Chrysler Le Baron, Dodge Dynasty, Plymouth Acclaim. Manual — part 336
Fig. 3 Alignment Screws—AC and AY-Vehicles
Fig. 4 Alignment Screws— AA-Vehicle
Fig. 5 Alignment Screws— AC\-Vehicle
Fig. 6 Alignment Screws— AP-Vehicle
Fig. 7 Alignment Screws— AG and
AJ-Vehicle—Typical
Ä
LAMPS
8L - 5
Fig. 8 Fog Lamp Alignment
8L - 6
LAMPS
Ä
EXTERIOR LAMPS—AA BODY
INDEX
page
page
Center High-Mounted Stop Lamp (CHMSL) Bulb
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Front Side Marker Lamp or Bulb
. . . . . . . . . . . . . . . . . . . . . . . . . . . 7
. . . . . . . . . . . . . . . . . . . . . . . . . . . 7
License Plate Lamp or Bulb—AA/P Body
Park and Turn Signal Lamp or Bulb
Tail, Stop and Turn Signal and Back-Up Lamp
HEADLAMP BULB
REMOVAL (FIG. 1)
(1) Raise hood to the open position.
(2) Disconnect wire connector from lamp socket be-
hind the headlamp in the engine compartment.
(3) Rotate bulb retaining ring counterclockwise
one quarter turn and remove the ring from the lamp.
(4) Pull bulb from the lens assembly. When install-
ing bulb, align notches on bulb base to grooves in
lamp opening.
CAUTION: Do not touch the bulb with fingers or any
possibly oily surface, reduced bulb life will result.
INSTALLATION
Reverse the preceding operation.
HEADLAMP LENS
REMOVAL
(1) Raise hood to the open position.
(2) Disconnect wire connector from back of head-
lamp bulb.
(3) Remove screws holding side marker lamp to
front fender.
(4) Separate side marker lamp from fender and re-
move bulb socket from lamp.
(5) Remove screws holding headlamp to radiator
closure panel.
(6) Separate headlamp from radiator closure panel.
INSTALLATION
Reverse the preceding operation.
PARK AND TURN SIGNAL LAMP OR BULB
REMOVAL (FIG. 2)
(1) Remove screws holding park and turn signal
lamp to bumper fascia.
(2) Separate lamp from bumper fascia.
(3) Remove socket from lamp.
(4) Pull bulb from socket.
INSTALLATION
Reverse the preceding operation.
FRONT SIDE MARKER LAMP OR BULB
REMOVAL (FIG. 3)
(1) Remove lamp assembly attaching screws and
separate the lamp from the front fender opening.
(2) Rotate the side marker lamp socket counter-
clockwise one quarter turn and pull the socket and
bulb from the lamp.
(3) Remove the bulb from the socket.
Fig. 1 Aero Headlamp
Fig. 2 Park and Turn Signal Lamp
Ä
LAMPS
8L - 7
INSTALLATION
Reverse the preceding operation.
TAIL, STOP AND TURN SIGNAL AND BACK-UP
LAMP
REMOVAL (FIG. 4)
(1) Open deck lid and remove the plastic wing nut
securing the rear trim cover in place.
(2) Pivot the end of the trim panel out of the way
to gain access, and remove wing-nuts holding the
lamp to the vehicle.
(3) Separate the tail lamp from the body far
enough to rotate the socket and bulb assemblies. Ro-
tate sockets one-half turn and pull the sockets out of
the lamp body.
(4) Remove the bulb from the socket.
INSTALLATION
Reverse the preceding operation.
LICENSE PLATE LAMPS—AA/C Body
REMOVAL (FIG. 5)
(1) Remove screws holding license plate lamp to
rear bumper fascia.
(2) Separate license plate lamp from fascia.
(3) Remove socket from license plate lamp.
(4) Pull bulb from socket if bulb replacement is re-
quired.
INSTALLATION
Reverse the preceding operation.
LICENSE PLATE LAMP OR BULB—AA/P Body
REMOVAL (FIG. 6)
(1) Remove two lamp assembly attaching screws
above the rear license plate opening.
(2) Remove the lens from the deck-lid.
(3) Pull the bulb from the socket.
INSTALLATION
Reverse the preceding operation.
Fig. 3 Front Side Marker Lamps
Fig. 4 Rear Lighting—AA/P or AA/D Body
Fig. 5 License Plate Lamps—AA/C Body
Fig. 6 License Plate Lamp—AA/P Body
8L - 8
LAMPS
Ä
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст