Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 674
QUARTER TRIM PANEL
REMOVAL
(1) Lower convertible top.
(2) Remove rear seat cushion and rear seat back.
(3) Remove door sill trim panel.
(4) Remove speaker grille (Fig. 16).
(5) Remove vertical screws and inboard screw
attaching quarter trim panel to inner quarter panel
(Fig. 17).
(6) Remove screws attaching quarter trim panel to
inner quarter panel through the speaker opening.
(7) Lift metal retainer blade at the front out of clip.
(8) Pull trim panel from inner quarter panel and
disconnect speaker wiring connector.
(9) Remove quarter trim panel from vehicle.
INSTALLATION
(1) Replace push in fasteners.
(2) Position quarter trim panel on vehicle.
(3) Connect speaker wiring connector.
(4) Install screws attaching quarter trim panel to
inner quarter panel through the speaker opening.
(5) Install
vertical
screws
and
inboard
screw
attaching quarter trim panel to inner quarter panel.
(6) Place toe blade into slotted sill clip.
(7) Install door sill trim panel.
(8) Install speaker grille.
(9) Install rear seat cushion and rear seat back.
REAR SHELF TRIM PANEL
REMOVAL
(1) Remove upper quarter trim panels as neces-
sary. (Refer to 23 - BODY/INTERIOR/UPPER QUAR-
TER TRIM - REMOVAL)
(2) Fold seat backs down.
(3) Remove the center plug (Fig. 18).
(4) Remove close out panel trim.
(5) Remove push-in fasteners attaching rear shelf
trim to shelf panel (Fig. 19).
Fig. 18 REAR SHELF CENTER PLUG
1 - CENTER PLUG
2 - REAR SHELF TRIM
Fig. 16 Speaker Grille
1 - QUARTER TRIM PANEL
2 - SPEAKER GRILLE
Fig. 17 Quarter Trim Panel
1 - SCREWS
2 - QUARTER TRIM PANEL
3 - LOCATING PINS
4 - SPEAKER WIRE AND CONNECTOR
5 - INNER QUARTER PANEL
JR
INTERIOR
23 - 93
(6) Disconnect the center shoulder belt at the base.
(Refer
to
8
-
ELECTRICAL/RESTRAINTS/SEAT
BELT & RETRACTOR - REMOVAL)
(7) Pull trim forward to disengage clip attaching
trim to shelf panel.
(8) Feed seat belt through the seat belt opening in
the shelf panel.
CAUTION: Do not pull on child tether covers or use
as a handle for removal of panel.
(9) Remove shelf trim from vehicle.
INSTALLATION
(1) Feed center shoulder belt through opening in
shelf panel.
(2) Place rear shelf trim into position.
(3) Push trim rearward to engage clip attaching
rear shelf trim to shelf panel.
(4) Install push-in fasteners attaching rear shelf
trim to shelf panel.
CAUTION: Do not pull on child tether covers or use
as a handle for installation of panel.
(5) Install close out trim panel.
(6) Install center plug.
(7) Install upper quarter trim panels. (Refer to 23 -
BODY/INTERIOR/UPPER
QUARTER
TRIM
-
INSTALLATION)
(8) Connect the center shoulder seat belt. (Refer to
8
-
ELECTRICAL/RESTRAINTS/SEAT
BELT
&
RETRACTOR - INSTALLATION)
(9) Fold seat backs up.
REAR VIEW MIRROR
REMOVAL
REMOVAL
(1) Remove screws attaching inside rear view mir-
ror to header panel.
(2) Disconnect wire connector to rear view mirror,
if so equipped.
(3) Remove rear view mirror from vehicle (Fig. 20)
REMOVAL - JR-27 ONLY
All vehicles with driver and passenger side airbags
must have a colored coded five Bullet point airbag
warning label applied to the sun visor, verify label
availability and ensure the label is installed.
(1) Disengage sun visor from sun visor support.
(2) Remove screws attaching sun visor to header
panel.
(3) Disconnect lighted vanity mirror wiring.
(4) Remove sun visor from vehicle (Fig. 21).
INSTALLATION
INSTALLATION
(1) Position inside rear view mirror to vehicle.
Fig. 19 REAR SHELF TRIM
1 - PUSH-IN FASTENERS
2 - CENTER SHOULDER BELT
3 - SHELF TRIM PANEL
Fig. 20 Inside Rear View Mirror
1 - MIRROR WIRE CONNECTOR
2 - SET SCREW
3 - REAR VIEW MIRROR
4 - SUPPORT BUTTON
5 - WINDSHIELD
23 - 94
INTERIOR
JR
REAR SHELF TRIM PANEL (Continued)
(2) Connect wire connector to rear view mirror, if
so equipped.
(3) Install screws attaching rear view mirror to
header panel.
INSTALLATION - JR-27 ONLY
All vehicles with driver and passenger side airbags
must have a colored coded five Bullet point airbag
warning label applied to the sun visor, verify label
availability and ensure the label is installed.
(1) Position sun visor to vehicle.
(2) Connect lighted vanity mirror wire connector.
(3) Install screws attaching sun visor to header
panel.
(4) Engage sun visor to sun visor support.
SHIFT BOOT
REMOVAL
(1) Remove the shifter nob set screw and pull knob
off of the shifter (Fig. 22).
NOTE: Do not use a trim stick or tool to remove
transmission range indicator.
(2) Remove transmission range indicator bezel by
squeezing the sides slightly and lifting up until the
locking tabs are free of the floor console. Refer to
(Fig. 22) for pressure points.
(3) Disconnect the electrical connector, if equipped,
and remove the shift boot (Fig. 23).
Fig. 21 Sun Visor
1 - Header Panel
2 - Attaching Screw(s)
3 - Vanity Wire Connectors
4 - Sun Visor
5 - Support Visor Center
Fig. 22 SHIFT KNOB – AUTOMATIC TRANS
1 - SHIFTER KNOB
2 - SET SCREW
3 - SHIFT BOOT
Fig. 23 SHIFT BOOT – TYPICAL
1 - FLOOR CONSOLE
2 - SHIFT BOOT
3 - ELECTRICAL CONNECTOR
JR
INTERIOR
23 - 95
REAR VIEW MIRROR (Continued)
INSTALLATION
(1) Place shift boot into position (Fig. 24).
(2) Connect transmission range indicator bezel
wire connector on the underside of bezel.
(3) Install transmission range indicator bezel by
align alignment pins with holes in console. Apply a
downward pressure until the locking tabs snap into
position.
(4) Install the shifter nob and tighten the set
screw to 3 N·m (23 in. lbs.) (Fig. 25).
SUN VISOR
REMOVAL
(1) Disengage sun visor from center support (Fig.
26).
(2) Remove screws attaching sun visor to roof
header.
(3) Remove sun visor from header.
(4) If equipped, disconnect wire connector from
body harness.
(5) Remove sun visor from vehicle.
INSTALLATION
(1) Place sun visor into position.
(2) If equipped, connect wire connector to body
harness.
(3) Install screw attaching sun visor to header.
(4) Install screws attaching sun visor to roof
header.
(5) Connect sun visor to center support.
SUN VISOR SUPPORT
REMOVAL
(1) Disengage sun visor from center support.
(2) Remove screw attaching support to roof header,
(3) Remove support from vehicle.
INSTALLATION
(1) Place support into position.
(2) Install screw attaching support to roof header,
(3) Engage sun visor to center support.
Fig. 24 SHIFT BOOT – TYPICAL
1 - FLOOR CONSOLE
2 - SHIFT BOOT
3 - ELECTRICAL CONNECTOR
Fig. 25 SHIFT KNOB – AUTOMATIC TRANS
1 - SHIFTER KNOB
2 - SET SCREW
3 - SHIFT BOOT
Fig. 26 Sun Visor
1 - SUN VISOR
2 - HEADLINING
3 - SUPPORT
23 - 96
INTERIOR
JR
SHIFT BOOT (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст