Chrysler RG Voyager. Manual — part 196
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Gain access to the bottom of the Fuse and Relay Center.
Disconnect connector C9 from the Fuse and Relay Center.
Measure the resistance of the Fused Ignition Switch Output circuit between the FCM
connector cavity 37 and the Fuse and Relay Center connector C9 cavity 2.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Fused Ignition Switch Output (Start) circuit for an
open between the Fuse and Relay Center and the ignition switch.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Fuse and Relay Center.
Perform BODY VERIFICATION TEST - VER 1.
753
IGNITION, POWER, ACCESSORY
IGNITION START INPUT WIRING —
Continued
Symptom:
INTERNAL DRIVER FAULT #1
When Monitored and Set Condition:
INTERNAL DRIVER FAULT #1
When Monitored:
Continuously with the ignition on.
Set Condition:
The FCM has detected an internal malfunction of the module.
POSSIBLE CAUSES
FRONT CONTROL MODULE INTERNAL MALFUNCTION
INTERMITTENT CONDITION
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, erase the current Front Control Module DTC’s.
Turn the ignition off, wait 10 seconds then turn the ignition on.
With the DRBIII
t, read the current Front Control Module DTC’s.
Does the DRBIII
t display: INTERNAL DRIVER FAULT #1?
All
Yes
→ Replace the Front Control Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ This symptom represents an internal malfunction in the Front
Control Module. The condition that caused this symptom is
currently not present.
Perform BODY VERIFICATION TEST - VER 1.
754
IGNITION, POWER, ACCESSORY
Symptom:
INTERNAL DRIVER FAULT #2
When Monitored and Set Condition:
INTERNAL DRIVER FAULT #2
When Monitored:
Continuously with the ignition on.
Set Condition:
The FCM has detected an internal malfunction of the module.
POSSIBLE CAUSES
FRONT CONTROL MODULE INTERNAL MALFUNCTION
INTERMITTENT CONDITION
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, erase the current Front Control Module DTC’s.
Turn the ignition off, wait 10 seconds then turn the ignition on.
With the DRBIII
t, read the current Front Control Module DTC’s.
Does the DRBIII
t display: INTERNAL DRIVER FAULT #2?
All
Yes
→ Replace the Front Control Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ This symptom represents an internal malfunction in the Front
Control Module. The condition that caused this symptom is
currently not present.
Perform BODY VERIFICATION TEST - VER 1.
755
IGNITION, POWER, ACCESSORY
Symptom:
INTERNAL DRIVER FAULT #3
When Monitored and Set Condition:
INTERNAL DRIVER FAULT #3
When Monitored:
Continuously with the ignition on.
Set Condition:
The FCM has detected an internal malfunction of the module.
POSSIBLE CAUSES
FRONT CONTROL MODULE INTERNAL MALFUNCTION
INTERMITTENT CONDITION
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, erase the current Front Control Module DTC’s.
Turn the ignition off, wait 10 seconds then turn the ignition on.
With the DRBIII
t, read the current Front Control Module DTC’s.
Does the DRBIII
t display: INTERNAL DRIVER FAULT #3?
All
Yes
→ Replace the Front Control Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ This symptom represents an internal malfunction in the Front
Control Module. The condition that caused this symptom is
currently not present.
Perform BODY VERIFICATION TEST - VER 1.
756
IGNITION, POWER, ACCESSORY
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст