Chrysler Pacifica. Manual — part 539
(4) Install clip attaching cable to servo (Fig. 5).
(5) Install two nuts attaching mounting bracket
and speed control cable to servo (Fig. 6).
(6) Tighten nuts to 6.8 N·m (60 in. lbs.).
(7) Connect electrical connectors and vacuum hose.
(8) Install speed control cable to throttle cam by
sliding clasp into hole (Fig. 1).
(9) Install the servo bracket bolt.
(10) Tighten bolt to 5.6 N·m (50 in. lbs.).
(11) Connect negative battery cable.
SERVO
REMOVAL
(1) Disconnect the negative battery cable.
(2) Remove the servo bracket bolt.
(3) Remove speed control cable from throttle cam
by sliding clasp out hole used for throttle cable (Fig.
7).
(4) Disconnect electrical connectors and vacuum
hose.
(5) Remove two nuts attaching mounting bracket
and speed control cable to servo (Fig. 8).
Fig. 5 CABLE CLIP
Fig. 6 CABLE TO SERVO MOUNTING
Fig. 7 CABLE ROUTING
Fig. 8 CABLE TO SERVO MOUNTING
CS
SPEED CONTROL
8P - 3
CABLE (Continued)
(6) Pull cable away from servo to expose retaining
clip and remove clip attaching cable to servo (Fig. 9).
(7) Remove the servo.
INSTALLATION
(1) Install clip attaching cable to servo (Fig. 10).
(2) Install two nuts attaching mounting bracket
and speed control cable to servo (Fig. 11).
(3) Tighten nuts to 6.8 N·m (60 in. lbs.).
(4) Connect electrical connectors and vacuum hose
(Fig. 12).
Fig. 9 CABLE CLIP
Fig. 10 CABLE CLIP
Fig. 11 CABLE TO SERVO MOUNTING
Fig. 12 VACUUM HOSE
8P - 4
SPEED CONTROL
CS
SERVO (Continued)
(5) Install the servo bracket bolt (Fig. 13)
(6) Tighten bolt to 5.6 N·m (50 in. lbs.).
(7) Connect the negative battery cable.
SWITCH
REMOVAL
(1) Disconnect the negative battery cable.
(2) Remove the Driver side Airbag (Fig. 14), (Refer
to 8 - ELECTRICAL/RESTRAINTS/DRIVER AIRBAG
- REMOVAL).
(3) Remove the speed control switch mounting
screw (Fig. 15).
(4) Disconnect the electrical connector from switch.
(5) Remove switch.
Fig. 13 SERVO & BRACKET
STEERING WHEEL & SWITCHES
Fig. 14 AIRBAG REMOVED
Fig. 15 SWITCH MOUNTING SCREW
CS
SPEED CONTROL
8P - 5
SERVO (Continued)
INSTALLATION
(1) Connect the electrical connector to switch.
(2) Install switch.
(3) Install the speed control switch mounting
screw (Fig. 16).
(4) Tighten Screw.
(5) Install the Driver side Airbag (Fig. 17), (Refer
to 8 - ELECTRICAL/RESTRAINTS/DRIVER AIRBAG
- INSTALLATION).
(6) Connect the negative battery cable (Fig. 18).
VACUUM RESERVOIR
REMOVAL
(1) Disconnect the negative and then the positive
battery cable.
(2) Remove battery.
(3) Disconnect the wiring harness from battery
tray (Fig. 19).
Fig. 16 SWITCH MOUNTING SCREW
Fig. 17 AIRBAG REMOVED
Fig. 18 STEERING WHEEL & SWITCHES
Fig. 19 BATTERY TRAY/ VACUUM RESERVOIR
8P - 6
SPEED CONTROL
CS
SWITCH (Continued)
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст