Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 474
any internal circuit of the PDC or the PDC housing
is faulty or damaged, the entire PDC and headlamp/
dash wire harness unit must be replaced.
(1) Disconnect and isolate the battery negative
cable.
(2) Remove the Air Inlet System (housing and res-
onator).
(3) Disconnect each of the wire harness connectors.
(4) Remove the fasteners that secure each of the
wire harness ground eyelets to the vehicle body and
chassis components.
(5) Disengage each of the retainers that secure the
engine compartment wire harness to the vehicle body
and chassis components.
(6) Remove the nut retaining the PDC to its
mounting bracket.
(7) Remove the PDC and the wire harness from
the engine compartment as a unit.
INSTALLATION
(1) Position the PDC in the engine compartment.
(2) Align the PDC mounting slots with the blades
on the PDC mounting bracket.
(3) Install the mounting nut onto the PDC.
(4) Route the wire harness from the PDC through
the engine compartment, engaging each of the har-
ness retainers to the mounting provisions in the
vehicle body and chassis components.
(5) Install and tighten the fasteners that secure
each of the engine compartment wire harness ground
eyelets to the vehicle body and chassis components.
(6) Reconnect each of the wire harness connectors.
(7) Connect the battery negative cable.
POWER OUTLET
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Remove left side console lower cover.
(3) Disconnect wire harness connectors from power
outlet.
(4) Twist power outlet retainer from the back of
power outlet.
(5) Remove power outlet.
INSTALLATION
(1) Install power outlet to instrument panel.
(2) Install retainer to power outlet.
(3) Connect wire harness connectors.
(4) Install left side console lower cover.
(5) Connect battery negative cable.
JR
8W-97 POWER DISTRIBUTION
8W - 97 - 5
POWER DISTRIBUTION CENTER (Continued)
ENGINE
TABLE OF CONTENTS
page
page
ENGINE 2.7L DOHC . . . . . . . . . . . . . . . . . . . . . . 150
ENGINE 2.0L DOHC
TABLE OF CONTENTS
page
page
ENGINE 2.0L DOHC
. . . . . . . . . . . . . . . . . . . . . . . . . . 3
ENGINE DIAGNOSIS - INTRODUCTION
ENGINE DIAGNOSIS - PERFORMANCE
CYLINDER COMPRESSION PRESSURE TEST
LEAKAGE TEST . . . . . . . . . . . . . . . . . . . . . . . 9
THREADS . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
FORM-IN-PLACE GASKETS AND SEALERS
ENGINE GASKET SURFACE PREPARATION
MEASURING BEARING CLEARANCE USING
PLASTIGAGE . . . . . . . . . . . . . . . . . . . . . . . . 12
ENGINE CORE AND OIL GALLERY PLUGS
INSTALLATION - ENGINE ASSEMBLY
. . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
. . . . . . . . . . . . . . . . . . . 21
AIR CLEANER ELEMENT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . 25
AIR CLEANER HOUSING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . 25
CYLINDER HEAD
. . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
. . . . . . . . . . . . . . . . . . . . . . . . . . 27
CAMSHAFT OIL SEAL(S)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . 30
CAMSHAFT(S)
. . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . . 31
. . . . . . . . . . . . . . . . . . . . . . . . . 31
CYLINDER HEAD COVER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . . 32
. . . . . . . . . . . . . . . . . . . . . . . . . 32
HYDRAULIC LASH ADJUSTERS
DIAGNOSIS . . . . . . . . . . . . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . . . 34
INTAKE/EXHAUST VALVES & SEATS
. . . . . . . . . . . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . . . . . 34
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
ROCKER ARMS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
. . . . . . . . . . . . . . . . . . . . . . . . . . 35
. . . . . . . . . . . . . . . . . . . . . . . . . 35
VALVE SPRINGS AND SEALS
. . . . . . . . . . . . . . . . . . 35
. . . . . . . . . . . . . . . . . 36
. . . . . . . . . . . . . . . . . . . . . . . . . . 36
. . . . . . . . . . . . . . . . . . 36
. . . . . . . . . . . . . . . . . 36
JR
ENGINE
9 - 1
ENGINE BLOCK
. . . . . . . . . . . . . . . . . . . . . . . . . 37
. . . . . . . . . . . . . . 37
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
. . . . . . . . . . . . . . . . . . . . . . . . . . 38
CRANKSHAFT
STANDARD PROCEDURE - CRANKSHAFT
. . . . . . . . . . . . . . . . . . . . . . . . . . . 38
. . . . . . . . . . . . . . . . 39
. . . . . . . . . . . . . . . . . . . . . . . . . . 40
CRANKSHAFT OIL SEAL - FRONT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
. . . . . . . . . . . . . . . . . . . . . . . . . 43
CRANKSHAFT OIL SEAL - REAR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
. . . . . . . . . . . . . . . . . . . . . . . . . 45
PISTON & CONNECTING ROD
. . . . . . . . . . . . . . . . . . . . . . . . . 45
STANDARD PROCEDURE - PISTON TO
. . . . . . . . . . . . . . 46
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
. . . . . . . . . . . . . . . . . . . . . . . . . 48
CONNECTING ROD BEARINGS
PISTON RINGS
STANDARD PROCEDURE - PISTON RING -
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
. . . . . . . . . . . . . . . . . . . . . . . . . 49
STRUCTURAL COLLAR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
. . . . . . . . . . . . . . . . . . . . . . . . . 51
VIBRATION DAMPER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
. . . . . . . . . . . . . . . . . . . . . . . . . 51
ENGINE MOUNTING
LEFT MOUNT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
. . . . . . . . . . . . . . . . . . . . . . . . . 52
RIGHT MOUNT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
. . . . . . . . . . . . . . . . . . . . . . . . . 53
FRONT MOUNT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
. . . . . . . . . . . . . . . . . . . . . . . . . 53
REAR MOUNT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
. . . . . . . . . . . . . . . . . . . . . . . . . 54
LUBRICATION
. . . . . . . . . . . . . . . . . . . . . . . . . 55
. . . . . . . . . . . . . . . . . . . . . . . . . . . 55
OIL
STANDARD PROCEDURE - ENGINE OIL
AND FILTER CHANGE . . . . . . . . . . . . . . . . . . 56
OIL FILTER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
. . . . . . . . . . . . . . . . . . . . . . . . . 58
OIL FILTER ADAPTER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
. . . . . . . . . . . . . . . . . . . . . . . . . 58
OIL PAN
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
. . . . . . . . . . . . . . . . . . . . . . . . . 58
OIL PRESSURE SENSOR/SWITCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
. . . . . . . . . . . . . . . . . . . . . . . . . 59
OIL PUMP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
. . . . . . . . . . . . . . . . . . . . . . . . . 60
. . . . . . . . . . . . . . . . . . . . . . . . . . 60
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
. . . . . . . . . . . . . . . . . . . . . . . . . 62
INTAKE MANIFOLD
. . . . . . . . . . . . . . 63
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
. . . . . . . . . . . . . . . . . . . . . . . . . . 64
. . . . . . . . . . . . . . . . . . . . . . . . . 64
EXHAUST MANIFOLD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
. . . . . . . . . . . . . . . . . . . . . . . . . . 65
. . . . . . . . . . . . . . . . . . . . . . . . . 65
VALVE TIMING
TIMING BELT COVER(S)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
. . . . . . . . . . . . . . . . . . . . . . . . . 67
TIMING BELT AND SPROCKETS
. . . . . . . . . . . . . . . 68
. . . . . . . . . . . . . . 69
. . . . . . . . . . . . . . 69
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
. . . . . . . . . . . . . . 70
. . . . . . . . . . . . . . . 70
TIMING BELT TENSIONER & PULLEY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
. . . . . . . . . . . . . . . . . . . . . . . . . 72
9 - 2
ENGINE 2.0L DOHC
JR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст