Chrysler Pacifica. Manual — part 180
Symptom:
FUEL SENSOR 2 SHORT - BCM
When Monitored and Set Condition:
FUEL SENSOR 2 SHORT - BCM
When Monitored:
When the BCM is powered up.
Set Condition:
This DTC will set when the BCM detects the Fuel Level Sensor 2 circuit
resistance is less than 25 ohms for 10 seconds.
POSSIBLE CAUSES
FUEL LEVEL SENSOR
FUEL LEVEL SENSE 2 CIRCUIT SHORT TO GROUND
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition off.
Disconnect the Fuel Pump Module harness connector.
Turn the ignition on, with the DRBIII
t, read DTCs.
Does the DRBIII
t display 9Fuel Sensor 2 Open9?
All
Yes
→ Replace the Fuel Level Sensor in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition off.
Disconnect the Fuel Pump Module harness connector.
Disconnect the BCM harness connector.
Measure the resistance between ground and the Fuel Level Sense 2 circuit.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Fuel Level Sense 2 circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace and program the BCM in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
717
INSTRUMENT CLUSTER
Symptom:
INCORRECT ODOMETER VALUE
When Monitored and Set Condition:
INCORRECT ODOMETER VALUE
When Monitored:
During power up.
Set Condition:
If the Instrument Cluster detects the odometer value memory is corrupted
or does not match the previously stored odometer value, this code will set. When this code
is set the VF odometer will diplay [ - - ].
POSSIBLE CAUSES
INSTRUMENT CLUSTER
TEST
ACTION
APPLICABILITY
1
CAUTION: Do not attempt to exchange or
(swap( an Instrument Cluster or
a BCM from one vehicle to another. Module memory/configuration damage
may occur. Refer to the Instrument Cluster Service Information.
Ensure that the Instrument Cluster has not been damaged or previously installed in
a different vehicle.
With the DRBIII
t, erase DTCs.
Turn the ignition off, wait 10 seconds, then turn the ignition on.
With the DRBIII
t, read DTCs.
When this code is set, the Instrument Cluster must be replaced.
All
View Repair
Replace the Instrument Cluster in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
718
INSTRUMENT CLUSTER
Symptom:
LEFT TURN SIGNAL INDICATOR OPEN - BCM
When Monitored and Set Condition:
LEFT TURN SIGNAL INDICATOR OPEN - BCM
When Monitored:
Output is Off.
Set Condition:
Feedback Sense is Low for 125 msec. (No circuit load.)
POSSIBLE CAUSES
INSTRUMENT CLUSTER
LEFT TURN SIGNAL CIRCUIT OPEN
BCM
TEST
ACTION
APPLICABILITY
1
Turn the ignition off.
Disconnect the BCM C4 harness connector.
Turn the ignition on.
Measure the voltage between the Left Turn Signal circuit and ground.
Is the voltage below 5 volts?
All
Yes
→ Replace the Instrument Cluster in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition off.
Disconnect the BCM C4 harness connector.
Disconnect the Instrument Cluster harness connector.
Measure the resistance of the Left Turn Signal circuit.
Is the resistance above 5.0 ohms?
All
Yes
→ Repair the Left Turn Signal circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the BCM in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
719
INSTRUMENT CLUSTER
Symptom:
LEFT TURN SIGNAL INDICATOR SHORT - BCM
When Monitored and Set Condition:
LEFT TURN SIGNAL INDICATOR SHORT - BCM
When Monitored:
Output is On.
Set Condition:
Feedback Sense is High for 125 msec. (Excessive circuit load.)
POSSIBLE CAUSES
BCM
LEFT TURN SIGNAL CIRCUIT SHORT TO GROUND
INSTRUMENT CLUSTER
TEST
ACTION
APPLICABILITY
1
Turn the ignition off.
Disconnect the BCM C4 harness connector.
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Does the LEFT TURN SIGNAL INDICATOR SHORT reset?
All
Yes
→ Replace the BCM in accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition off.
Disconnect the BCM C4 harness connector.
Disconnect the Instrument Cluster C1 harness connector.
Measure the resistance between ground and the Left Turn Signal circuit.
Is the resistance below 5.0 ohms?
All
Yes
→ Repair the Left Turn Signal circuit for a short to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Instrument Cluster in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
720
INSTRUMENT CLUSTER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст