Chrysler Pacifica. Manual — part 243
TEST
ACTION
APPLICABILITY
3
Disconnect the Driver Rear Riser Seat Position Sensor connector.
Measure the voltage between Driver Seat Sensor 5 volt supply circuit and ground.
Turn ignition on.
Is the voltage above 5.5 volts?
All
Yes
→ Repair the Driver Seat Sensor 5 Volt Supply circuit for a short to
battery.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER
1.
No
→ Go To 4
4
Turn ignition off.
Disconnect the Driver Rear Riser Seat Position Sensor Connector.
Disconnect the MHSAPM C2 Connector.
Turn ignition on.
Measure the voltage between Driver Seat Rear Riser Seat Position Signal circuit and
ground.
Is the voltage above 0.2 volts?
All
Yes
→ Repair the Driver Seat Rear Riser Position Signal circuit for a
short to voltage.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER
1.
No
→ Go To 5
5
Turn ignition off.
Disconnect the Driver Rear Riser Seat Position Sensor Connector.
Ensure the MHSAPM is fully connected before proceeding.
Turn ignition on.
With the DRBIII
t in Body MHSAPM Sensors
Read the Driver Seat Rear Riser Sensor voltage.
Is the voltage above 0.2 volts?
All
Yes
→ Go To 6
No
→ Replace the Seat Track Assembly.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER 1.
6
Ensure all seat and sensor connectors are connected and rear riser motor is
operational.
With the DRBIII
t in MHSAPM Sensors monitor the Driver Seat Rear Riser sensor
while operating the seat rear riser to both limits.
Did the voltage ever go above 7.0 volts only when the motor was in operation?
All
Yes
→ Replace the Seat Track Assembly.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER
1.
No
→ Go To 7
7
If there are no possible causes remaining, view repair.
All
Repair
Replace the Memory/Heated Seat Adjustable Pedal Module.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER 1.
969
POWER SEATS
DRIVER REAR RISER SENSOR OUT OF RANGE HIGH - MHSAPM —
Continued
TEST
ACTION
APPLICABILITY
8
Turn ignition off.
Disconnect the MHSAPM C2 connector.
Disconnect the Driver Rear Riser Seat Position Sensor connector.
Measure the resistance of the Driver Seat Position Sensor Ground wire between the
Driver Rear Riser Seat Position Sensor connector and the C2 connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Memory/Heated Seat Adjustable Pedal Module.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER
1.
No
→ Repair the Driver Seat Position Sensor Ground wire for an open.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER 1.
970
POWER SEATS
DRIVER REAR RISER SENSOR OUT OF RANGE HIGH - MHSAPM —
Continued
Symptom:
DRIVER REAR RISER SENSOR OUT OF RANGE LOW - MHSAPM
When Monitored and Set Condition:
DRIVER REAR RISER SENSOR OUT OF RANGE LOW - MHSAPM
When Monitored:
Continuously.
Set Condition:
This code is immediately set when the seat motor potentiometer feeds a
value lower than the Memory/Heated Seat Adjustable Pedal Module has stored in
EEPROM. Code will remain for 50 ignition cycles.
POSSIBLE CAUSES
DRIVER SEAT SENSOR 5 VOLT SUPPLY WIRE OPEN
DRIVER SEAT SENSOR 5 VOLT SUPPLY WIRE SHORT TO GROUND
MEMORY/HEATED SEAT ADJUSTABLE PEDAL MODULE 5 VOLT SUPPLY
DRIVER SEAT REAR RISER POSITION SIGNAL CIRCUIT OPEN
DRIVER SEAT REAR RISER POSITION SIGNAL CIRCUIT SHORT TO GROUND
DRIVER REAR RISER SEAT POSITION SENSOR LOW
MEMORY/HEATED SEAT ADJUSTABLE PEDAL MODULE REAR RISER LOW
STORED DIAGNOSTIC TROUBLE CODE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase the DTC from the Memory/Heated Seat Adjustable Pedal
Module (MHSAPM).
Operate the driver’s power seat and memory system.
Turn the ignition switch to the Off position then start the engine and let run for one
minute.
With the DRBIII
t check for the same DTC to reset in the MHSAPM.
Did the same DTC reset?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER 1.
2
Ensure the MHSAPM is fully connected before proceeding.
Disconnect the Driver Rear Riser Seat Position Sensor connector.
Turn ignition on.
Measure the voltage of the Driver Seat Sensor 5 Volt Supply circuit at rear riser
connector.
Is the voltage above 4.5 volts?
All
Yes
→ Go To 3
No
→ Go To 7
971
POWER SEATS
TEST
ACTION
APPLICABILITY
3
Turn ignition off.
Disconnect the Driver Rear Riser Seat Position Sensor Connector.
Disconnect the MHSAPM C2 Connector.
Measure the resistance of the Driver Seat Rear Riser Position Signal circuit between
the rear riser sensor and the MHSAPM C2 connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the Driver Seat Rear Riser Position Signal circuit for an
open.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER 1.
4
Turn ignition off.
Disconnect the MHSAPM C2 connector.
Disconnect the Driver Rear Riser Seat Position Sensor connector.
Measure the resistance of the Driver Seat Rear Riser Position Signal circuit to
ground.
Is the resistance below 1000 ohms?
All
Yes
→ Repair the Driver Seat Rear Riser Position Signal circuit a short
to ground.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER
1.
No
→ Go To 5
5
Turn ignition off.
Ensure the MHSAPM is fully connected before proceeding.
Disconnect the Driver Rear Riser Seat Position Sensor Connector.
Connect a jumper wire between Driver Seat Sensor 5 volt Supply and Driver Seat
Rear Riser Position Signal circuits.
Turn ignition on.
With the DRBIII
t select MHSAPM Sensors.
Read the Driver Seat Rear Riser Sensor voltage.
Is the voltage above 4.5 volts?
All
Yes
→ Replace the Seat Track Assembly.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER
1.
No
→ Go To 6
6
If there are no possible causes remaining, view repair.
All
Repair
Replace the Memory/Heated Seat Adjustable Pedal Module.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER 1.
7
Turn ignition off.
Disconnect the MHSAPM C2 connector.
Disconnect the Driver Rear Riser Seat Position Sensor connector.
Measure the resistance of the Driver Seat Sensor 5 Volt Supply wire between the
Rear Riser Sensor connector and the C2 connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 8
No
→ Repair the Driver Seat Sensor 5 Volt Supply circuit for an open.
Perform POWER SEAT SYSTEM VERIFICATION TEST - VER 1.
972
POWER SEATS
DRIVER REAR RISER SENSOR OUT OF RANGE LOW - MHSAPM —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст