutch Piston
1 - LOW/REVERSE CLUTCH PISTON
2 - BONDED SEAL
3 - BONDED SEAL
Fig. 95 Guide Bracket Disassembled
1 - ANTIRATCHET SPRING
2 - GUIDE BRACKET
3 - SPLIT SLEEVE
4 - SPACER
5 - PAWL
6 - STEPPED SPACER
PT
41TE AUTOMATIC TRANSAXLE
21 - 345
41TE AUTOMATIC TRANSAXLE (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст