Chrysler Pacifica. Manual — part 741
(4) Remove the 4 bolts.
(5) Remove short runner valve (Fig. 91).
INSTALLATION
(1) Install short runner valve (Fig. 92).
(2) Install the 4 bolts and tighten.
(3) Install the link to short runner valve lever
(Fig. 93).
(4) Connect the electrical connector to the short
runner valve (Fig. 94).
(5) Connect the negative battery cable.
Fig. 91 SHORT RUNNER VALVE SOLENOID
REMOVED
Fig. 92 SHORT RUNNER VALVE SOLENOID
REMOVED
Fig. 93 SOLENOID LINK REMOVED
Fig. 94 SHORT RUNNER VALVE
CS
FUEL INJECTION
14 - 55
SHORT RUNNER VALVE SOLENOID (Continued)
STEERING
TABLE OF CONTENTS
page
page
STEERING
DESCRIPTION - POWER STEERING SYSTEM
OPERATION - POWER STEERING SYSTEM
. . . . . . . . . . . . . . . 1
STEERING FLOW AND PRESSURE TEST . . . . 1
DIAGNOSIS AND TESTING - STEERING
SYSTEM DIAGNOSIS CHARTS . . . . . . . . . . . . 3
POWER STEERING FASTENER TORQUE
. . . . . . . . . . . . . . . . . . . . 10
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
STEERING
DESCRIPTION - POWER STEERING SYSTEM
This vehicle comes with power steering as stan-
dard equipment. The power steering system consists
of these major components:
• POWER STEERING PUMP
• POWER STEERING GEAR
• POWER STEERING FLUID
• POWER STEERING FLUID RESERVOIR
• POWER STEERING SUPPLY HOSE (3.5L
ENGINE)
• POWER STEERING PRESSURE HOSE
• POWER STEERING RETURN HOSE
For information on the first two components, refer
to their respective sections within this service man-
ual group. Information on all other components can
be found in POWER STEERING PUMP.
OPERATION - POWER STEERING SYSTEM
Turning of the steering wheel is converted into lin-
ear (side-to-side) travel through the meshing of the
helical pinion teeth with the rack teeth within the
steering gear. The lateral travel pushes and pulls the
tie rods to change the direction of the vehicle’s front
wheels.
Power assist steering is provided by a belt driven
rotary type pump. It directs fluid through power
steering fluid hoses to the power steering gear where
it is used to assist the driver’s turning effort.
Manual steering control of the vehicle can be main-
tained if power steering assist is lost. However,
under this condition, steering effort is significantly
increased.
WARNINGS AND CAUTIONS
WARNING:
POWER
STEERING
FLUID,
ENGINE
PARTS
AND
EXHAUST
SYSTEM
MAY
BE
EXTREMELY HOT IF ENGINE HAS BEEN RUNNING.
DO NOT START ENGINE WITH ANY LOOSE OR DIS-
CONNECTED HOSES. DO NOT ALLOW HOSES TO
TOUCH HOT EXHAUST MANIFOLD OR CATALYST.
WARNING: FLUID LEVEL SHOULD BE CHECKED
WITH THE ENGINE OFF TO PREVENT PERSONAL
INJURY FROM MOVING PARTS.
CAUTION: When the system is open, cap all open
ends of the hoses, power steering pump fittings or
power steering gear ports to prevent entry of for-
eign material into the components.
CAUTION: When servicing power steering compo-
nents, do not pinch off power steering hoses in an
any way to stop fluid flow. Damage to hoses may
result.
DIAGNOSIS AND TESTING
DIAGNOSIS AND TESTING - POWER STEERING
FLOW AND PRESSURE TEST
WARNING:
TO
PREVENT
PERSONAL
INJURY,
SAFETY GOGGLES SHOULD BE WORN AT ALL
TIMES WHILE PERFORMING ANY TEST PROCE-
DURES ON THE POWER STEERING SYSTEM.
The following procedure is to be used to test the
operation of the power steering system on this vehi-
CS
STEERING
19 - 1
cle. This test will provide the flow rate of the power
steering pump along with the maximum relief pres-
sure. This test is to be performed any time a power
steering system problem is present to determine if
the power steering pump or power steering gear is
not functioning properly. The following flow and pres-
sure test is performed using the Power Steering Ana-
lyzer Kit, Special Tool 6815 (Fig. 1), hoses, Special
Tools 6905 and 6959, and adapters, Special Tool
8185A.
(1) Assemble hoses on Power Steering Analyzer as
shown (Fig. 1). Install Pressure Hose, Special Tool
6959, in inlet fitting (gauge end) of Power Steering
Analyzer flow meter. Install Pressure Hose, Special
Tool 6905 (in 6893 kit), into outlet fitting (valve end)
of Power Steering Analyzer flow meter. Install Pres-
sure Hose, Special Tool 6713 (in 6815 kit) on 6905.
(2) Install Adapter, Special Tool 8185-1A, in end of
Pressure Hose, Special Tool 6713.
(3) Install Adapter, Special Tool 8185-2, in end of
Pressure Hose, Special Tool 6959.
(4) Raise and support vehicle. (Refer to LUBRICA-
TION & MAINTENANCE/HOISTING - STANDARD
PROCEDURE)
(5) Unscrew tube nut and remove power steering
fluid pressure hose from power steering gear (Fig. 2).
(6) Thread vehicle’s power steering pressure hose
into Adapter, Special Tool 8185-2, connected to Ana-
lyzer Hose (Fig. 3). Tighten tube nut to specifications
(Refer to 19 - STEERING - SPECIFICATIONS).
Route hoses away from exhaust system as well as
other unfriendly surfaces.
(7) Thread Adapter, Special Tool 8185-1A, con-
nected to Analyzer hose, into open power steering
gear port (Fig. 3). Tighten tube nut to specifications
(Refer to 19 - STEERING - SPECIFICATIONS).
Route hoses away from exhaust system as well as
other unfriendly surfaces.
(8) Being careful not to kink or pinch Analyzer
hoses, lower vehicle to ground level.
Fig. 1 Power Steering Analyzer With Hoses Installed
1 - SPECIAL TOOL 6815
2 - SPECIAL TOOL 6959
3 - SPECIAL TOOL 8185-2
4 - SPECIAL TOOL 6905 & 6713-1
Fig. 2 Hoses At Steering Gear
1 - POWER STEERING GEAR
2 - RETURN HOSE
3 - PRESSURE HOSE
4 - TUBE NUTS
Fig. 3 Analyzer Connections At Gear
1 - HOSE 6713
2 - POWER STEERING GEAR
3 - PRESSURE HOSE
4 - ADAPTER 8185-2
5 - HOSE 6959
6 - ADAPTER 8185-1A
19 - 2
STEERING
CS
STEERING (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст