Chrysler RG Voyager. Manual — part 217
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Power Mirror connector.
Measure the resistance of the Mirror Sensor Ground circuit in the harness connector
to ground.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 4
No
→ Go To 5
4
If there are no possible causes remaining, view repair.
All
Repair
Replace the Power Mirror.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
5
Turn the ignition off.
Disconnect the Power Mirror connector.
Disconnect the Memory Seat/Mirror/Adjustable Pedals Module C1 connector.
Measure the resistance of Mirror Sensor Ground circuit between the Memory
Seat/Mirror/Adjustable Pedals Module connector and the Power Mirror connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Memory Seat/Mirror/Adjustable Pedals Module.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
No
→ Repair the open Sensor Ground circuit.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
6
Turn the ignition off.
Disconnect the Power Mirror connector.
Disconnect the Memory Seat/Mirror/Adjustable Pedals Module C1 connector.
Turn the ignition on.
Measure the voltage of Mirror Horizontal Position Signal circuit.
Is there any voltage present?
All
Yes
→ Repair the Mirror Horizontal Position Signal circuit for a short to
voltage.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
No
→ Go To 7
7
Turn the ignition off.
Disconnect the Memory Seat/Mirror/Adjustable Pedals Module C1 connector.
Disconnect the Power Mirror connector.
Measure the resistance of the Mirror Horizontal Position Signal circuit from the
Power Mirror connector to the Memory Seat/Mirror/Adjustable Pedals Module
connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Memory Seat/Mirror/Adjustable Pedals Module.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
No
→ Repair the open Mirror Horizontal Position Signal wire.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
837
MEMORY SEAT
DRIVER MIRROR HORIZONTAL SENSOR OUT OF RANGE HIGH —
Continued
Symptom:
DRIVER MIRROR HORIZONTAL SENSOR OUT OF RANGE LOW
When Monitored and Set Condition:
DRIVER MIRROR HORIZONTAL SENSOR OUT OF RANGE LOW
When Monitored:
Continuously when the PCI bus is active.
Set Condition:
This code is set when the mirror sensor feedback to the MSMAPM is less
than the mirror out of range low value stored in EEPROM. Code will remain for 50 ignition
cycles.
POSSIBLE CAUSES
MSMAPM HORIZONTAL POSITION LOW
STORED DIAGNOSTIC TROUBLE CODE
MIRROR HORIZONTAL POSITION SIGNAL WIRE SHORT TO GROUND
POWER MIRROR
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase the DTC from Memory Seat/Mirror/Adjustable Pedals
Module.
Operate the memory system.
Turn the ignition switch to the Off position then start the engine and let run for one
minute.
With the DRBIII
t check for the same DTC to reset in the MSMAPM.
Did the same DTC reset?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the Power Mirror connector.
Turn the ignition on.
Measure the voltage of the Mirror Horizontal Position Signal circuit in the Power
Mirror harness connector.
Is the voltage between 4.5 and 5.5 volts?
All
Yes
→ Replace the Power Mirror.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
No
→ Go To 3
838
MEMORY SEAT
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Memory Seat/Mirror/Adjustable Pedals Module C1 connector.
Disconnect the Power Mirror connector.
Measure the resistance of the Mirror Horizontal Position Signal circuit to ground at
the Power Mirror harness side connector.
Is the resistance below 1000.0 ohms?
All
Yes
→ Repair the Mirror Horizontal Position Signal wire for a short to
ground.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
No
→ Replace the Memory Seat/Mirror/Adjustable Pedals Module.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
839
MEMORY SEAT
DRIVER MIRROR HORIZONTAL SENSOR OUT OF RANGE LOW —
Continued
Symptom:
DRIVER MIRROR VERTICAL SENSOR OUT OF RANGE HIGH
When Monitored and Set Condition:
DRIVER MIRROR VERTICAL SENSOR OUT OF RANGE HIGH
When Monitored:
Continuously when the PCI bus is active.
Set Condition:
This code is set when the mirror sensor feedback to the Memory
Seat/Mirror/Adjustable Pedals Module is greater than the mirror out of range high value
stored in EEPROM. Code will remain for 50 ignition cycles.
POSSIBLE CAUSES
MIRROR SENSOR GROUND WIRE OPEN
MIRROR VERTICAL POSITION WIRE SHORTED TO VOLTAGE
STORED DIAGNOSTIC TROUBLE CODE
MIRROR VERTICAL POSITION SIGNAL OPEN
POWER MIRROR
MEMORY SEAT/MIRROR/ADJUSTABLE PEDALS MODULE SENSOR GROUND
MEMORY SEAT/MIRROR/ADJUSTABLE PEDALS MODULE VERTICAL POSITION SIGNAL
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase the DTC from Memory Seat/Mirror/Adjustable Pedals
Module.
Operate the memory system.
Turn the ignition switch to the Off position then start the engine and let run for one
minute.
With the DRBIII
t check for the same DTC to reset in the MSMAPM.
Did the same DTC reset?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform MEMORY SYSTEM VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the Power Mirror connector.
Turn the ignition on.
Measure the voltage of the Mirror Vertical Position Signal circuit in the Left Power
Mirror harness connector.
Is the voltage between 4.5 and 5.5 volts?
All
Yes
→ Go To 3
No
→ Go To 6
840
MEMORY SEAT
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст