Chrysler RG Voyager. Manual — part 1154
![](/vehicles/ged/giekucalind/wad/vebond.png)
FRONT DOOR OUTER BELT
MOLDING
REMOVAL
(1) Remove the side view mirror. (Refer to 23 -
BODY/EXTERIOR/SIDE
VIEW
MIRROR
-
REMOVAL)
(2) Remove door trim panel.
(3) Roll door glass down.
(4) Using a hook tool, disengage interlocking lip at
the base of the inward edge of the belt molding (Fig.
1).
(5) Remove belt molding from door.
INSTALLATION
(1) Place belt molding in position on door (Fig. 1).
NOTE: Make sure end of applique is against outer
belt.
(2) Engage interlocking lip at the base of the
inward edge of the belt molding on door panel.
(3) Install door trim panel.
FRONT DOOR WEATHERSTRIP
REMOVAL
(1) Open front door.
(2) Using fork tool (C-4829), remove push pin fas-
teners attaching front door weatherstrip to end
frames and bottom of door (Fig. 2).
(3) Pull
weatherstrip
from
retaining
channel
around window frame.
(4) Remove weatherstrip from vehicle.
INSTALLATION
(1) Position weatherstrip on door.
(2) Install push pin fasteners attaching front door
weatherstrip to end frames and bottom of door (Fig.
2).
(3) Install weatherstrip into retaining channel
around window frame.
(4) Close front door.
Fig. 1 FRONT DOOR WEATHERSTRIP
1 - DOOR GLASS RUN WEATHERSTRIP
2 - FRONT INNER DOOR
3 - DOOR BELT OUTER WEATHERSTRIP
4 - DOOR MOUNTED WEATHERSTRIP
5 - DOOR OUTER BELT WEATHERSTRIP
RS
WEATHERSTRIP/SEALS
23 - 195
FRONT DOOR GLASS RUN WEATHERSTRIP (Continued)
![](/vehicles/ged/giekucalind/wad/rigera.png)
SLIDING DOOR
WEATHERSTRIP
REMOVAL
(1) Open sliding door.
(2) Remove door opening sill plate.
(3) Loosen B-pillar trim covers.
(4) Loosen quarter panel trim panels.
(5) From splice at the bottom center of door open-
ing, pull weatherstrip from pinch flange around door
opening.
INSTALLATION
(1) Place splice at the bottom center of door open-
ing, pushing weatherstrip onto pinch flange around
door opening.
(2) Tighten quarter panel trim panels.
(3) Tighten B-pillar trim covers.
(4) Install door opening sill plate.
(5) Close sliding and check alignment.
FRONT DOOR INNER BELT
MOLDING
REMOVAL
(1) Remove door trim panel.
(2) Peel upper corner seals away form inner belt
molding to clear removal path.
(3) Pull inner belt molding upward to disengage
retaining channel in bottom of molding from door
panel flange (Fig. 1).
(4) Remove inner belt molding from vehicle.
INSTALLATION
(1) Place inner belt molding in position on door
(Fig. 1).
(2) Push inner belt molding downward to engage
retaining channel onto door panel flange.
(3) Install upper corner seals in proper location.
(4) Install door trim panel.
Fig. 2 Front Door Weatherstrip
1 - RETAINING CHANNEL
2 - PUSH-IN FASTENER
3 - WEATHERSTRIP
4 - FRONT DOOR
23 - 196
WEATHERSTRIP/SEALS
RS
FRONT DOOR WEATHERSTRIP (Continued)
BODY STRUCTURE
TABLE OF CONTENTS
page
page
GAP AND FLUSH
SPECIFICATIONS - GAP AND FLUSH
. . . . . . . . . . . . . . . . . . . . 197
OPENING DIMENSIONS
. . . . . . . . . . . . . . . . . . . . . . . . 200
SEALER LOCATIONS
LOCATIONS . . . . . . . . . . . . . . . . . . . . . . . . . 203
LOCATIONS - FOLD-IN-FLOOR ONLY . . . . . 231
STRUCTURAL ADHESIVE LOCATIONS
ADHESIVE LOCATIONS . . . . . . . . . . . . . . . . 240
WELD LOCATIONS
SPECIFICATIONS - WELD LOCATIONS
SPECIFICATIONS - WELD LOCATIONS -
FOLD-IN-FLOOR . . . . . . . . . . . . . . . . . . . . . 383
SUNROOF
. . . . . . . . . . . . . . . . . . . . . . . . 407
DRAIN TUBE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 410
. . . . . . . . . . . . . . . . . . . . . . . . 410
GLASS PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
. . . . . . . . . . . . . . . . . . . . . . . . 411
SUNROOF GLASS PANEL ADJUSTMENT
SUNROOF ASSEMBLY
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
. . . . . . . . . . . . . . . . . . . . . . . . 411
SUNSHADE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 411
. . . . . . . . . . . . . . . . . . . . . . . . 411
WIND DEFLECTOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
. . . . . . . . . . . . . . . . . . . . . . . . 412
WATER CHANNEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
. . . . . . . . . . . . . . . . . . . . . . . . 412
SUNROOF MOTOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 412
. . . . . . . . . . . . . . . . . . . . . . . . 412
. . . . . . . . . . . . . . . . . . . . . . . 413
SUNROOF SWITCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . 414
. . . . . . . . . . . . . . . . . . . . . . . . 414
GAP AND FLUSH
SPECIFICATIONS - GAP AND FLUSH
MEASUREMENTS
INDEX
DESCRIPTION
FIGURE
GAP & FLUSH MEASUREMENTS
1
RS
BODY STRUCTURE
23 - 197
![](/vehicles/ged/giekucalind/wad/oth.png)
Fig. 1 GAP & FLUSH MEASUREMENTS
23 - 198
BODY STRUCTURE
RS
GAP AND FLUSH (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст