Chrysler RG Voyager. Manual — part 123
Symptom:
FCM, BCM COMMUNICATION FAULT
When Monitored and Set Condition:
FCM, BCM COMMUNICATION FAULT
When Monitored:
With the ignition in run, and the IOD fuse installed.
Set Condition:
The FCM does not receive any messages from the Body Control Module
(BCM) for at least 5 seconds.
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE BCM
FRONT CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, attempt to communicate with the BCM.
Was the DRB able to I/D or communicate with the BCM?
All
Yes
→ Go To 2
No
→ Refer to the Communication category for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
2
With the DRB, erase DTC’s.
Cycle the ignition switch from off to on and wait approximately 1 minute.
With the DRB, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Front Control Module in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
461
COMMUNICATION
Symptom:
FCM, HVAC COMMUNICATION FAULT
When Monitored and Set Condition:
FCM, HVAC COMMUNICATION FAULT
When Monitored:
With the ignition in run, and the IOD fuse installed.
Set Condition:
The FCM does not receive any messages from the Automatic Temperature
Control (ATC) module or the A/C Heater Control (MTC) for at least 20 seconds.
POSSIBLE CAUSES
ATTEMPT TO COMMUNICATE WITH THE HVAC
FRONT CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, attempt to communicate with the A/C Heater Control (MTC) or the
Automatic Temp Control (ATC).
Was the DRB able to I/D or communicate with the HVAC or the ATC?
All
Yes
→ Go To 2
No
→ Refer to the Communication category for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
2
With the DRB, erase DTC’s.
Cycle the ignition switch from off to on and wait approximately 1 minute.
With the DRB, read DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Front Control Module in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
462
COMMUNICATION
Symptom:
FCM, PCI INTERNAL FAULT
When Monitored and Set Condition:
FCM, PCI INTERNAL FAULT
When Monitored:
Continuously.
Set Condition:
The DTC will set if the FCM detects an internal fault.
POSSIBLE CAUSES
FCM, PCI INTERNAL FAULT
TEST
ACTION
APPLICABILITY
1
Connect the DRB to the Data Link Connector.
Turn the ignition on.
With the DRB, erase FCM DTC’s.
Turn the ignition off then turn the ignition on.
With the DRB, read FCM DTC’s.
Did this DTC reset?
All
Yes
→ Replace the Front Control Module in accordance with the service
information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
463
COMMUNICATION
Symptom:
FCM, PCM COMMUNICATION FAULT
When Monitored and Set Condition:
FCM, PCM COMMUNICATION FAULT
When Monitored:
With the ignition in run, and the IOD fuse installed.
Set Condition:
The FCM does not receive any messages from the PCM for at least 5
seconds.
POSSIBLE CAUSES
PCM COMMUNICATION FAULT
ATTEMPT TO COMMUNICATE WITH THE PCM
PCI BUS CIRCUIT OPEN
POWERTRAIN CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRB, enter Instrument Cluster, System Tests then PCM Monitor.
Does the DRB display: PCM is active on BUS?
All
Yes
→ Erase the DTC, if DTC resets, replace the Front Control Module
in accordance with the service information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition on.
With the DRB, attempt to communicate with the PCM.
Was the DRB able to communicate with the PCM?
All
Yes
→ Go To 3
No
→ Refer to the communication category and perform the appropriate
symptom.
Perform BODY VERIFICATION TEST - VER 1.
464
COMMUNICATION
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст