Chrysler Sebring, Stratus sedan, Sebring Convertible. Manual — part 253
INTRODUCTION
TABLE OF CONTENTS
page
page
BODY CODE PLATE
. . . . . . . . . . . . . . . . . . . . . . . . . . 1
FASTENER IDENTIFICATION
. . . . . . . . . . . . . . . . . . . . . . . . . . 2
FASTENER USAGE
. . . . . . . . . . . . . . . . . . . . . 5
. . . . . . . . . . . . . . . 5
INTERNATIONAL SYMBOLS
. . . . . . . . . . . . . . . . . . . . . . . . . . 5
METRIC SYSTEM
. . . . . . . . . . . . . . . . . . . . . . . . . . 5
TORQUE REFERENCES
. . . . . . . . . . . . . . . . . . . . . . . . . . 8
VEHICLE IDENTIFICATION NUMBER
. . . . . . . . . . . . . . . . . . . . . . . . . . 9
VEHICLE CERTIFICATION LABEL
. . . . . . . . . . . . . . . . . . . . . . . . . 10
E-MARK LABEL
. . . . . . . . . . . . . . . . . . . . . . . . . 10
VECI LABEL
. . . . . . . . . . . . . . . . . . . . . . . . . 11
MANUFACTURER PLATE
. . . . . . . . . . . . . . . . . . . . . . . . . 11
BODY CODE PLATE
DESCRIPTION
The Body Code Plate (Fig. 1) is located in the
engine compartment on the driver side strut tower.
There are seven lines of information on the body code
plate. Lines 4, 5, 6, and 7 are not used to define ser-
vice information. Information reads from left to right,
starting with line 3 in the center of the plate to line
1 at the bottom of the plate.
BODY CODE PLATE LINE 2
DIGITS 1, 2, AND 3
Paint procedure
DIGIT 4
Open Space
DIGITS 5 THROUGH 7
Primary paint
(Refer to 23 - BODY/PAINT - SPECIFICATIONS)
for Body Color Codes.
DIGIT 8 AND 9
Open Space
DIGITS 10 THROUGH 12
Secondary Paint
DIGIT 13 AND 14
Open Space
DIGITS 15 THROUGH 18
Interior Trim Code
DIGIT 19
Open Space
DIGITS 20, 21, AND 22
Engine Code
• ECC = 2.0L Four Cylinder 16 Valves DOHC
(SMPI) Gasoline
Fig. 1 BODY CODE PLATE
1 - PRIMARY PAINT
2 - SECONDARY PAINT
3 - VINYL ROOF
4 - VEHICLE ORDER NUMBER
5 - CAR LINE SHELL
6 - PAINT PROCEDURE
7 - ENGINE
8 - TRIM
9 - TRANSMISSION
10 - MARKET
11 - VIN
JR
INTRODUCTION
1
• EDV = 2.4L Four Cylinder 16 Valves DOHC
High Output Turbo Gasoline
• EDZ = 2.4L Four Cylinder 16 Valves DOHC Gas-
oline
• ED2 = 2.4L Four Cylinder 16 Valves DOHC
PZEV Gasoline
• EEE = 2.7L Six Cylinder 24 Valves FFV
• EER = 2.7L Six Cylinder 24 Valves DOHC (MPI)
Gasoline
DIGIT 23
Open Space
BODY CODE PLATE LINE 1
DIGITS 1, 2, AND 3
Transaxle Codes
• DGL = 4-Speed Automatic Transaxle
• DD5 = 5-Speed Manual Transaxle
DIGIT 4
Open Space
DIGIT 5
Market Code
• C = Canada
• B = International
• M = Mexico
• U = United States
DIGIT 6
Open Space
DIGITS 7 THROUGH 23
Vehicle Identification Number
• Refer to Vehicle Identification Number (VIN)
paragraph for proper breakdown of VIN code.
IF TWO BODY CODE PLATES ARE REQUIRED
The last code shown on either plate will be fol-
lowed by END. When two plates are required, the
last code space on the first plate will indicate (CTD)
When a second plate is required, the first four
spaces of each line will not be used due to overlap of
the plates.
FASTENER IDENTIFICATION
DESCRIPTION
The SAE bolt strength grades range from grade 2
to grade 8. The higher the grade number, the greater
the bolt strength. Identification is determined by the
line marks on the top of each bolt head. The actual
bolt strength grade corresponds to the number of line
marks plus 2. The most commonly used metric bolt
strength classes are 9.8 and 10.9. The metric
strength class identification number is imprinted on
the head of the bolt. The higher the class number,
the greater the bolt strength. Some metric nuts are
imprinted with a single-digit strength class on the
nut face. Refer to the Fastener Identification and
Fastener Strength Charts.
BOLT MARKINGS AND TORQUES - METRIC
Bolt Markings
8.8/8.9
10.9
12.9
Bolt Dia.
N·m
Ft. Lbs.
N·m
Ft. Lbs.
N·m
Ft. Lbs.
6
12
105*
14
120*
16
12
8
25
250*
32
23
38
28
10
54
40
60
45
74
55
12
95
70
108
80
135
100
14
155
115
175
130
216
160
16
243
180
324
210
324
240
* Inch Lbs.
2
INTRODUCTION
JR
BODY CODE PLATE (Continued)
BOLT MARKINGS AND TORQUES - U. S. CUSTOMARY
Bolt Markings
Grade 5
Grade 8
Bolt Dia.
N·m
Ft. Lbs
N·m
Ft. Lbs
1/4 - 20
10
95*
14
125*
1/4 - 28
10
95*
17
150*
5/16 - 18
22
200*
30
270*
5/16 - 24
26
240*
33
300*
3/8 - 16
40
30
55
40
3/8 - 24
47
35
60
45
7/16 - 14
68
50
88
65
7/16 - 20
74
55
95
70
1/2 - 13
101
75
135
100
1/2 -20
115
85
150
110
9/16 - 12
135
105
182
135
9/16 - 18
155
115
202
150
5/8 - 11
202
150
263
195
5/8 - 18
215
160
284
210
3/4 - 10
230
170
297
220
3/4 - 16
236
175
304
225
7/8 - 14
405
300
540
400
* Inch Lbs.
JR
INTRODUCTION
3
FASTENER IDENTIFICATION (Continued)
Fig. 2 FASTENER STRENGTH
4
INTRODUCTION
JR
FASTENER IDENTIFICATION (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст