Chrysler RG Voyager. Manual — part 515
(10) Install crossover cable to gearshift mechanism
(Fig. 158). Install retainer clip (Fig. 159).
(11) Adjust crossover cable (Refer to 21 - TRANS-
MISSION/TRANSAXLE/MANUAL/GEAR
SHIFT
CABLE - ADJUSTMENTS).
(12) Install center console support bracket (Fig.
160). Torque support bracket-to-gearshift mechanism
screws to 12 N·m (108 in. lbs.).
(13) Install center console assembly (Fig. 161).
Install and torque center console-to-gearshift mecha-
nism screws to 5 N·m (45 in. lbs.).
Fig. 158 Crossover Cable at Gearshift Mechanism
1 - GEARSHIFT MECHANISM
2 - CROSSOVER CABLE
Fig. 159 Crossover Cable Retainer Clip
1 - RETAINER CLIP
2 - CROSSOVER CABLE
Fig. 160 Center Console Support Bracket
1 - BRACKET
2 - SCREW
3 - GEARSHIFT MECHANISM
Fig. 161 Center Console Removal/Installation (LHD
Shown — RHD Typical)
1 - CENTER CONSOLE
2 - SCREW (4)
3 - GEARSHIFT MECHANISM
21a - 82
T850 MANUAL TRANSAXLE
RG
GEARSHIFT CABLE - CROSSOVER (Continued)
(14) Install cupholder plugs (Fig. 162).
(15) Install gearshift boot to console (Fig. 163).
Secure with three (3) retainer clips.
(16) Install gearshift knob to gearshift lever (Fig.
164). Orient shift pattern
1
⁄
4
-turn clockwise, push
down
and
rotate
1
⁄
4
-turn
counter-clockwise
and
release. Secure boot to knob.
(17) Connect battery negative cable.
ADJUSTMENTS
ADJUSTMENT
(1) Disconnect battery negative cable.
(2) Remove gearshift knob by pushing down and
rotating
1
⁄
4
-turn clock-wise (Fig. 165).
Fig. 162 Cup Holder Plugs
1 - CUPHOLDER PLUG (2)
Fig. 163 Gearshift Boot Removal/Installation
1 - GEARSHIFT BOOT
2 - CENTER CONSOLE
Fig. 164 Gearshift Knob Removal/Installation
1 - GEARSHIFT KNOB
2 - GEARSHIFT LEVER
Fig. 165 Gearshift Knob Removal/Installation
1 - GEARSHIFT KNOB
2 - GEARSHIFT LEVER
RG
T850 MANUAL TRANSAXLE
21a - 83
GEARSHIFT CABLE - CROSSOVER (Continued)
(3) Remove gearshift boot from center console by
disengaging at three (3) retaining clips (Fig. 166).
(4) Apply park brake to allow park brake handle to
clear center console upon removal.
(5) Remove two (2) cupholder bottom plugs (Fig.
167).
(6) Remove four (4) center console-to-gearshift
mechanism screws. Remove console assembly (Fig.
168).
(7) Loosen crossover cable adjustment screw (Fig.
169).
Fig. 166 Gearshift Boot Removal/Installation
1 - GEARSHIFT BOOT
2 - CENTER CONSOLE
Fig. 167 Cup Holder Plugs
1 - CUPHOLDER PLUG (2)
Fig. 168 Center Console Removal/Installation (LHD
Shown — RHD Typical)
1 - CENTER CONSOLE
2 - SCREW (4)
3 - GEARSHIFT MECHANISM
Fig. 169 Crossover Cable Adjustment Screw
1 - CROSSOVER CABLE
2 - ADJUSTMENT SCREW
21a - 84
T850 MANUAL TRANSAXLE
RG
GEARSHIFT CABLE - CROSSOVER (Continued)
(8) Rock gearshift lever back and forth between
1–2 and 5–R planes. Release lever, allowing shifter
spring to return lever to the neutral position in the
3–4 plane. Place gearshift lever in the 3rd gear posi-
tion.
(9) Torque crossover lever adjustment screw to 8
N·m (70 in. lbs.). No load should be applied to
the shifter lever in any direction (hands off)
while tightening screw.
(10) Verify gearshift lever travel through all gear
ranges with engine off (not running).
(11) Install center console assembly (Fig. 168).
Install and torque center console-to-gearshift mecha-
nism screws to 5 N·m (45 in. lbs.).
(12) Install cupholder plugs (Fig. 167).
(13) Install gearshift boot to console (Fig. 166).
Secure boot to console with three (3) retainer clips.
(14) Install gearshift knob to gearshift lever (Fig.
165). Orient shift pattern on knob
1
⁄
4
-turn clockwise,
push down and rotate
1
⁄
4
-turn counter-clockwise and
release. Secure boot to knob.
(15) Connect battery negative cable.
GEARSHIFT CABLE -
SELECTOR
REMOVAL
(1) Disconnect battery negative cable.
(2) Remove gearshift knob by pushing down and
rotating
1
⁄
4
-turn clock-wise (Fig. 170).
(3) Remove gearshift boot from center console by
disengaging at three (3) retaining clips (Fig. 171).
(4) Apply park brake to allow park brake handle to
clear center console upon removal.
(5) Remove two (2) cupholder bottom plugs (Fig.
172).
Fig. 170 Gearshift Knob Removal/Installation
1 - GEARSHIFT KNOB
2 - GEARSHIFT LEVER
Fig. 171 Gearshift Boot Removal/Installation
1 - GEARSHIFT BOOT
2 - CENTER CONSOLE
Fig. 172 Cup Holder Plugs
1 - CUPHOLDER PLUG (2)
RG
T850 MANUAL TRANSAXLE
21a - 85
GEARSHIFT CABLE - CROSSOVER (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст