Chrysler RG Voyager. Manual — part 1151
SEAT CUSHION COVER/FOAM -
THIRD ROW - FOLD-IN-FLOOR
REMOVAL
(1) Third row seat in the upright position.
(2) Remove the third row cushion side shield (Fig.
130).
(3) Fold the third row seat into floor well.
(4) Remove seat cushion pan carpet to floor panel
using a trim tool (Fig. 131).
(5) Using a trim tool, remove seat cushion pan bot-
tom side panel (Fig. 132).
(6) Remove handle from cushion.
(7) Place seat with the seat back down position.
(8) Disengage seat cushion cover J-straps from
cushion pan (Fig. 133).
(9) Remove cover and foam from cushion pan.
(10) Separate the cover and foam.
INSTALLATION
(1) Place the seat cushion cover and foam together.
(2) Install seat cushion cover and foam onto cush-
ion pan.
(3) Engage seat cushion cover J-straps to cushion
pan (Fig. 133).
(4) Install handle on cushion.
Fig. 130 THIRD ROW SEAT BACK COVER
1 - ATTACHING SCREW
Fig. 131 SEAT CUSHION CARPETING
1 - CARPET FROM SEAT TO FLOOR
2 - SEAT CUSHION PAN COVER
Fig. 132 THIRD ROW CUSHION PAN COVER
Fig. 133 THIRD ROW CUSHION PAN
RS
SEATS
23 - 183
(5) Fold seat into floor well.
(6) Install seat cushion pan bottom side panel (Fig.
132).
(7) Install seat cushion pan carpet to floor panel
(Fig. 131).
(8) Install the third row cushion side shield (Fig.
130).
(9) Place third row seat in the upright position.
SIDE SHIELD CUP HOLDER -
FOLD-IN-FLOOR
REMOVAL
(1) Open cup holder door.
(2) Remove two screws attaching cup holder to
side shield (Fig. 134).
INSTALLATION
(1) Place cup holder into position (Fig. 134).
(2) Install the two cup holder attaching screws.
SEAT RECLINER/FOLD
FORWARD MECHANISM
-THIRD ROW -FOLD-IN-FLOOR
REMOVAL
(1) Remove seat back frame. (Refer to 23 - BODY/
SEATS/SEAT BACK FRAME - REMOVAL).
(2) Remove the side shields from seat cushion.
(3) Remove two recliner/fold forward mechanism
bolts on each side from cushion pan.
(4) Remove the recliner/fold forward mechanism
from seat cushion pan.
INSTALLATION
(1) Place recliner/fold forward mechanism on seat
cushion pan.
(2) Install two recliner/fold forward mechanism
bolts on each side to cushion pan.
(3) Install the side shields to seat cushion.
(4) Install seat back frame. (Refer to 23 - BODY/
SEATS/SEAT BACK FRAME - INSTALLATION).
THIRD ROW FOLD-IN-FLOOR
SEAT LEG RETRACTING
CABLE
REMOVAL
(1) Remove the seat from vehicle. (Refer to 23 -
BODY/SEATS/SEAT - REMOVAL).
(2) Place seat assembly upside down in the folded
seat position on a clean bench surface.
(3) Remove inboard leg trim screw.
(4) Rotate the front inboard leg down in the stow
position by hand
(5) Using a flat bladed tool, remove the leg cover
from the seat leg (Fig. 135).
(6) Remove cable end clip by prying up on the base
of the clip (Fig. 136) and (Fig. 137).
(7) Remove steel pulley by prying the pulley
toward the front of the seat (Fig. 138).
Fig. 134 SECOND ROW SEAT CUP HOLDER
1 - ATTACHING SCREWS
Fig. 135 REMOVING FRONT LEG COVER
1 - SCREWDRIVER (OR EQUIVALENT)
2 - FRONT LEG COVER
23 - 184
SEATS
RS
SEAT CUSHION COVER/FOAM - THIRD ROW - FOLD-IN-FLOOR (Continued)
(8) Remove eyelet clip from the spring at the back
of the seat, located in the rear leg (Fig. 139).
(9) Remove spring from the rear foot.
(10) Remove cable from retainer at the base of the
rear foot (Fig. 140).
(11) Remove tie strap securing cable housing (Fig.
141).
(12) Remove cable from seat.
Fig. 136 REMOVING CABLE END CLIP
1 - FRONT LEG
2 - CABLE END CLIP
3 - SCREWDRIVER (OR EQUIVALENT)
Fig. 137 CABLE PULLEY
1 - PULLEY
2 - CABLE RETAINER
Fig. 138 REMOVING PULLEY
1 - FRONT OF SEAT ASSEMBLY
2 - FRONT LEG
3 - FLAT BLADED TOOL (OR EQUIVALENT)
4 - HAMMER
Fig. 139 TENSION SPRING
RS
SEATS
23 - 185
THIRD ROW FOLD-IN-FLOOR SEAT LEG RETRACTING CABLE (Continued)
INSTALLATION
(1) Slide the new cable through the retaining
bracket. Ensure that the eyelet hook is towards the
rear of seat.
(2) Continue feeding cable through the retaining
bracket until the conduit is through.
(3) Feed eyelet through the rear foot. The cable
must run underneath the pivot shaft at the base, and
feed up through the rear foot. Leave slack in the
cable (Fig. 142).
Fig. 140 REMOVING CABLE FROM THE RETAINER
1 - CABLE HOUSING
2 - SCREWDRIVER (OR EQUIVALENT)
3 - REAR LEG OF THE SEAT
Fig. 141 TIE STRAP LOCATION
1 - TIE STRAP LOCATION
2 - SEAT COVERING
Fig. 142 FEED EYELET HOOK THROUGH REAR
FOOT
1 - REAR LEG OF SEAT
2 - CABLE EYELET
3 - REAR LEG PIVOT SHAFT
23 - 186
SEATS
RS
THIRD ROW FOLD-IN-FLOOR SEAT LEG RETRACTING CABLE (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст