Chrysler Pacifica. Manual — part 118
Symptom:
LEFT FRONT SIDE MARKER LAMP OPEN-IPM
When Monitored and Set Condition:
LEFT FRONT SIDE MARKER LAMP OPEN-IPM
When Monitored:
Output is OFF.
Set Condition:
The IPM detects an open fault condition. Time to set is 1 second.
POSSIBLE CAUSES
GROUND CIRCUIT OPEN
INTEGRATED POWER MODULE
LEFT FRONT SIDE MARKER LAMP
LEFT FRONT SIDE MARKER LAMP DRIVER OPEN
WIRING HARNESS INSPECTION
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, erase the IPM DTC’s.
Turn the Side Marker Lamps on.
With the DRB, read the IPM DTC’s.
Does the DRBIII
t read: Left Front Side Marker Lamp Open?
All
Yes
→ Go To 2
No
→ Go To 5
2
Turn the ignition off.
Disconnect the Left Front Side Marker Lamp harness connector.
Using a 12-volt test light connected to 12-volts, check the Ground circuit.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Does the test light illuminate brightly?
All
Yes
→ Go To 3
No
→ Repair the Ground circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition off.
Disconnect the Left Front Side Marker Lamp.
Disconnect the IPM C5 harness connector.
Measure the resistance of the Left Front Side Marker Lamp Driver circuit.
Is the resistance below 10.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the Left Front Side Marker Lamp Driver circuit for an
open.
Perform BODY VERIFICATION TEST - VER 1.
469
EXTERIOR LIGHTING
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Disconnect the Left Front Side Marker Lamp harness connector.
Using a 12-volt test light connected to ground, check the Left Front Side Marker
Lamp Driver circuit in the Left Front Side Marker Lamp harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Turn the Side Marker Lamps on.
Does the test light illuminate brightly?
All
Yes
→ Replace the Left Front Side Marker Lamp Bulb.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Integrated Power Module.
Perform BODY VERIFICATION TEST - VER 1.
5
Turn the ignition off.
NOTE: Visually inspect the related wiring harness and circuits. Look for
any chafed, pierced, pinched, or partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
NOTE: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
470
EXTERIOR LIGHTING
LEFT FRONT SIDE MARKER LAMP OPEN-IPM —
Continued
Symptom:
LEFT FRONT SIDE MARKER LAMP SHORT TO GROUND-IPM
When Monitored and Set Condition:
LEFT FRONT SIDE MARKER LAMP SHORT TO GROUND-IPM
When Monitored:
Output is ON.
Set Condition:
The IPM detects a short fault condition. Time to set is 1 second.
POSSIBLE CAUSES
INTEGRATED POWER MODULE
LEFT FRONT SIDE MARKER LAMP
LEFT FRONT SIDE MARKER LAMP DRIVER SHORT TO GROUND
WIRING PROBLEM
WIRING HARNESS INSPECTION
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, clear the IPM DTC’s.
Turn the Side Marker Lamps on.
With the DRBIII
t, read IPM DTC’s.
Is this DTC present?
All
Yes
→ Go To 3
No
→ Go To 2
2
Turn the ignition off.
NOTE: Visually inspect the related wiring harness and circuits. Look for
any chafed, pierced, pinched, or partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
NOTE: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Turn the ignition off.
Disconnect the Left Front Side Marker Lamp.
Disconnect the Intelligent Power Module C5 harness connector.
Measure the resistance between Ground and the Left Front Side Marker Lamp
Driver circuit.
Is the resistance below 100.0 ohms?
All
Yes
→ Repair the Left Front Side Marker Lamp Driver circuit for a short
to ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
471
EXTERIOR LIGHTING
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Turn the Side Marker Lamps off.
Install a substitute Side Marker Lamp Bulb in place of the Left Front Side Marker
Lamp Bulb.
Turn the ignition on.
With the DRBIII
t, erase the IPM DTC’s.
Turn the Side Marker Lamps on.
With the DRBIII
t, read IPM DTC’s.
Does the DRBIII
t display this DTC?
All
Yes
→ Go To 5
No
→ Replace the original Left Side Marker Park Lamp Bulb.
Perform BODY VERIFICATION TEST - VER 1.
5
Turn the ignition off.
Inspect the wiring and connectors associated with the Left Front Side Marker Lamp
Driver circuit.
Were any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Integrated Power Module.
Perform BODY VERIFICATION TEST - VER 1.
472
EXTERIOR LIGHTING
LEFT FRONT SIDE MARKER LAMP SHORT TO GROUND-IPM —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст