Chrysler Le Baron, Dodge Dynasty, Plymouth Acclaim. Manual — part 175
APPLIQUE MOULDING AND RETAINER
REMOVAL
(1) Remove screws holding applique to rocker
panel from under vehicle.
(2) Lift applique upward to separate from retain-
ing channel.
(3) Remove pop-rivets holding retainer to rocker
panel using a suitable drill.
APPLIQUE MOULDING AND RETAINER
INSTALLATION
(1) Install applique retainer on rocker panel with
pop-rivets. Paint or undercoat bare metal surfaces to
avoid rust.
(2) Hook top of applique over retainer channel and
install screws under rocker panel.
COWL PANEL TRIM AND SCUFF PLATES
COWL PANEL AND DOOR OPENING SCUFF
PLATE REMOVAL (FIG. 30 OR 31)
(1) Open front door.
(2) Remove screw holding trim panel to cowl for-
ward of the front door opening.
(3) Remove screws holding scuff plate to door sill.
(4) Separate cowl panel trim and scuff plate from
vehicle.
COWL PANEL AND DOOR OPENING SCUFF
PLATE INSTALLATION
Reverse the preceding operation.
A-PILLAR AND ROOF RAIL MOULDINGS
A-PILLAR MOULDING REMOVAL (FIG. 30 OR
31)
(1) Open front door.
(2) Disengage clips holding A-pillar moulding to
roof rail above door opening.
(3) Slide A-pillar moulding upward and pull rear-
ward to separate moulding from A-pillar.
A-PILLAR MOULDING INSTALLATION
Reverse the preceding operation.
REAR DOOR ROOF RAIL MOULDING
REMOVAL—AP-44 BODY (FIG. 30)
(1) Open rear door.
(2) Disengage clips holding roof rail moulding to
roof rail above rear door opening.
(3) Separate moulding from vehicle.
REAR DOOR ROOF RAIL MOULDING
INSTALLATION—AP-44 BODY
Reverse the preceding operation.
B-PILLAR TRIM PANEL—AP-44 Body
REMOVAL (FIG. 30)
(1) Remove roof rail mouldings and scuff plates as
necessary.
(2) Remove shoulder harness turning loop cover.
Remove bolt holding turning loop to B-pillar.
(3) Remove bolt holding seat belt to floor below
B-pillar.
(4) Lift B-pillar trim off door opening sill weather-
strips and push inward.
(5) Slide B-pillar trim downward as far as possible
and separate trim from B-pillar.
INSTALLATION
Reverse the preceding operation.
UPPER QUARTER TRIM PANEL—AP-44 BODY
REMOVAL (FIG. 30)
(1) Remove roof rail mouldings as necessary.
(2) Remove shoulder harness turning loop cover.
Remove bolt holding turning loop to quarter panel.
(3) Remove rear seat as necessary to gain access to
quarter trim fasteners.
(4) Remove screws holding rear header moulding
to roof as necessary to clear quarter removal path.
(5) Remove screws holding upper quarter trim
panel to quarter panel.
(6) Disengage hook and loop fastener holding trim
to quarter panel.
(7) Pull trim panel forward and separate from ve-
hicle.
INSTALLATION
Reverse the preceding operation.
LOWER QUARTER TRIM PANEL—AP-44 BODY
REMOVAL (FIG. 30)
(1) Open rear door.
(2) Remove rear seat as necessary to gain access to
quarter trim fasteners.
(3) Remove screw holding lower quarter trim panel
to quarter panel.
(4) Separate lower quarter trim panel from vehicle.
INSTALLATION
Reverse the preceding operation.
QUARTER TRIM PANEL—AP-44 BODY
REMOVAL (FIG. 31)
(1) Remove roof rail mouldings and scuff plates as
necessary.
(2) Remove shoulder harness turning loop cover.
Remove bolt holding turning loop to quarter panel.
(3) Remove rear seat cushion, back, and rear bol-
ster.
Ä
AP-BODY
23 - 109
(4) Remove screws holding rear header moulding
to roof as necessary to clear quarter removal path.
(5) Remove screws holding upper quarter trim
panel to quarter panel.
(6) Disengage hook and loop fastener holding trim
to quarter panel.
(7) Pull trim panel forward and separate from ve-
hicle.
INSTALLATION
Reverse the preceding operation.
FRONT SEAT BELTS—AP-44 BODY
FRONT SHOULDER HARNESS/LAP BELT
REMOVAL (FIG. 32)
(1) Remove B-pillar trim panel.
(2) Remove bolt holding seat belt retractor to
B-pillar.
(3) Separate retractor from vehicle.
FRONT SHOULDER HARNESS/LAP BELT
INSTALLATION
Reverse the preceding operation.
FRONT INBOARD BUCKLE REMOVAL (FIG. 32)
(1) Remove bolt holding inboard buckle to floor.
(2) Disconnect seat belt sensor wire connector.
(3) Separate buckle assembly from vehicle.
FRONT INBOARD BUCKLE INSTALLATION
Reverse the preceding operation.
FRONT SEAT BELTS—AP-24 BODY
FRONT SHOULDER HARNESS/LAP BELT
REMOVAL (FIG. 33)
(1) Remove quarter trim panel as necessary.
(2) Remove bolt holding seat belt retractor quarter
panel.
(3) Remove bolt holding front lap belt anchor to
floor.
(4) Separate retractor from vehicle.
FRONT SHOULDER HARNESS/LAP BELT
INSTALLATION
Reverse the preceding operation.
FRONT INBOARD BUCKLE REMOVAL (FIG. 33)
(1) Remove bolt holding inboard buckle to floor.
(2) Disconnect seat belt sensor wire connector.
(3) Separate buckle assembly from vehicle.
FRONT INBOARD BUCKLE INSTALLATION
Reverse the preceding operation.
Fig. 30 Interior Mouldings, Panels, and Trim Covers—AP-44 Body
23 - 110
AP-BODY
Ä
REAR SEAT BELTS
REAR SHOULDER HARNESS/LAP BELT
REMOVAL (FIG. 34)
(1) Remove rear shoulder harness turning loop
cover. Remove bolt holding turning loop to roof
panel.
(2) Remove quarter trim panel, lower panel on AP-
44.
(3) Remove bolt holding lap belt to floor at wheel-
house kickup.
(4) Remove bolt holding seat belt retractor to quar-
ter panel.
REAR SHOULDER HARNESS/LAP BELT
INSTALLATION
Reverse the preceding operation.
REAR INBOARD BUCKLE/CENTER OCCUPANT
BELTS REMOVAL (FIG. 34)
(1) Remove rear seat cushion.
(2) Remove bolt holding inboard buckle/center oc-
cupant belt to floor.
(3) Separate buckle/belt assembly from vehicle.
REAR INBOARD BUCKLE/CENTER OCCUPANT
BELT INSTALLATION
Reverse the preceding operation.
FRONT SEATS
REMOVAL (FIG. 35 OR 36)
(1) Position seat full forward.
Fig. 31 Interior Mouldings, Panels, and Trim Covers—AP-24 Body
Fig. 32 Front Seat Belts—AP-44 Body
Ä
AP-BODY
23 - 111
(2) Remove screws holding rear track riser covers
and separate covers from tracks.
(3) On power seat track, remove outboard track
cover.
(4) Remove nuts holding seat track to floor.
(5) Position seat full rearward.
(6) On power seat track, remove door sill scuff
plate and disconnect wire connector.
(7) Remove bolts holding seat track to cross mem-
ber.
(8) Remove seat from vehicle.
INSTALLATION
Reverse the preceding operation.
REAR SEATS
REAR SEAT CUSHION REMOVAL
(1) Remove bolts holding cushion to floor.
(2) Push center occupant seat belts through open-
ings in cushion.
(3) Remove cushion from vehicle.
REAR SEAT CUSHION INSTALLATION
Reverse the preceding operation.
REAR SEAT BACK REMOVAL (FIG. 37)
(1) Hinge seat back forward and disengage push-in
fasteners holding carpet backing to trunk floor.
(2) Remove bolts holding outboard hinge pivot
bracket to seat back.
(3) Pull seat back outward to disengage inboard
pivot and separate from vehicle.
Fig. 33 Front Seat Belts—AP-24 Body
Fig. 34 Rear Seat Belts—Typical
Fig. 35 Manual Front Seat
Fig. 36 Power Front Seat
23 - 112
AP-BODY
Ä
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст