Chrysler Pacifica. Manual — part 122
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Disconnect the Left Rear Park Lamp harness connector.
Using a 12-volt test light connected to ground, check the Left Tail Lamp Driver
circuit in the Left Rear Park Lamp harness connector.
NOTE: The test light must illuminate brightly. Compare the brightness to
that of a direct connection to the battery.
Turn the Park Lamps on.
Does the test light illuminate brightly?
All
Yes
→ Replace the Left Rear Park Lamp Bulb.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Integrated Power Module.
Perform BODY VERIFICATION TEST - VER 1.
5
Turn the ignition off.
NOTE: Visually inspect the related wiring harness and circuits. Look for
any chafed, pierced, pinched, or partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
NOTE: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
485
EXTERIOR LIGHTING
LEFT REAR PARK/MARKER LAMP OPEN-IPM —
Continued
Symptom:
LEFT REAR PARK/MARKER LAMP SHORT TO GROUND-IPM
When Monitored and Set Condition:
LEFT REAR PARK/MARKER LAMP SHORT TO GROUND-IPM
When Monitored:
The output is ON.
Set Condition:
The IPM detects a short fault condition. Time to set is 1 second.
POSSIBLE CAUSES
INTEGRATED POWER MODULE
LEFT REAR PARK/MARKER LAMPS
LEFT TAIL LAMP DRIVER SHORT TO GROUND
WIRING PROBLEM
WIRING HARNESS INSPECTION
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, clear the IPM DTC’s.
Turn the Park Lamps on.
With the DRBIII
t, read IPM DTC’s.
Is this DTC present?
All
Yes
→ Go To 3
No
→ Go To 2
2
Turn the ignition off.
NOTE: Visually inspect the related wiring harness and circuits. Look for
any chafed, pierced, pinched, or partially broken wires.
NOTE: Visually inspect the related wiring harness connectors. Look for
broken, bent, pushed out, or corroded terminals.
NOTE: Refer to any Technical Service Bulletins (TSB) that may apply.
Were any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Turn the ignition off.
Disconnect the Left Rear Park/Marker Lamp.
Disconnect the Intelligent Power Module C9 harness connector.
Measure the resistance between Ground and the Left Tail Lamp Driver circuit.
Is the resistance below 100.0 ohms?
All
Yes
→ Repair the Left Rear Tail Lamp Driver circuit for a short to
ground.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
486
EXTERIOR LIGHTING
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Turn the Park Lamps off.
Install substitute Park/Marker Lamp Bulbs in place of the Left Rear Park/Marker
Lamp Bulbs.
Turn the ignition on.
With the DRBIII
t, erase the IPM DTC’s.
Turn the Park Lamps on.
With the DRBIII
t, read IPM DTC’s.
Does the DRBIII
t display this DTC?
All
Yes
→ Go To 5
No
→ Replace the original Left Rear Park/Marker Lamp Bulbs.
Perform BODY VERIFICATION TEST - VER 1.
5
Turn the ignition off.
Inspect the wiring and connectors associated with the Left Tail Lamp Driver circuit.
Were any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Integrated Power Module.
Perform BODY VERIFICATION TEST - VER 1.
487
EXTERIOR LIGHTING
LEFT REAR PARK/MARKER LAMP SHORT TO GROUND-IPM —
Continued
Symptom:
LEFT REAR TURN SIGNAL OUTPUT OPEN-BCM
POSSIBLE CAUSES
INTERMITTENT CONDITION
GROUND CIRCUIT OPEN
TURN SIGNAL LAMP OPEN
LEFT REAR TURN SIGNAL LAMP DRIVER CIRCUIT OPEN
BODY CONTROL MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, clear all BCM DTC’s.
Actuate the Turn Signals.
With the DRBIII
t, read the DTC information.
Does the DRBIII
t read: Left Rear Turn Signal Output Open?
All
Yes
→ Go To 2
No
→ The condition that caused the symptom is currently not present.
Inspect the related wiring for a possible intermittent condition.
Look for any chafed, pierced,pinched, or partially broken wires.
Perform BODY VERIFICATION TEST - VER 1.
2
Turn the ignition off.
Disconnect the Left Rear Turn Signal harness connector.
Using a 12-volt test light connected to 12-volts, check the ground circuit.
Does the test light illuminate brightly?
All
Yes
→ Go To 3
No
→ Repair the Ground Circuit.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition off.
Disconnect the Left Rear Turn Signal Lamp connector.
Turn the ignition on.
Turn the Left Turn Signal on.
Using a 12-volt test light connected to ground, check the Left Rear Turn Signal
Output circuit.
Does the test light illuminate brightly?
All
Yes
→ Replace the Turn Signal Lamp.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
488
EXTERIOR LIGHTING
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст