Chrysler Pacifica. Manual — part 732
(8) Remove the center exhaust hanger rubber gro-
ments (Fig. 52).
(9) Remove the rear portion of the exhaust system
and set on floor.
(10) Disconnect the fuel tank electrical connector
(Fig. 53).
(11) Disconnect the fuel line and EVAP line (Fig.
54).
EXHAUST HANGER
Fig. 52 EXHAUST HANGER REMOVED
Fig. 53 FUEL TANK ELECTRICAL CONNECTOR
Fig. 54 FUEL SUPPLY LINE AND EVAP LINES
1 - EVAP Line
2 - Fuel Line
CS
FUEL DELIVERY
14 - 19
FUEL TANK (Continued)
(12) Disconnect the vapor recirculation tube (Fig.
55).
(13) Mark the driveshaft rear connection (Fig. 56).
(14) Disconnect the driveshaft rear connection
(Fig. 57).
(15) Remove the driveshaft support/bearing (Fig.
58).
Fig. 55 FUEL TANK VAPOR RECIRCULATION TUBE
Fig. 56 MARKING DRIVESHAFT
Fig. 57 DRIVESHAFT REAR CONNECTION
Fig. 58 DRIVESHAFT SUPPORT/BEARING
14 - 20
FUEL DELIVERY
CS
FUEL TANK (Continued)
(16) Support driveshaft on jack.
(17) Remove the left rear tire and splash shield.
(18) Remove the fuel filler tube from the rubber
hose at fuel tank (Fig. 59).
(19) Support the fuel tank with a transmission
jack.
(20) Remove the 2 fuel tank straps (Fig. 60).
(21) Lower fuel tank
(22) Drain Fuel Tank, use an approved GASO-
LINE draining station.
(23) Remove tank from vehicle (Fig. 61).
FUEL FILLER TUBE
Fig. 59 FILLER TUBE TO RUBBER HOSE
Fig. 60 FUEL TANK STRAPS
Fig. 61 FUEL TANK ASSEMBLY
CS
FUEL DELIVERY
14 - 21
FUEL TANK (Continued)
INSTALLATION
(1) Support the fuel tank with a transmission jack.
(2) Raise fuel tank and install to vehicle (Fig. 61).
(3) Install the 2 fuel tank straps (Fig. 60).
(4) Install the fuel filler tube to the rubber hose at
fuel tank (Fig. 59).
(5) Connect the vapor recirculation tube (Fig. 55).
(6) Connect the fuel line and EVAP line.
(7) Connect the fuel tank electrical connector (Fig.
53).
(8) Support driveshaft on jack.
(9) Install the driveshaft support/bearing (Fig. 58).
(10) Align the Marks on the driveshaft to the rear
connection.
(11) Connect the driveshaft rear connection (Fig.
57).
(12) Install the exhaust system and tighten clamp.
(13) Install the center exhaust hanger rubber gro-
ments (Fig. 52).
(14) Install muffler hanger rubber groments (Fig.
51).
(15) Install the left rear tire.
(16) Lower vehicle.
(17) Connect the negative battery cable.
(18) Fill fuel tank. Use the DRBIII
t scan tool to
pressurize the fuel system. Check for leaks.
FUEL TANK FILLER TUBE
REMOVAL
(1) Release the fuel pressure, refer to the Fuel
Pressure Release Procedure in this section.
(2) Disconnect the negative battery cable.
(3) Raise vehicle and support.
(4) Remove the left rear tire.
(5) Remove the left rear splash shield.
(6) Remove 3 screws from filler neck to quarter
panel (Fig. 62).
(7) Disconnect the vent line to filler tube.
(8) Remove the fuel filler tube from the rubber
hose at fuel tank (Fig. 63).
(9) Remove the filler tube.
FUEL FILLER TUBE
Fig. 62 FILLER TUBE
Fig. 63 FILLER TUBE TO RUBBER HOSE
14 - 22
FUEL DELIVERY
CS
FUEL TANK (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст