Chrysler Pacifica. Manual — part 804
SPECIFICATIONS
SPECIFICATIONS
TIGHTENING SPECIFICATIONS
DESCRIPTION
N·m
Ft. Lbs.
In. Lbs.
Front Seat to Floor Nuts
88 N·m
65 ft. lbs.
—
First Row Seat to Floor Nuts
54 N·m
40 ft. lbs.
—
Second Row to Floor Nuts
54 N·m
40 ft. lbs.
—
Seat Belt Web Guide to B-Pillar
10 N·m
—
90 in. lbs.
Seat Belt Retractor Bolt
41 N·m
30 ft. lbs.
—
Second Row Seat Belt Bracket
40 N·m
30 ft. lbs.
—
Seat Belt Web Guide Screw
11 N·m
—
100 in. lbs.
Upper & Lower Portion of Retractor Screws
40 N·m
30 ft. lbs.
—
Seat Belt Turning Loop Button Adjuster Screws
40 N·m
30 ft. lbs.
—
Front Door Outside Mirror Nuts
6 N·m
—
50 in. lbs.
Floor Console to Floor
12 N·m
—
105 in. lbs.
Video Bracket to Roof Bow
12 N·m
—
105 in. lbs.
Sunroof to Roof Module
12 N·m
—
105 in. lbs.
Outside Door Handle Bracket Sub-Assemble Screw
4 N·m
—
37 in. lbs.
Front Door Power Latch and Cable Screws
9 N·m
—
80 in. lbs.
Door Hold Open Check Strap Nuts
10 N·m
—
90 in. lbs.
Door Check Strap Screws
12 N·m
—
105 in. lbs.
Outside Handle Cover Fastener
4 N·m
—
37 in. lbs.
Front and Rear Door hinge To Body
34 N·m
—
25 ft. lbs.
Front and Rear Door hinge To Door
34 N·m
25 ft. lbs.
Front Door Latch Striker to B-Pillar Screws
28 N·m
—
250 in. lbs.
Front Door Outside B-Pillar Applique Molding
3 N·m
—
30 in. lbs.
Front Door Glass Run Lower Channel Screw
6 N·m
—
55 in. lbs.
Front Door Power Regulator Screw
9 N·m
—
80 in. lbs.
Rear Door B/C-Pillar Applique Molding Screw
3 N·m
—
30 in. lbs.
Rear Door Power Lock Latch Screw
8 N·m
—
75 in. lbs.
Rear Door Outside Handle Bracket Fastener
4 N·m
—
37 in. lbs.
Rear Door Outside Handle Fastener
4 N·m
—
37 in. lbs.
Rear Door Fixed Glass Run Screw
5 N·m
—
45 in. lbs.
Rear Door Power Regulator Screw
9 N·m
—
80 in. lbs.
Liftgate Prop Rod Bracket Screws
40 N·m
—
350 in. lbs.
Liftgate Prop Rod Stud
36 N·m
—
320 in. lbs.
Liftgate Outside Handle to Liftgate screw
9 N·m
—
80 in. lbs.
Liftgate Latch to Liftgate Screw
11 N·m
—
95 in. lbs.
Liftgate Light Bar to liftgate screws
2 N·m
—
20 in. lbs.
Liftgate Bumper to Drain Trough screw
6 N·m
—
55 in. lbs.
Liftgate Latch Striker
28 N·m
—
250 in. lbs.
CS
BODY
23 - 11
BODY (Continued)
DESCRIPTION
N·m
Ft. Lbs.
In. Lbs.
Liftgate Spoiler to Liftgate Outer Nuts
7 N·m
—
60 in. lbs.
Hood Latch to Radiator Crossmember Screws
14 N·m
—
120 in. lbs.
Hood Striker to Hood
14 N·m
—
120 in. lbs.
Hood Hinge to hood
14 N·m
—
120 in. lbs.
Hood Hinge Pivot Bolt
28 N·m
—
250 in. lbs.
Hood Hinge to Fender
9 N·m
80 in. lbs.
Hood Emblem Bright Outer Molding Nuts
4 N·m
—
35 in. lbs.
Instrument Panel to Cowl Side
28 N·m
—
250 in. lbs.
Instrument Panel Column Support Bracket Nuts
23 N·m
17 ft. lbs.
—
Instrument Panel Floor Bracket Brace to Floor Nuts
17 N·m
—
150 in. lbs.
Instrument Panel Floor Bracket to Center Stack Brace
Nuts
17 N·m
—
150 in. lbs.
Instrument Panel Plenum Screws
7 N·m
—
60 in. lbs.
Instrument Panel Reinforcement Brace
9 N·m
—
80 in. lbs.
Front & Rear Console Side Walls to Structure Duct
2 N·m
—
20 in. lbs.
Cargo Load Floor Bin Screws
12 N·m
—
105 in. lbs.
Automatic Transaxle Shifter Knob
2 N·m
—
20 in. lbs.
Autostick Shifter Nut
12 N·m
—
105 in. lbs.
BODY LUBRICATION
LUBRICATION REQUIREMENTS
Body
mechanisms
and
linkages
should
be
inspected, cleaned, and lubricated, as required, to
maintain ease of operation and to provide protection
against rust and wear. When performing other under
hood services, the hood latch release mechanism and
safety catch should be inspected, cleaned, and lubri-
cated. During the winter season, external door lock
cylinders should be lubricated to assure proper oper-
ation when exposed to water and ice.
Prior to the application of any lubricant, the parts
concerned should be wiped clean to remove dust and
grit. If necessary, a suitable solvent can be used to
clean the item to be lubricated. After lubricating a
component, any excess oil or grease should be
removed.
LUBRICANT APPLICATION
DOOR LOCK CYLINDERS
(1) Apply a small amount of lubricant directly into
the lock cylinder.
(2) Apply a small amount of lubricant to the key.
(3) Insert key into lock cylinder and cycle the
mechanism from the locked to the unlocked position.
NOTE: Do not add more lubricant.
(4) Cycle the lock cylinder mechanism several
times to allow the lubricant to flow throughout the
cylinder.
(5) Wipe all lubricant from exterior of lock cylinder
and key.
ALL OTHER BODY MECHANISMS
(1) Clean component as described above.
(2) Apply specified lubricant to all pivoting and
sliding contact areas of component.
LUBRICANT USAGE
ENGINE OIL
• Door Hinges – Hinge Pin and Pivot Contact
Areas
• Hood Hinges – Pivot Points
• Liftgate Hinges
MOPAR
T
SPRAY WHITE LUBE OR EQUIVALENT
• Door Check Straps
• Liftgate Latches
• Liftgate Prop Pivots
• Ash Receiver
• Parking Brake Mechanism
• Sliding Seat Tracks
• Liftgate Latch
MOPAR
T
Multipurpose GREASE OR EQUIVALENT
• All Other Hood Mechanisms
23 - 12
BODY
CS
BODY (Continued)
MOPAR
T
LOCK CYLINDER LUBRICANT OR
EQUIVALENT
• Door Lock Cylinders
SPECIAL TOOLS
BODY
INDEX
DESCRIPTION
FIGURE
STICK, TRIM C 4755
16
REMOVER, MOLDINGS C-4829
17
PLIERS, HEADLINER CLIP 6967
18
OUTER BELT MOLDING REMOVER - 9093
19
Fig. 16 STICK, TRIM C 4755
Fig. 17 REMOVER, MOLDINGS C-4829
Fig. 18 PLIERS, HEADLINER CLIP 6967
Fig. 19 OUTER BELT MOLDING REMOVER - 9093
CS
BODY
23 - 13
BODY (Continued)
DOOR - FRONT
TABLE OF CONTENTS
page
page
FRONT DOOR APPLIQUE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . 15
CHECK STRAP
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
. . . . . . . . . . . . . . . . . . . . . . . . . 16
DOOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
. . . . . . . . . . . . . . . . . . . . . . . . . 17
. . . . . . . . . . . . . . . . . . . . . . . . 17
DOOR GLASS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . . 18
DOOR GLASS RUN CHANNEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
. . . . . . . . . . . . . . . . . . . . . . . . . 19
DOOR HEADER BLACK OUT TAPE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
. . . . . . . . . . . . . . . . . . . . . . . . . 19
EXTERIOR HANDLE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
. . . . . . . . . . . . . . . . . . . . . . . . . 21
FRAME CLOSEOUT MOLDING
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . . . . . . . . 22
HINGE
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
. . . . . . . . . . . . . . . . . . . . . . . . . 22
LATCH
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . . 23
. . . . . . . . . . . . . . . . . . . . . . . . 24
LATCH STRIKER
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . . 25
. . . . . . . . . . . . . . . . . . . . . . . . 25
LOCK CYLINDER
. . . . . . . . . . . . . . . . . . . . . . . . . 25
TRIM PANEL
. . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
. . . . . . . . . . . . . . . . . . . . . . . . . 27
WATERSHIELD
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
. . . . . . . . . . . . . . . . . . . . . . . . . 28
WINDOW REGULATOR
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
. . . . . . . . . . . . . . . . . . . . . . . . . 29
GLASS RUN LOWER CHANNEL
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
. . . . . . . . . . . . . . . . . . . . . . . . . 30
23 - 14
DOOR - FRONT
CS
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст