Chrysler Pacifica. Manual — part 203
TEST
ACTION
APPLICABILITY
5
With the DRBIII
t select THEFT ALARM, SKIM, MONITORS, RKE MONITOR and
observe the
9FOB #9 and 9FOB Button9..
Press the LOCK button and then the UNLOCK button on the Transmitter.
Does the DRBIII
t display:9 UNLOCK9, 9LOCK9 and the 9FOB Number9?
All
Yes
→ Go To 6
No
→ Go To 7
6
With the DRBIII
t select THEFT ALARM, SKIM, MONITORS, RKE MESSAGE
FROM BCM and observe the
9FOB #9 and 9FOB Button9..
Press the LOCK button and then the UNLOCK button on the Transmitter.
Does the DRBIII
t display:9 UNLOCK9, 9LOCK9 and the 9FOB Number9?
All
Yes
→ Replace the Driver Door Module in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Body Control Module in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
7
With the DRBIII
t select THEFT ALARM, SKIM, then PROGRAM NEW KEY. Follow
instructions on the screen.
Exit PROGRAM NEW KEY. Try the Door Locks using the Transmitter.
Did the Door Locks respond properly to the Transmitter commands ?
All
Yes
→ Repair complete. Using the DRBIII, program other Transmitters
used with this Vehicle.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 8
8
Secure a known good Transmitter.
Using the DRBIII
t select THEFT ALARM, SKIM then PROGRAM NEW KEY and
follow the instructions on the DRBIII
t screen.
Exit PROGRAM new key. Try the Door Locks using the Transmitter.
Did the Door Locks respond properly to the Transmitter commands ?
All
Yes
→ Replace the Transmitter. Program all Transmitters that will be
used with this Vehicle.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Sentry Key RemotE Entry Module.
Perform BODY VERIFICATION TEST - VER 1.
Note: When repairs are complete ensure all transmitters used with this
vehicle are programmed
9
Using the 9001 RF Detector, follow the instructions on the back of the tester and test
the transmitter several times.
Does the signal strength measure
9STRONG9?
All
Yes
→ Go To 10
No
→ Check and replace the batteries if they are under 3.0 volts each
and retest the transmitter. If the batteries are okay, replace the
transmitter.
Perform BODY VERIFICATION TEST - VER 1.
809
POWER DOOR LOCKS/RKE
*REMOTE KEYLESS ENTRY INOPERATIVE —
Continued
TEST
ACTION
APPLICABILITY
10
With the DRBIII
t, select THEFT ALARM, SKIM then PROGRAM NEW KEY and
follow the instructions on the screen.
Exit PROGRAM NEW KEY.
Activate the Door Locks using the RKE Transmitter.
Did the door locks respond properly to the RKE transmitter commands?
All
Yes
→ Repair complete.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Sentry Key RemotE Entry Module.
Perform BODY VERIFICATION TEST - VER 1.
810
POWER DOOR LOCKS/RKE
*REMOTE KEYLESS ENTRY INOPERATIVE —
Continued
Symptom:
AMBIENT TEMPERATURE SENSOR CIRCUIT OPEN
When Monitored and Set Condition:
AMBIENT TEMPERATURE SENSOR CIRCUIT OPEN
When Monitored:
Whenever the Power Liftgate Module is awake.
Set Condition:
If the module senses a resistance above 382K ohms on the Liftgate
Temperature Sensor Signal circuit, this code will set. The normal range for the sensor is
1.2K to 382K ohms. At room temperature (68° F) the resistance will be between 11.2 K and
13.5K ohms.
POSSIBLE CAUSES
DTC PRESENT
POWER LIFTGATE MODULE - TEMPERATURE SENSE OPEN
LIFTGATE TEMPERATURE SENSOR SIGNAL WIRE OPEN
GROUND WIRE OPEN
LIFTGATE TEMPERATURE SENSOR
TEST
ACTION
APPLICABILITY
1
With the DRBIII
t, record and erase DTC’s.
Turn the ignition off, wait 10 seconds, then turn the ignition on.
Operate the liftgate several times.
With the DRBIII
t, read DTCs.
Does the DRBIII
t display AMBIENT TEMPERATURE SENSOR CIRCUIT OPEN?
All
Yes
→ Go To 2
No
→ Using the wiring diagram/schematic as a guide, inspect the
wiring and connectors for an intermittent condition.
Perform BODY VERIFICATION TEST - VER 1.
2
Remove the power liftgate motor trim panel.
Disconnect the Power Liftgate Module C2 connector.
Measure the resistance of the liftgate Temperature Sensor Signal circuit to the
Ground circuit (cavity 20) in the PLG C2 connector.
Is the resistance between 1.2k and 382K ohms?
All
Yes
→ Replace the Power Liftgate Module.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
811
POWER DOORS - LIFTGATE
TEST
ACTION
APPLICABILITY
3
Remove the power liftgate motor trim panel.
Disconnect the Power Liftgate Module C2 connector.
Disconnect the License Lamp (light bar) connector.
Measure the resistance of the liftgate Temperature Sensor Signal circuit between the
License Lamp connector and the PLG C2 connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Go To 4
No
→ Repair the Liftgate Temperature Sensor Signal circuit for an
open.
Perform BODY VERIFICATION TEST - VER 1.
4
Remove the power liftgate motor trim panel.
Disconnect the Power Liftgate Module C2 connector.
Disconnect the License Lamp (light bar) connector.
Measure the resistance of the Ground circuit between the PLG C2 connector (cavity
20) and the License Lamp connector (cavity 8).
Is the resistance below 5.0 ohms
All
Yes
→ Go To 5
No
→ Repair the Liftgate Temperature Sensor Ground wire for an open.
Perform BODY VERIFICATION TEST - VER 1.
5
If there are no possible causes remaining, view repair.
All
Repair
Replace the Liftgate Temperature Sensor (light bar).
Perform BODY VERIFICATION TEST - VER 1.
812
POWER DOORS - LIFTGATE
AMBIENT TEMPERATURE SENSOR CIRCUIT OPEN —
Continued
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст