Chrysler Pacifica. Manual — part 224
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Power Mirror connector.
Turn the ignition on.
Measure the voltage of the Driver Mirror Common Driver circuit.
Is the voltage above 1.0 volts?
All
Yes
→ Repair the Driver Mirror Common Driver circuit for a short to
voltage.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Driver Door Module.
Perform BODY VERIFICATION TEST - VER 1.
893
POWER MIRROR
DRIVER MIRROR COMMON OUTPUT SHORT TO BATTERY - DDM —
Continued
Symptom:
DRIVER MIRROR COMMON OUTPUT SHORT TO GROUND - DDM
When Monitored and Set Condition:
DRIVER MIRROR COMMON OUTPUT SHORT TO GROUND - DDM
When Monitored:
Whenever mirror is idle.
Set Condition:
Driver circuit is shorted to ground.
POSSIBLE CAUSES
DTC PRESENT
POWER MIRROR
DRIVER MIRROR COMMON DRIVER SHORTED TO GROUND
DRIVER DOOR MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase DTCs.
Cycle the ignition switch Off then back On.
With the DRBIII
t, read DTCs.
Did the same DTC return?
All
Yes
→ Go To 2
No
→ The conditions required to set the code are currently not present.
Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the power mirror connector.
Turn the ignition on.
Using the DRBIII
t, erase DTC’s.
Cycle the ignition switch Off then back On.
With the DRBIII
t, read DTC’s.
Did the same DTC return?
All
Yes
→ Go To 3
No
→ Inspect the power mirror harness for a short, if OK replace the
mirror.
Perform BODY VERIFICATION TEST - VER 1.
894
POWER MIRROR
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Power Mirror connector.
Turn the ignition on.
Measure the Driver Mirror Common Driver circuit to ground.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Driver Mirror Common Driver circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Driver Door Module.
Perform BODY VERIFICATION TEST - VER 1.
895
POWER MIRROR
DRIVER MIRROR COMMON OUTPUT SHORT TO GROUND - DDM —
Continued
Symptom:
DRIVER MIRROR HORIZONTAL OUTPUT SHORT TO BATTERY -
DDM
When Monitored and Set Condition:
DRIVER MIRROR HORIZONTAL OUTPUT SHORT TO BATTERY - DDM
When Monitored:
Whenever mirror is idle.
Set Condition:
Driver circuit is shorted to battery.
POSSIBLE CAUSES
DTC PRESENT
POWER MIRROR
DRIVER MIRROR HORIZONTAL DRIVER SHORTED TO VOLTAGE
DRIVER DOOR MODULE
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, erase DTCs.
Cycle the ignition switch Off then back On.
With the DRBIII
t, read DTCs.
Did the same DTC return?
All
Yes
→ Go To 2
No
→ The conditions required to set the code are currently not present.
Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the power mirror connector.
Using the DRBIII
t, erase DTC’s.
Turn the ignition on.
Cycle the ignition switch Off then back On.
With the DRBIII
t, read DTC’s.
Did the same DTC return?
All
Yes
→ Go To 3
No
→ Inspect the power mirror harness for a short, if OK replace the
mirror.
Perform BODY VERIFICATION TEST - VER 1.
896
POWER MIRROR
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст