Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 222
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Remove the ASD Relay from the PDC.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K25) ASD Output circuit from the PDC to the
appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the open in the (K25) ASD Relay Output circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
4
NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.
All
Repair
Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
5
Turn the ignition off.
Install a substitute relay in place of the ASD Relay.
Ignition on, engine not running.
With the DRBIII
t, erase DTCs.
Attempt to start the engine.
With the DRBIII
t, read DTCs.
Does the DTC reset?
All
Yes
→ Go To 6
No
→ Replace the ASD Relay.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
6
Turn the ignition off.
Remove the ASD Relay from the PDC.
Measure the voltage of the (A14) Fused B+ circuit in the PDC.
Is the voltage above 11.0 volts?
All
Yes
→ Go To 7
No
→ Repair the (A14) Fused B+ circuit. Inspect the related fuse and
repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
265
DRIVEABILITY - NGC
P0688-ASD RELAY SENSE CIRCUIT LOW —
Continued
TEST
ACTION
APPLICABILITY
7
Turn the ignition off.
Remove the ASD Relay from the PDC.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the ASD Output circuit from the PDC to the each of the
ASD Relay Output circuits at the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 8
No
→ Repair the open in the ASD Relay Output circuit(s).
Perform POWERTRAIN VERIFICATION TEST VER - 5.
8
NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.
All
Repair
Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
266
DRIVEABILITY - NGC
P0688-ASD RELAY SENSE CIRCUIT LOW —
Continued
Symptom:
P0700-TRANSMISSION CONTROL SYSTEM/READ TRANSMISSION
DTCS ON THE DRBIII
t
TEST
ACTION
APPLICABILITY
1
This is an informational DTC letting you know that a DTC(s) is stored in the
Transmission Control Module.
Erase this DTC from the PCM after all Transmission DTC(s) have been repaired.
Using the DRBIII
t, read the Transmission Controller DTC and refer to the
Transmission Category and perform the appropriate symptom.
PCM Diagnostic Information complete.
All
Continue
Test Complete.
267
DRIVEABILITY - NGC
Symptom:
P0850-PARK/NEUTRAL SWITCH PERFORMANCE
When Monitored and Set Condition:
P0850-PARK/NEUTRAL SWITCH PERFORMANCE
When Monitored:
Continuously with the transmission in Park, Neutral, or Drive and
NOT in Limp-in mode.
Set Condition:
The PCM detects an incorrect Park/Neutral switch state for a given mode
of vehicle operation. Two Trip Fault.
POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
TRANSMISSION DTC(S)
PCM
TEST
ACTION
APPLICABILITY
1
NOTE: Check the TCM for DTCs. Diagnose any DTCs related to the TRS that
may have set in the TCM.
Ignition on, engine not running.
NOTE: Before continuing, ensure that communication can be established
with the TCM. If the DRBIII
t can not communicate with the TCM refer to
the Communication Category and preform the appropriate symptom.
With the DRBIII
t, read PCM DTCs and record the related Freeze Frame data.
Is the Good Trip displayed and equal to zero?
All
Yes
→ Go To 2
No
→ Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
2
Turn the ignition on.
With the DRBIII
t, check the Transmission DTCs.
Are there any Transmission DTCs present?
All
Yes
→ Refer to the appropriate Transmission DTC in the Transmission
category.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No
→ NOTE: Before continuing, check the PCM harness connector
terminals for corrosion, damage, or terminal push out. Repair as
necessary. Replace and program the Powertrain Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
268
DRIVEABILITY - NGC
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст