Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 83
TEST
ACTION
APPLICABILITY
2
Turn the ignition off.
Disconnect the Body Control Module C2 harness connector.
Using a 12-volt test light, back probe between the Recirculation Door Driver circuit
and the Common Door Driver circuit in the BCM C2 harness connector.
Reconnect the Body Control Module C2 harness connector.
Turn the ignition on.
With the DRBIII
t, select Body, Body Computer, System Tests then Actuate Mode
Doors.
Select Recirc Door.
While observing the test light, press and hold the DRB right arrow key for several
seconds.
While observing the test light, press and hold the DRB left arrow key for several
seconds.
Is the test light on while the right and left arrow keys are pressed?
All
Yes
→ Go To 3
No
→ Replace and program the Body Control Module in accordance
with the Service Information.
Calibration must be performed after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition off.
Disconnect the Body Control Module C2 harness connector.
Disconnect the Recirculation Door Actuator harness connector.
Measure the resistance of the Recirculation Door Driver circuit between the BCM C2
harness connector and the Recirculation Door Actuator harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the Recirculation Door Driver circuit for an open.
Calibration must be performed after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.
4
Turn the ignition off.
Disconnect the Body Control Module C2 harness connector.
Disconnect the Recirculation Door Actuator harness connector.
Measure the resistance of the Common Door Driver circuit between the BCM C2
harness connector and the Recirculation Door Actuator harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Inspect for missing & broken actuator linkage. Check door for
binding & loss of full range. Inspect housing for missing or broken
stops. Repair as necessary. If linkage and door are okay, replace
Recirc Door Actuator in accordance with Service Info.
Calibration must be performed after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair the Common Door Driver circuit for an open.
Calibration must be performed after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.
317
HEATING & A/C
RECIRCULATION DOOR STALL TEST FAILURE - ATC & MTC —
Continued
TEST
ACTION
APPLICABILITY
5
Turn the ignition off.
NOTE: Visually inspect the related wiring harness and circuits. Look for
any chafed, pierced, pinched, or partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
NOTE: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?
All
Yes
→ Repair as necessary.
Calibration must be performed after repair/replacement is com-
pleted.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
318
HEATING & A/C
RECIRCULATION DOOR STALL TEST FAILURE - ATC & MTC —
Continued
Symptom:
SUN LOAD SENSOR FAILURE - ATC
When Monitored and Set Condition:
SUN LOAD SENSOR FAILURE - ATC
When Monitored:
With the ignition on.
Set Condition:
The BCM detects an abnormally low voltage on the sun sensor signal.
POSSIBLE CAUSES
SUN SENSOR LOW
SUN SENSOR SIGNAL CIRCUIT SHORTED TO GROUND
SUN SENSOR SIGNAL CIRCUIT SHORTED TO SENSOR GROUND
BODY CONTROL MODULE - SUN SENSE LOW
TEST
ACTION
APPLICABILITY
1
NOTE: It is advisable to perform the ATC System Test before attempting to
diagnose this trouble code.
Turn the ignition off.
Disconnect the Sun Sensor/VTSS LED harness connector.
Turn the ignition on.
With the DRBIII
t in Sensor Display, read the Sun Sensor voltage.
Is the voltage below 0.2 volts?
All
Yes
→ Go To 2
No
→ Replace the Sun Sensor in accordance with the Service Informa-
tion.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the Sun Sensor/VTSS LED harness connector.
Disconnect the Body Control Module C1 & C2 harness connectors.
Measure the resistance between ground and the Sun Sensor Signal circuit.
Is the resistance below 100.0 ohms?
All
Yes
→ Repair the Sun Sensor Signal circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Turn the ignition off.
Disconnect the Sun Sensor/VTSS LED harness connector.
Disconnect the Body Control Module C1 & C2 harness connectors.
Measure the resistance between the Sun Sensor Signal circuit and the Sensor
Ground circuit in the Sun Sensor harness connector.
Is the resistance below 100.0 ohms?
All
Yes
→ Repair the Sun Sensor Signal circuit for a short to the Sensor
Ground circuit.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
319
HEATING & A/C
TEST
ACTION
APPLICABILITY
4
If there are no possible causes remaining, view repair.
All
Repair
Replace and program the Body Control Module in accordance with
the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
320
HEATING & A/C
SUN LOAD SENSOR FAILURE - ATC —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст