Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 15
TEST
ACTION
APPLICABILITY
3
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
Disconnect the Load Tool from the Driver Seat Belt Tensioner connector.
Disconnect the Airbag Control Module Connector(s).
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool ACM Adaptor to the Airbag Control Module
connector(s).
Measure the resistance of the Driver SBT Line 1 and Line 2 circuits between the
Load Tool Adapter and the Driver SBT connector.
Is the resistance below 1.0 ohms on both circuit?
All
Yes
→ Go To 4
No
→ Repair open or high resistance in Driver Seat Belt Tensioner Line
1 Line 2 circuits.
Perform __AIRBAG VERIFICATION TEST - VER 1.
4
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT,
PERSONAL INJURY OR DEATH, .
If there are no possible causes remaining, view repair.
All
Repair:
Replace the Airbag Control Module in accordance with the Service
information.
Perform __AIRBAG VERIFICATION TEST - VER 1.
45
AIRBAG
DRIVER SEAT BELT TENSIONER CIRCUIT OPEN —
Continued
TEST
ACTION
APPLICABILITY
5
With the DRBIII
t, record and erase all DTC’s from all Airbag modules.
If equipped with Passenger Airbag On - Off switch, read the DTC’s in all switch
positions.
If any ACTIVE codes are present they must be resolved before diagnosing any stored
codes.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
Using the wiring diagram/schematic as a guide, inspect the wiring and connectors.
Look for chaffed, pierced, pinched, or partially broken wires and broken, bent, pushed
out, spread, corroded, or contaminated terminals.
The following additional checks may assist you in identifying a possible intermittent
problem.
Reconnect any disconnected components and harness connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t monitor active codes as you work through the following steps.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, MAINTAIN A SAFE
DISTANCE FROM ALL AIRBAGS WHILE PERFORMING THE FOLLOWING
STEPS.
Wiggle the wiring harness and connectors of the related airbag circuit or component.
If codes are related to the Driver Airbag circuits, rotate the steering wheel from stop
to stop.
IF only stored codes return continue the test until the problem area has been isolated
In the previous steps you have attempted to recreate the conditions responsible for
setting active DTC in question.
Are any ACTIVE DTCs present?
All
Yes
→ Select appropriate symptom from Symptom List.
No
→ No problem found at this time. Erase all codes before returning
vehicle to customer.
46
AIRBAG
DRIVER SEAT BELT TENSIONER CIRCUIT OPEN —
Continued
Symptom:
DRIVER SEAT BELT TENSIONER CIRCUIT SHORT
When Monitored and Set Condition:
DRIVER SEAT BELT TENSIONER CIRCUIT SHORT
When Monitored:
With the ignition on the ACM monitors the resistance of the Driver
Seat Belt Tensioner circuits
Set Condition:
The ACM has detected low resistance in the Driver Seat Belt Tensioner
circuits.
POSSIBLE CAUSES
DRIVER SEAT BELT TENSIONER SHORT
DRIVER SEAT BELT TENSIONER LINE 1 SHORT TO LINE 2
ACM, DRIVER SEAT BELT TENSIONER CIRCUIT SHORT
STORED CODE OR INTERMITTENT CONDITION
ACTIVE CODE PRESENT
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
NOTE: Ensure the battery is fully charged.
NOTE: For the purpose of this test, the AECM and ORC modules will be
referred to as an ACM.
SELECT ACTIVE or STORED DTC:
All
ACM - ACTIVE DTC
ACM - STORED DTC
NOTE: When reconnecting airbag system components the Ignition must be
turned off and the Battery must be disconnected.
2
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
Disconnect the Driver Seat Belt Tensioner connector.
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool to the Driver Seat Belt Tensioner connector.
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
ON, THEN RECONNECT THE BATTERY.
With the DRBIII
t, read active Airbag Control Module DTC’s.
Does the DRBIII
t display DRIVER SEAT BELT TENSIONER CIRCUIT SHORT?
All
Yes
→ Go To 3
No
→ Replace Driver Seat Belt Tensioner in accordance with the Service
Information.
Perform __AIRBAG VERIFICATION TEST - VER 1.
47
AIRBAG
TEST
ACTION
APPLICABILITY
3
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN IGNITION
OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BEFORE
PROCEEDING.
Disconnect the Load Tool from the Driver Seat Belt Tensioner connector.
Disconnect the Airbag Control Module connector(s).
NOTE: Check connectors - Clean and repair as necessary.
Connect the appropriate Load Tool ACM Adaptor to the Airbag Control Module
connector(s).
Measure the resistance between the Driver SBT Line 1 and Line 2 circuit at the
Driver SBT connector.
Is the resistance below 10K Ohms?
All
Yes
→ Repair Driver Seat Belt Tensioner Line 1 circuit short to Driver
Seat Belt Tensioner Line 2 circuit.
Perform __AIRBAG VERIFICATION TEST - VER 1.
No
→ Go To 4
4
WARNING: TO AVOID PERSONAL INJURY OR DEATH, TURN THE IGNI-
TION OFF, DISCONNECT THE BATTERY AND WAIT TWO MINUTES BE-
FORE PROCEEDING.
WARNING: IF THE AIRBAG CONTROL MODULE IS DROPPED AT ANY
TIME, IT MUST BE REPLACED. FAILURE TO TAKE THE PROPER PRE-
CAUTIONS COULD RESULT IN ACCIDENTAL AIRBAG DEPLOYMENT
AND PERSONAL INJURY OR DEATH.
If there are no possible causes remaining, view repair.
All
Repair:
Replace the Airbag Control Module in accordance with the Service
Information.
Perform __AIRBAG VERIFICATION TEST - VER 1.
48
AIRBAG
DRIVER SEAT BELT TENSIONER CIRCUIT SHORT —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст