Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 753
REMOVAL
(1) Disconnect negative battery cable.
(2) Remove air inlet tube for the air cleaner box.
(3) Disconnect quick connect hose from the top of
the air pump.
(4) Raise vehicle and support.
(5) Remove 3 mounting nuts (Fig. 2).
(6) Unlock electrical connector (Fig. 3).
(7) Unclip
electrical
connector
from
mounting
bracket (Fig. 4).
(8) Press tab and disconnect electrical connector
(Fig. 5).
Fig. 2 AIR PUMP MOUNTING
Fig. 3 ELECTRICAL CONNECTOR LOCKING TAB
Fig. 4 CONNECTOR RETAINING CLIP
Fig. 5 DEPRESS TAB ON CONNECTOR
JR
AIR INJECTION
25 - 29
PUMP (Continued)
(9) Disconnect quick connect hose from inlet of the
air pump.
(10) Remove air pump from vehicle (Fig. 6).
INSTALLATION
(1) Install air pump to vehicle (Fig. 6).
(2) Connect quick connect hose to inlet of air
pump.
(3) Connect electrical connector (Fig. 5).
(4) Clip electrical connector to mounting bracket
(Fig. 4).
(5) Install 3 mounting nuts (Fig. 2) and tighten.
(6) Lower vehicle.
(7) Connect quick connect hose to the top of air
pump.
(8) Install air inlet tube for the air cleaner box.
(9) Connect negative battery cable.
AIR PUMP FILTER
DESCRIPTION
The filter is part of the Mass Air Flow Sensor
(MAF).
ONE WAY CHECK VALVE
DESCRIPTION
The check valve is located on the exhaust manifold.
OPERATION
The one-way check valve has a one-way diaphragm
which prevents hot exhaust gases from backing up
into the air injection hose and air injection pump.
The check valve will protect the system if the air
injection pump, an air hose ruptures or exhaust sys-
tem pressure becomes abnormally high.
REMOVAL
Location of One Way Check Valve and connector
hose (Fig. 7).
(1) Squeeze quick connector (Fig. 8) on the con-
necting tube and pull from check valve.
(2) Remove the 2 check valve retaining screws.
(3) Remove check valve from exhaust manifold.
INSTALLATION
(1) Clean the check valve sealing surface on the
exhaust manifold.
Fig. 6 AIR PUMP REMOVED
Fig. 7 VALVE AND CONNECTOR HOSE
Fig. 8 QUICK CONNECTOR OPERATION
25 - 30
AIR INJECTION
JR
PUMP (Continued)
(2) Install One Way Check Valve with NEW gas-
ket.
(3) Torque 2 retaining screws to 12 Nm (105 in
lbs).
(4) Push connecting tube into check valve.
CONNECTING TUBE
REMOVAL
(1) Remove air inlet duct to air cleaner box (Fig.
9).
(2) Squeeze the quick connect on the tube to
release it (Fig. 10).
(3) Disconnect connector tube at air pump (Fig. 11)
and one way check valve (Fig. 12).
(4) Remove connector tube, note routing of tube.
Fig. 9 AIR CLEANER INLET TUBE
Fig. 10 CONNECTOR TUBE QUICK CONNECT
Fig. 11 AIR PUMP TUBE CONNECTION
Fig. 12 VALVE AND CONNECTOR HOSE
JR
AIR INJECTION
25 - 31
ONE WAY CHECK VALVE (Continued)
INSTALLATION
(1) Route tube.
(2) Connect to one way check valve (Fig. 12) and
tube to air pump (Fig. 11).
(3) Install air inlet duct to air cleaner box (Fig. 9).
CONNECTOR TUBE ROUTING
CONNECTOR TUBE ROUTING
CONNECTOR TUBE ROUTING
CONNECTOR TUBE ROUTING
25 - 32
AIR INJECTION
JR
CONNECTING TUBE (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст