Chrysler Pacifica. Manual — part 829
INSTALLATION
(1) Place the liftgate light bar wiring harness
through liftgate.
(2) Line up the four liftgate light bar retaining
screws and install (Fig. 5) and (Fig. 6).
(3) Connect the liftgate light bar electrical connec-
tor inside the liftgate.
(4) Install the liftgate inner trim panel (Refer to
23 - BODY/INTERIOR/LIFTGATE TRIM PANEL -
INSTALLATION).
(5) Connect the battery negative cable.
(6) Verify vehicle and system operation.
(7) Close hood.
PROP ROD ASSEMBLY
REMOVAL
(1) Open the liftgate and support.
(2) Using a small flat bladed tool, or equivalent,
release the retaining clips while pulling the ball
socket away from the ball stud. (Fig. 7)
NOTE: Lift the clips only enough to release the ball
studs. (Fig. 8)
(3) Remove the support cylinder.
Fig. 6 LIFTGATE LIGHT BAR - REMOVE/INSTALL
1 - LIFTGATE LIGHT BAR HARNESS GROMMET
2 - LIFTGATE LIGHT BAR
3 - LIFTGATE
4 - OUTER LIFTGATE PANEL
5 - LIFTGATE LIGHT BAR ELECTRICAL CONNECTOR
6 - LIFTGATE WIRING HARNESS
7 - INNER LIFTGATE PANEL
Fig. 7 SUPPORT CYLINDER REMOVAL
1 - BALL SOCKET
2 - RETAINING CLIP
3 - FLAT BLADED TOOL
4 - BALL STUD
CS
LIFTGATE
23 - 111
LIFTGATE LIGHT BAR (Continued)
INSTALLATION
(1) Make sure the retaining clips are seated into
the ball socket fully.
(2) Install the support cylinder over the ball studs
with the thin end connected to the liftgate and the
retaining clips snapping into place.
SLAM BUMPER
REMOVAL
REMOVAL - BODY SIDE
(1) Open liftgate.
(2) Remove liftgate stop bumper body side attach-
ing bolts (Fig. 9).
(3) Remove liftgate stop bumper.
REMOVAL - LIFTGATE SIDE
(1) Open liftgate.
(2) Remove
liftgate
stop
bumper
liftgate
side
attaching rivets by drilling out old rivets (Fig. 9).
Recover rivet chips from inside of liftgate to prevent
rattles.
(3) Remove liftgate stop bumper.
INSTALLATION
INSTALLATION - BODY SIDE
(1) Place liftgate stop bumper into position.
(2) Install screws attaching liftgate stop bumper to
body (Fig. 9).
(3) Close liftgate.
INSTALLATION - LIFTGATE SIDE
(1) Place liftgate stop bumper into position.
(2) Install rivets attaching liftgate stop bumper to
liftgate (Fig. 9).
(3) Close liftgate.
Fig. 8 SUPPORT CYLINDER RETAINING CLIP
1 - RETAINING CLIP
2 - BALL SOCKET
3 - BALL STUD
Fig. 9 LIFTGATE BUMPERS
1 - BLIND RIVET REPLACE
2 - LIFTGATE BUMPER
3 - LIFTGATE INNER PANEL
4 - LIFTGATE OPENING DRAIN TROUGH
5 - ATTACHING SCREW(S) AND WASHER(S)
6 - LIFTGATE TROUGH LOW ENGAGEMENT BUMPER
23 - 112
LIFTGATE
CS
PROP ROD ASSEMBLY (Continued)
TRIM PANEL
REMOVAL
REMOVAL - UPPER
(1) Release liftgate latch and open liftgate.
(2) Disconnect power liftgate link from ball head
bracket, if equipped (Fig. 10). (Refer to 8 - ELECTRI-
CAL/POWER DOORS/CONTROL ROD - REMOVAL).
(3) Using a trim stick C-4755 or equivalent, disen-
gage the upper trim panel locking tabs.
(4) Remove upper trim panel from liftgate.
REMOVAL - LOWER
(1) Release liftgate latch and open liftgate.
(2) Remove liftgate upper trim panel. (Refer to 23 -
BODY/DECKLID/HATCH/LIFTGATE/TAILGATE/
TRIM PANEL - REMOVAL).
(3) Remove two (2) upper screws attaching trim
panel (Fig. 11).
(4) Remove six (6) lower screws attaching trim
panel.
(5) Remove liftgate trim panel from vehicle.
(6) Gently pull trim panel away from liftgate to
disengage pins and grommets.
(7) Remove trim panel from vehicle.
Fig. 10 LIFTGATE UPPER TRIM PANEL
1 - PINS AND GROMMETS
2 - CLIPS
3 - FOUR (4) WAY LOCATOR
4 - UPPER LIFTGATE TRIM PANEL - MANUAL LIFTGATE
5 - POWER LIFTGATE LINK
6 - UPPER LIFTGATE TRIM PANEL - POWER LIFTGATE
Fig. 11 LIFTGATE LOWER TRIM PANEL
1 - LIFTGATE LOWER TRIM PANEL
2 - LOCATING PIN
3 - LOWER TRIM PANEL UPPER SCREW(S)
4 - LIFTGATE
5 - LOWER TRIM PANEL LOWER SCREW(S)
CS
LIFTGATE
23 - 113
INSTALLATION
INSTALLATION - UPPER
(1) Place upper trim panel into position.
(2) Press the upper trim panel locking tabs into
the locked position (Fig. 10).
(3) Connect power liftgate link onto ball head
bracket, if equipped. (Refer to 8 - ELECTRICAL/
POWER
DOORS/CONTROL
ROD
-
INSTALLA-
TION).
(4) Close liftgate.
INSTALLATION - LOWER
(1) Check for missing grommets or plastic nuts
(Fig. 12).
(2) Place lower trim panel into position (Fig. 11).
(3) Push trim panel against liftgate to engage pins
and grommets.
(4) Install six (6) lower screws attaching trim
panel.
(5) Install two (2) upper screws attaching trim
panel.
(6) Install liftgate upper trim panel. (Refer to 23 -
BODY/DECKLID/HATCH/LIFTGATE/TAILGATE/
TRIM PANEL - INSTALLATION).
(7) Close liftgate.
Fig. 12 LIFTGATE TRIM PANEL GROMMETS AND
PLASTIC NUTS
1 - GROMMETS
2 - PLASTIC NUTS
23 - 114
LIFTGATE
CS
TRIM PANEL (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст