Chrysler Pacifica. Manual — part 334
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the MAP Sensor harness connector.
Ignition on, engine not running.
Measure the voltage of the (K1) MAP Signal circuit in the MAP Sensor harness
connector.
Is the voltage above 5.2 volts?
All
Yes
→ Repair the short to battery voltage in the (K1) MAP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No
→ Go To 4
4
Turn the ignition off.
Disconnect the MAP Sensor harness connector.
Connect a jumper wire between the (K1) MAP Sensor Signal circuit and the (K4)
Sensor ground circuit.
With the DRBIII
t, monitor the MAP Sensor voltage.
Ignition on, engine not running.
Is the voltage below 1.0 volt?
All
Yes
→ Replace the MAP Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No
→ Go To 5
5
Turn the ignition off.
Disconnect the MAP Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K1) MAP Signal circuit from the MAP Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 6
No
→ Repair the open in the (K1) MAP Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
6
Turn the ignition off.
Disconnect the MAP Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K4) Sensor ground circuit from the MAP Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 7
No
→ Repair the open in the (K4) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
57
DRIVEABILITY - NGC
P0108-MAP SENSOR HIGH —
Continued
TEST
ACTION
APPLICABILITY
7
NOTE: Before continuing, check the PCM harness connector terminals for
corrosion, damage, or terminal push out. Repair as necessary.
If there are no possible causes remaining, view repair.
All
Repair
Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
58
DRIVEABILITY - NGC
P0108-MAP SENSOR HIGH —
Continued
Symptom:
P0111-INTAKE AIR TEMPERATURE SENSOR PERFORMANCE
When Monitored and Set Condition:
P0111-INTAKE AIR TEMPERATURE SENSOR PERFORMANCE
When Monitored:
Engine off time is greater than 480 minutes. Ambient temperature is
greater than -23°C (-10°F).
Set Condition:
After a calibrated amount of cool down time, the PCM compares the ECT
Sensor, IAT Sensor and the Ambient Air Temperature Sensor values. If the IAT Sensor
value is not within calibrated temperature amount of the other two temperature sensors
an error is detected. Two Trip Fault.
POSSIBLE CAUSES
GOOD TRIP EQUAL TO ZERO
(K21) IAT SIGNAL CIRCUIT SHORTED TO BATTERY VOLTAGE
IAT SENSOR VOLTAGE BELOW 1.0 VOLTS
(K21) IAT SIGNAL CIRCUIT OPEN
(K4) SENSOR GROUND CIRCUIT OPEN
(K21) IAT SIGNAL SHORTED TO GROUND
(K21) IAT SIGNAL CIRCUIT SHORTED TO (K4) SENSOR GROUND
PCM HIGH
PCM LOW
TEST
ACTION
APPLICABILITY
1
Ignition on, engine not running.
With the DRBIII
t, read DTCs and record the related Freeze Frame data.
Is the Good Trip Counter displayed and equal to zero?
All
Yes
→ Go To 2
No
→ Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
2
Turn the ignition off.
Disconnect the IAT Sensor harness connector.
NOTE: Visually inspect both the component and the PCM connectors. Look
for damaged, partially broken wires, and backed out or corroded terminals.
Ignition on, engine not running.
Measure the voltage on the (K21) IAT Signal circuit in the IAT Sensor harness
connector.
Is the voltage above 5.2 volts?
All
Yes
→ Repair the short to battery voltage in the (K21) IAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No
→ Go To 3
59
DRIVEABILITY - NGC
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the IAT Sensor harness connector.
Ignition on, engine not running.
With the DRBIII
t, read the IAT Sensor voltage.
Is the voltage above 4.9 volts?
All
Yes
→ Go To 4
No
→ Go To 7
4
Turn the ignition off.
Disconnect the IAT Sensor harness connector.
Using a jumper wire, jumper across the IAT Sensor harness connector.
Ignition on, engine not running.
With the DRBIII
t, read the IAT Sensor voltage.
Is the voltage below 1.0 volt?
All
Yes
→ Replace the IAT Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No
→ Go To 5
5
Turn the ignition off.
Disconnect the IAT Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K21) IAT Signal circuit from the IAT Sensor harness
connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 6
No
→ Repair the open in the (K21) IAT Signal circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
6
Turn the ignition off.
Disconnect the IAT Sensor harness connector.
Disconnect the PCM harness connector.
CAUTION: DO NOT PROBE THE PCM HARNESS CONNECTORS. PROBING
THE PCM HARNESS CONNECTORS WILL DAMAGE THE PCM TERMI-
NALS RESULTING IN POOR TERMINAL TO PIN CONNECTION. INSTALL
MILLER SPECIAL TOOL #8815 TO PERFORM DIAGNOSIS.
Measure the resistance of the (K4) Sensor ground circuit from the IAT Sensor
harness connector to the appropriate terminal of special tool #8815.
Is the resistance below 5.0 ohms?
All
Yes
→ NOTE: Before continuing, check the PCM harness connector
terminals for corrosion, damage, or terminal push out. Repair as
necessary. Replace and program the Powertrain Control Module
in accordance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
No
→ Repair the open in the (K4) Sensor ground circuit.
Perform POWERTRAIN VERIFICATION TEST VER - 5.
60
DRIVEABILITY - NGC
P0111-INTAKE
AIR
TEMPERATURE
SENSOR
PERFORMANCE
—
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст