Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 67
Symptom:
*HI BEAM HEADLAMPS WILL NOT TURN OFF
POSSIBLE CAUSES
HEADLAMP DELAY RELAY OUTPUT CIRCUIT SHORT TO VOLTAGE
HEADLAMP DELAY RELAY
HEADLAMP DELAY RELAY CONTROL CIRCUIT SHORT TO VOLTAGE
MULTIFUNCTION SWITCH
TEST
ACTION
APPLICABILITY
1
Remove the Headlamp Delay Relay from the junction block.
Did the High Beam Headlamps turn off?
All
Yes
→ Go To 2
No
→ Repair the Headlamp Delay Relay Output Circuit for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.
2
Remove the Headlamp Delay Relay.
Measure the voltage of the Headlamp Delay Relay Control circuit in the relay
connector.
Is the voltage above 1.0 volts?
All
Yes
→ Go To 3
No
→ Replace the Headlamp Delay Relay.
Perform BODY VERIFICATION TEST - VER 1.
3
Remove the Headlamp Delay Relay from the junction block.
Disconnect the Multifunction Switch connector.
Measure the voltage of the Switched Headlamp Delay Relay Control circuit to
ground.
Is the voltage above 1.0 volts?
All
Yes
→ Repair the Headlamp Delay Relay Control Circuit for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Multifunction Switch.
Perform BODY VERIFICATION TEST - VER 1.
253
EXTERIOR LIGHTING
Symptom:
*HIGH BEAM HEADLAMPS WILL NOT TURN ON
POSSIBLE CAUSES
OPEN FUSED B+
FUSED LOW BEAM OUTPUT CIRCUIT SHORT TO GROUND
FUSED HIGH BEAM OUTPUT CIRCUIT SHORT TO GROUND
HEADLAMP DELAY RELAY
FUSED LOW BEAM OUTPUT CIRCUIT OPEN
HEADLAMP DELAY RELAY CONTROL CIRCUIT OPEN
MULTIFUNCTION SWITCH
TEST
ACTION
APPLICABILITY
1
Turn the Headlamps on.
Gain access to the High Beam Headlamp Relay in the junction block.
Cycle the high beam switch on the multifunction switch and listen to or feel the High
Beam Relay for a click.
Does the relay click?
All
Yes
→ Go To 2
No
→ Go To 3
2
Remove the Headlamp Delay Relay.
Measure the voltage of the Fused B+ circuit at the Headlamp Delay Relay connector.
Is the voltage above 10.0 volts?
All
Yes
→ Go To 3
No
→ Repair the open fused B+ circuit from PDC fuse 4.
Perform BODY VERIFICATION TEST - VER 1.
3
Remove fuse 4 from the PDC.
Disconnect the Multifunction Switch connector.
Measure the resistance of the Fused Low Beam Output Circuit to ground.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Fused Low Beam output circuit for a short to ground
condition.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
4
Remove the Headlamp Delay Relay from the junction block.
Disconnect the Multifunction Switch connector.
Measure the resistance of the Headlamp Delay Relay Control circuit to ground.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Fused High Beam Output Circuit for a short to ground
condition.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
254
EXTERIOR LIGHTING
TEST
ACTION
APPLICABILITY
5
Disconnect the Multifunction Switch connector.
Turn the headlamps on.
Measure the voltage of the Fused Low Beam Relay Output circuit in the multifunc-
tion switch connector.
Is the voltage below 10.0 volts?
All
Yes
→ Replace the Headlamp Delay Relay.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 6
6
Disconnect the Multifunction Switch connector.
Turn the headlamps on.
Measure the voltage of the Fused Low Beam Relay Output circuit in the multifunc-
tion switch connector.
Is the voltage above 5.0 volts?
All
Yes
→ Go To 7
No
→ Repair the open Fused Low Beam Output circuit.
Perform BODY VERIFICATION TEST - VER 1.
7
Disconnect the Multifunction Switch connector.
Turn the headlamps on.
Ensure the Headlamp Delay Relay is installed.
Connect a jumper wire between the Fused Low Beam Relay Output and the Switched
High Beam Relay Control circuits in the multifunction switch connector.
Did the High Beam Headlamps come on?
All
Yes
→ Repair the Headlamp Delay Relay Control Circuit for an open
condition.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Multifunction Switch.
Perform BODY VERIFICATION TEST - VER 1.
255
EXTERIOR LIGHTING
*HIGH BEAM HEADLAMPS WILL NOT TURN ON —
Continued
Symptom:
*LOW BEAM HEADLAMPS WILL NO TURN OFF
POSSIBLE CAUSES
MULTIFUNCTION SWITCH
HEADLAMP DELAY RELAY OUTPUT CIRCUIT SHORT TO VOLTAGE
HEADLAMP DELAY RELAY
JUNCTION BLOCK
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the headlamp switch to the off position.
With the DRBIII
t, read the Headlamp Switch Voltage.
Does the DRBIII
t display Headlamp Switch Voltage between 4.3 and 4.8 Volts?
All
Yes
→ Go To 2
No
→ Replace the Multifunction Switch.
Perform BODY VERIFICATION TEST - VER 1.
2
Remove the Headlamp Delay Relay from the junction block.
Did the Low Beams turn off?
All
Yes
→ Go To 3
No
→ Repair the Headlamp Delay Relay Output Circuit for a short to
voltage condition.
Perform BODY VERIFICATION TEST - VER 1.
3
Substitute a known good relay in place of the Headlamp Delay Relay.
Does the system operate normally?
All
Yes
→ Replace the Headlamp Delay Relay.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
4
Turn the ignition off.
Remove the Headlamp Delay Relay.
Remove the Body Control Module from the junction block.
Measure the resistance of the Headlamp Delay Relay Control Circuit and ground.
Is the resistance below 100.0 ohms?
All
Yes
→ Replace the Junction Block
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Body Control Module.
Perform BODY VERIFICATION TEST - VER 1.
256
EXTERIOR LIGHTING
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст