Chrysler Pacifica. Manual — part 846
REAR DOOR OUTER BELT
MOLDING
REMOVAL
(1) Lower window completely.
(2) Remove
rear
inner
molding
weatherstrip.
(Refer to 23 - BODY/WEATHERSTRIP/SEALS/REAR
DOOR INNER BELT MOLDING - REMOVAL).
(3) Remove fixed glass run channel. (Refer to 23 -
BODY/DOORS - REAR/REAR DOOR FIXED GLASS
RUN CHANNEL - REMOVAL).
(4) Remove fixed glass run channel.
(5) Remove screws attaching outer belt molding,
one at the inside of the rear door shut face at the
B-pillar and one at the inside of the rear door shut
face at the C-pillar.
(6) Insert special tool #9093 between belt molding
and glass at rear and then slide tool forward approx-
imately 14 cm (5.5 in.) (Fig. 13) and (Fig. 14).
(7) Push down on outer belt molding and rotate
upper part of tool outward from vehicle approxi-
mately 6 - 8 cm (2.5 - 3 in.) then lift up on molding to
disengage from locking tab.
(8) Repeat step 3 and 4 at as necessary till outer
belt molding is free.
(9) Remove outer belt molding weatherstrip.
INSTALLATION
(1) Place outer belt molding weatherstrip into posi-
tion (Fig. 13).
(2) Press down or tap lightly on outer belt molding
until fully seated.
(3) Install screws attaching outer belt molding, one
at the inside of the rear door shut face at the B-pillar
and one at the inside of the rear door shut face at
the C-pillar.
(4) Install fixed glass run channel.
(5) Install rear inner molding weatherstrip. (Refer
to 23 - BODY/WEATHERSTRIP/SEALS/REAR DOOR
INNER BELT MOLDING - INSTALLATION).
(6) Install door trim panel. (Refer to 23 - BODY/
DOORS - REAR/TRIM PANEL - INSTALLATION).
(7) Close window.
Fig. 13 DOOR OUTER BELT MOUNTING
1 - OUTER BELT MOLDING
2 - DOOR ASSEMBLY
Fig. 14 OUTER BELT MOLDING
1 - OUTER BELT MOLDING
2 - SPECIAL TOOL #9093
3 - RETAINING TAB
4 - DOOR OUTER PANEL
CS
WEATHERSTRIP/SEALS
23 - 179
REAR DOOR OPENING
WEATHERSTRIP
REMOVAL
(1) Open front door.
(2) Remove rear door sill scuff plate.
(3) Pull rear door weatherstrip from door opening
fence (Fig. 15).
(4) Remove door opening weatherstrip from vehi-
cle.
INSTALLATION
(1) Place rear door opening weatherstrip into posi-
tion starting at the upper rear corner of the C-pillar
(Fig. 4).
(2) Work the weatherstrip down the C-pillar to the
floor pan. Leave slack to ensure completion of the
weatherstrip throughout the entire opening.
(3) Starting at B-pillar going along the under side
of the header and down the B-pillar leaving slack to
ensure proper installation of the bottom portion of
the weatherstrip.
(4) Joint the two end of the weatherstrip together
and ensure complete seating of weatherstrip.
(5) Install rear door sill scuff plate.
(6) Close front door.
Fig. 15 REAR DOOR OPENING WEATHERSTRIP
1 - C-PILLAR STARTING POINT
2 - B-PILLAR CORNER
3 - REAR DOOR OPENING WEATHERSTRIP
23 - 180
WEATHERSTRIP/SEALS
CS
BODY STRUCTURE
TABLE OF CONTENTS
page
page
GAP AND FLUSH
SPECIFICATIONS - GAP AND FLUSH
. . . . . . . . . . . . . . . . . . . . 181
OPENING DIMENSIONS
. . . . . . . . . . . . . . . . . . . . . . . . 184
SEALER LOCATIONS
. . . . . . . . . . . . . . . . . . . . . . . . . 188
STRUCTURAL ADHESIVE LOCATIONS
SPECIFICATIONS - STRUCTURAL ADHESIVE
. . . . . . . . . . . . . . . . . . . . . . . . . 192
WELD LOCATIONS
SPECIFICATIONS - WELD LOCATION
GAP AND FLUSH
SPECIFICATIONS - GAP AND FLUSH
MEASUREMENTS
INDEX
DESCRIPTION
FIGURE
GAP & FLUSH MEASUREMENTS
1
CS
BODY STRUCTURE
23 - 181
Fig. 1 GAP AND FLASH MEASUREMENTS
23 - 182
BODY STRUCTURE
CS
GAP AND FLUSH (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст