Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 538
REAR BUMPER
REINFORCEMENT
REMOVAL
(1) Remove rear fascia.
(2) Support bumper reinforcement on a suitable
lifting device.
(3) Mark position of nuts on frame rail to aid in
installation.
(4) Remove nuts attaching rear bumper reinforce-
ment to frame rail (Fig. 4).
(5) Remove bumper reinforcement from vehicle.
INSTALLATION
(1) Position rear bumper reinforcement on vehicle.
(2) Install nuts attaching bumper reinforcement to
frame rail. Use marks made previously to properly
position bumper reinforcement.
(3) Tighten nuts to 28 N·m (250 in. lbs.) torque.
(4) Install rear fascia.
Fig. 2 FRONT FASCIA - JR-27
1 - PUSH PIN(S) TO UPPER RADIATOR CROSSMEMBER
2 - SCREW/WASHER FRONT FASCIA TO FRONT FENDER
3 - SCREW/WASHER FRONT FASCIA TO SPLASH SHIELD
4 - PUSH PIN(S) FRONT FASCIA TO LOWER CROSSMEMBER
5 - FRONT FASCIA
Fig. 3 Front Bumper Energy Management Foam
1 - FRONT BUMPER ENERGY MANAGEMENT FOAM
2 - FRONT FASCIA
Fig. 4 Rear Bumper Reinforcement
1 - FRAME RAIL
2 - FRONT BUMPER REINFORCEMENT
JR
FRAME & BUMPERS
13 - 3
FRONT FASCIA (Continued)
REAR FASCIA
REMOVAL
REMOVAL - JR-41
(1) Release decklid latch and open decklid.
(2) Remove left rear tail lamp and disengage
license plate wire connector from tail lamp. (Refer to
8 - ELECTRICAL/LAMPS/LIGHTING - EXTERIOR/
TAIL LAMP - REMOVAL).
(3) Peel back trunk carpeting at tail lamps and
remove nut and washer from fascia to quarter panel
bracket. Discard nut and washer.
(4) Remove push-in fasteners attaching decklid
slam bumpers to top of fascia.
(5) Remove push-in fastener attaching center of
fascia to rear closure panel.
(6) Remove screws attaching fascia to rear wheel-
house splash shields (Fig. 5).
(7) Remove screws attaching fascia to quarter
panel at the wheelhouse opening.
(8) Slide fascia rearward to disengage hooks hold-
ing fascia to bottom of quarter panel.
(9) Remove fascia from vehicle.
REMOVAL - JR-27
(1) Release decklid latch and open decklid.
(2) Remove tail lamps.
(3) Remove push-in fasteners attaching decklid
slam bumpers to top of fascia.
(4) Remove push-in fastener attaching center of
fascia to rear closure panel.
(5) Remove screws attaching fascia to rear wheel-
house splash shields (Fig. 6).
(6) Remove screws attaching fascia to quarter
panel at the wheelhouse opening.
(7) Slide fascia rearward to disengage hooks hold-
ing fascia to bottom of quarter panel.
(8) Remove fascia from vehicle.
INSTALLATION
INSTALLATION - JR-41
(1) Ensure that the energy management foam is
properly installed in rear fascia.
(2) Position fascia on vehicle.
(3) Slide fascia forward to engage hooks attaching
fascia to bottom of quarter panel.
(4) Install push-in fastener attaching center of fas-
cia to rear closure panel.
(5) Install
push-in
fasteners
attaching
decklid
slam bumpers to top of fascia.
(6) Install new nut and washer to fascia to quarter
panel bracket located in the trunk area.
(7) Install screws attaching fascia to quarter panel
at wheelhouse opening.
(8) Install fasteners attaching fascia to rear wheel-
house splash shields.
(9) Engage license plate wire connector to left tail
lamp.
(10) Install tail lamps. (Refer to 8 - ELECTRICAL/
LAMPS/LIGHTING
-
EXTERIOR/TAIL
LAMP
-
INSTALLATION).
Fig. 5 REAR FASCIA
1 - NUT (FASCIA TO QUARTER PANEL)
2 - SCREW AND WASHER (FASCIA TO QUARTER PANEL)
3 - SCREW (FASCIA TO SPLASHSHIELD)
4 - REAR FASCIA
5 - PUSH PIN (FASCIA TO DECKLID OPENING REINFORCMENT)
6 - LICENSE PLATE LAMP HARNESS
7 - BUMPER REINFORCEMENT
Fig. 6 REAR FASCIA
1 - REAR BUMPER REINFORCEMENT
2 - TRUNK
3 - QUARTER PANEL
4 - REAR FASCIA
13 - 4
FRAME & BUMPERS
JR
INSTALLATION - JR-27
(1) Ensure that the energy management foam is
properly installed in rear fascia (Fig. 7).
(2) Slide fascia forward to engage hooks attaching
fascia to bottom of quarter panel.
(3) Install push-in fastener attaching center of fas-
cia to rear closure panel.
(4) Install
push-in
fasteners
attaching
decklid
slam bumpers to top of fascia.
(5) Install screws attaching fascia to quarter panel
at wheelhouse opening.
(6) Install fasteners attaching fascia to rear wheel-
house splash shields.
(7) Engage license plate wire connector to left tail
lamp.
(8) Install tail lamps. (Refer to 8 - ELECTRICAL/
LAMPS/LIGHTING
-
EXTERIOR/TAIL
LAMP
-
INSTALLATION).
FRAME
SPECIFICATIONS - FRAME DIMENSIONS
Frame dimensions are listed in metric scale. All
dimensions are from center to center of Principal
Locating Point (PLP), or from center to center of PLP
and fastener location.
VEHICLE PREPARATION
Position the vehicle on a level work surface. Using
screw or bottle jacks, adjust the vehicle PLP heights
to the specified dimension above a level work surface.
Vertical dimensions can be taken from the work sur-
face to the locations indicated were applicable.
Fig. 7 REAR BUMPER ENERGY MANAGEMENT
FOAM
1 - ENERGY MANAGEMENT FOAM
2 - REAR BUMPER FASCIA
JR
FRAME & BUMPERS
13 - 5
REAR FASCIA (Continued)
INDEX
DESCRIPTION
FIGURE
ENGINE COMPARTMENT TOP VIEW
8
ENGINE COMPARTMENT SIDE VIEW
9
FORWARD FRAME SECTION BOTTOM VIEW
10
REAR FRAME SECTION SIDE VIEW
11
REAR FRAME SECTION BOTTOM VIEW
12
Fig. 8 ENGINE COMPARTMENT TOP VIEW
13 - 6
FRAME & BUMPERS
JR
FRAME (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст