Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 688
REAR
(1) Partially raise convertible top.
(2) Remove push in fasteners attaching weather-
strip to retainer.
(3) Separate weatherstrip from vehicle (Fig. 26).
INSTALLATION
FRONT
(1) Position weatherstrip on vehicle.
(2) Install push in fasteners into retainer channel,
aligning embossment on back side of weatherstrip to
corner of retainer.
(3) Lower convertible top.
(4) Secure convertible top.
CENTER
(1) Position weatherstrip on vehicle.
(2) Install push in fasteners into retainer channel,
aligning embossment on back side of weatherstrip to
corner of retainer.
(3) Lower convertible top.
(4) Secure convertible top.
REAR
(1) Position weatherstrip on vehicle.
(2) Install push in fasteners into retainer channel,
aligning embossment on back side of weatherstrip to
corner of retainer.
(3) Push weatherstrip into retainer channel, align-
ing embossment on backside of weatherstrip to cor-
ner of retainer.
(4) Lower convertible top.
(5) Secure convertible top.
Fig. 26 Rear Side Rail
1 - CONVERTIBLE TOP
2 - REAR SIDE RAIL WEATHERSTRIP
3 - QUARTER PANEL
JR
WEATHERSTRIP/SEALS
23 - 149
SIDE RAIL WEATHERSTRIP (Continued)
BODY STRUCTURE
TABLE OF CONTENTS
page
page
GAP AND FLUSH
SPECIFICATIONS - BODY GAP AND FLUSH
MEASUREMENTS - JR-27 . . . . . . . . . . . . . . 150
SPECIFICATIONS - BODY GAP AND FLUSH
MEASUREMENTS - JR-41 . . . . . . . . . . . . . . 152
OPENING DIMENSIONS
DIMENSION - JR-27 . . . . . . . . . . . . . . . . . . . 154
DIMENSIONS - JR-41 . . . . . . . . . . . . . . . . . 157
SEALER LOCATIONS
SPECIFICATIONS - SEALER LOCATIONS -
JR-27 AND JR-41 . . . . . . . . . . . . . . . . . . . . . 160
SPECIFICATIONS - SEALER LOCATIONS -
JR-27 ONLY . . . . . . . . . . . . . . . . . . . . . . . . . 164
SPECIFICATIONS - SEALER LOCATIONS -
JR-41 ONLY . . . . . . . . . . . . . . . . . . . . . . . . . 180
STRUCTURAL ADHESIVE LOCATIONS
ADHESIVE LOCATIONS - JR-27 . . . . . . . . . . 196
ADHESIVE LOCATIONS - JR-41 . . . . . . . . . . 207
WELD LOCATIONS
SPECIFICATIONS - WELD LOCATIONS -
JR-27 AND JR-41 . . . . . . . . . . . . . . . . . . . . . 214
SPECIFICATIONS - WELD LOCATIONS -
JR-27 ONLY . . . . . . . . . . . . . . . . . . . . . . . . . 248
SPECIFICATIONS - WELD LOCATIONS -
JR-41 ONLY . . . . . . . . . . . . . . . . . . . . . . . . . 271
GAP AND FLUSH
SPECIFICATIONS
SPECIFICATIONS - BODY GAP AND FLUSH
MEASUREMENTS - JR-27
INDEX
DESCRIPTION
FIGURE
BODY GAP AND FLUSH
1
23 - 150
BODY STRUCTURE
JR
Fig. 1 BODY GAP AND FLUSH
JR
BODY STRUCTURE
23 - 151
GAP AND FLUSH (Continued)
LOCATION
GAP
FLUSH
1
Fascia to Hood
6.0 Blending to 8.0 ± 2.5
Parallel within 2.5
1.6 Under Flush ± 2.5
Consistent within 2.5
2
Headlamp to Hood
8.0 ± 2.5 Parallel within 2.0
3
Hood to Fender
4.0 ± 1.0 Parallel within 1.5
Flush ± 1.5 Consistent within
2.0
4
Fender to Door
5.0 ± 1.0 Parallel within 2.5
0.8 Over Flush ± 1.5
Consistent within 2.0
5
Doors to Body Side Sill
6.0 ± 1.5 Parallel within 2.0
6.0 Under Flush ± 1.5
Consistent within 2.5
6
Door to Quarter Panel
4.0 ± 1.0 Parallel within 1.5
Flush ± 1.5 Consistent within
2.0
7
Fuel Filter Door to Quarter Panel
3.0 ± 0.75 Uniform within 1.0
Flush ± 1.0
8
Deck Lid Molding to Deck Lid
4.5 ± 2.0 Parallel within 2.5
9
Deck Lid to Quarter Panel
4.0 ± 1.0 Parallel within 1.0
Flush ± 1.5 Consistent within
1.5
10
Tail Lamp to Deck Lid
5.0 Blending to 5.5 ± 1.5 LH
& RH to be within 2.0
11
Fascia to Deck Lid
7.0 ± 2.0 Parallel Within 1.5
12
Deck Lid Applique to Fascia
9.0 ± 2.0 Parallel within 2.0
NOTE: ALL MEASUREMENTS ARE IN mm
SPECIFICATIONS - BODY GAP AND FLUSH
MEASUREMENTS - JR-41
INDEX
DESCRIPTION
FIGURE
BODY GAP AND FLUSH MEASUREMENTS
2
23 - 152
BODY STRUCTURE
JR
GAP AND FLUSH (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст