Chrysler Pacifica. Manual — part 108
Symptom:
DRIVER HEATED SEAT SWITCH SHORT - DDM
When Monitored and Set Condition:
DRIVER HEATED SEAT SWITCH SHORT - DDM
When Monitored:
Continuously.
Set Condition:
If the MUX circuit is under 0.10 volt for over 10 seconds, this code will set.
POSSIBLE CAUSES
DTC PRESENT
POWER SEAT SWITCH
DRIVER HEATED SEAT SWITCH MUX SHORT TO GROUND
DRIVER DOOR MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Cycle the ignition switch from Off to Run.
Operate the suspect switch in both positions several times.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display DRIVER HEATED SEAT SWITCH SHORT?
All
Yes
→ Go To 2
No
→ The condition that caused this code to set is not present at this
time.
Perform BODY VERIFICATION TEST - VER 1.
2
Disconnect the Driver Power Seat Switch connector.
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Cycle the ignition switch from Off to Run and wait 10 seconds.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display DRIVER HEATED SEAT SWITCH SHORT?
All
Yes
→ Go To 3
No
→ Replace the Power Seat Switch.
Perform BODY VERIFICATION TEST - VER 1.
429
ELECTRICALLY HEATED SYSTEMS
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Driver Power Seat Switch connector.
Disconnect the Driver Door Module C2 connector.
Inspect the Driver Heated Seat Switch MUX circuit for a short to ground or to
another circuit in the seat switch harness.
Were there any problems found?
All
Yes
→ Repair the Driver Heated Seat Switch MUX circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Driver Door Module.
Perform BODY VERIFICATION TEST - VER 1.
430
ELECTRICALLY HEATED SYSTEMS
DRIVER HEATED SEAT SWITCH SHORT - DDM —
Continued
Symptom:
DRIVER HEATED SEAT SWITCH STUCK - DDM
When Monitored and Set Condition:
DRIVER HEATED SEAT SWITCH STUCK - DDM
When Monitored:
Continuously.
Set Condition:
If the switch is held in the on position for over 10 seconds, this code will
set.
POSSIBLE CAUSES
DTC PRESENT
DRIVER POWER SEAT SWITCH
DRIVER HEATED SEAT SW MUX
DRIVER DOOR MODULE
TEST
ACTION
APPLICABILITY
1
Check the heated seat switch mechanical operation for a sticking condition. Correct
as necessary.
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Cycle the ignition switch from Off to Run.
Operate the Heated Seat Switch several times.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display DRIVER HEATED SEAT SWITCH STUCK?
All
Yes
→ Go To 2
No
→ The condition that caused this code to set is not present at this
time. Operate the switch several times to ensure it does not stick.
If the switch ever sticks, replace it.
Perform BODY VERIFICATION TEST - VER 1.
2
Disconnect the Driver Power Seat Switch connector.
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Cycle the ignition switch from Off to Run and wait 30 seconds.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display DRIVER HEATED SEAT SWITCH STUCK?
All
Yes
→ Go To 3
No
→ Replace the Driver Power Seat Switch.
Perform BODY VERIFICATION TEST - VER 1.
431
ELECTRICALLY HEATED SYSTEMS
TEST
ACTION
APPLICABILITY
3
Turn the ignition off.
Disconnect the Driver Power Seat Switch connector.
Disconnect the Driver Door Module C2 connector.
Inspect the Driver Heated Seat Switch MUX circuit for a partial short to ground or
to another circuit in the seat switch harness.
Were there any problems found?
All
Yes
→ Repair the Driver Heated Seat Switch MUX circuit as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Driver Door Module.
Perform BODY VERIFICATION TEST - VER 1.
432
ELECTRICALLY HEATED SYSTEMS
DRIVER HEATED SEAT SWITCH STUCK - DDM —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст