Chrysler Pacifica. Manual — part 272
Symptom:
FRONT WIPER ON/OFF RELAY SHORT TO BATTERY-IPM
POSSIBLE CAUSES
WIPER ON/OFF RELAY CONTROL CIRCUIT SHORTED TO BATTERY
WIPER ON/OFF RELAY
INTEGRATED POWER MODULE
TEST
ACTION
APPLICABILITY
1
Turn the ignition off.
Remove the Wiper On/Off Relay from the IPM.
Disconnect the IPM C8 harness connector.
Turn the ignition on.
Measure the voltage of the Wiper On/Off Relay Control circuit at the IPM connector.
Is the voltage above 1.0 volt?
All
Yes
→ Repair the Wiper On/Off Relay Control circuit for a short to
battery.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Install a substitute relay in place of the Wiper On/Off Relay.
Turn the ignition on.
Turn the wipers on.
Does the system operate correctly?
All
Yes
→ Replace the Wiper On/Off Relay.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Integrated Power Module.
Perform BODY VERIFICATION TEST - VER 1.
1085
WINDSHIELD WIPER & WASHER
Symptom:
FRONT WIPER PARK SWITCH OPEN-IPM
POSSIBLE CAUSES
FRONT WIPER ON/OFF RELAY
FRONT WIPER PARK SWITCH
FRONT WIPER PARK SWITCH SENSE CIRCUIT OPEN
FRONT WIPER FUSED B(+) CIRCUIT OPEN
FRONT WIPER PARK SWITCH GROUND CIRCUIT OPEN
INTEGRATED POWER MODULE
INTERMITTENT WIRING AND CONNECTORS
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Operate the Wiper system in all modes.
With the DRBIII
t, read DTCs.
Does the DTC reset?
All
Yes
→ Go To 2
No
→ Go To 8
2
Turn the ignition on..
With the DRBIII
t, erase DTCs.
Install a substitute relay in place of the Front Wiper On/Off Relay.
Operate the Wiper system in all modes.
With the DRBIII
t, read DTCs.
Does the DTC reset?
All
Yes
→ Go To 3
No
→ Replace the Front Wiper On/Off Relay in accordance with the
Service Information.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Turn the ignition off.
NOTE: Place the Wipers in the
(parked( position.
Disconnect the Front Wiper Motor harness connector
Measure the resistance of the Park Switch between the Front Wiper Motor Ground
circuit and the Front Wiper Park Switch Sense circuit in the Front Wiper Motor
connector.
Is the resistance above 5.0 ohms?
All
Yes
→ Replace the Front Wiper Motor in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
1086
WINDSHIELD WIPER & WASHER
TEST
ACTION
APPLICABILITY
4
Turn the ignition off.
Disconnect the Front Wiper Motor.
Disconnect the IPM C7 harness connector.
Measure the resistance of the Front Wiper Park Switch Sense circuit between the
IPM harness connector and the Front Wiper Motor harness connector.
Is the resistance above 5.0 ohms?
All
Yes
→ Repair the Front Wiper Park Switch Sense Circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 5
5
Turn the ignition off.
Disconnect the Front Wiper On/Off Relay.
Disconnect the IPM C7 harness connector.
Measure the resistance of the Front Wiper Park Switch Sense circuit between the
IPM harness connector and the Front Wiper On/Off Relay connector.
Is the resistance above 5.0 ohms?
All
Yes
→ Repair the Front Wiper Fused B(+) circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 6
6
Turn the ignition off.
Disconnect the Front Wiper Motor.
Measure the resistance between the Front Wiper Park Switch Ground circuit at the
Front Wiper Motor harness connector.
Is the resistance above 5.0 ohms?
All
Yes
→ Repair the Front Wiper Park Switch Ground Circuit for an open.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 7
7
Turn the ignition off.
Disconnect the Front Wiper Motor.
Disconnect the IPM C7 harness connector.
Turn the ignition on.
Measure the resistance of the Front Wiper Park Switch Sense circuit between the
Front Wiper Motor and the IPM harness connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Test Complete.
No
→ Replace the Integrated Power Module in accordance with the
Service Information.
Perform BODY VERIFICATION TEST - VER 1.
8
The conditions necessary to set this DTC are not present at this time.
Using the schematics as a guide, inspect the wiring and connectors specific to this
circuit.
Wiggle the wiring while checking for shorts and open circuits.
Were there any problems found?
All
Yes
→ Repair as necessary.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Test Complete.
1087
WINDSHIELD WIPER & WASHER
FRONT WIPER PARK SWITCH OPEN-IPM —
Continued
Symptom:
FRONT WIPER PARK SWITCH SHORT TO GROUND-IPM
POSSIBLE CAUSES
FRONT WIPER ON/OFF RELAY
FRONT WIPER PARK SWITCH
FRONT WIPER PARK SWITCH SENSE CIRCUIT SHORT TO GROUND
INTEGRATED POWER MODULE
INTERMITTENT WIRING AND CONNECTORS
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, clear all IPM DTCs.
Operate the Wiper system in all modes.
With the DRBIII
t, read DTCs.
Does the DTC reset?
All
Yes
→ Go To 2
No
→ Go To 5
2
Turn the ignition on..
With the DRBIII
t, erase DTCs.
Turn the ignition off.
Install a substitute relay in place of the On/Off Wiper Relay.
Turn the ignition on.
Operate the Front Wiper system in all modes.
With the DRBIII
t, read DTCs.
Does the DTC reset?
All
Yes
→ Go To 3
No
→ Replace the Front Wiper On/Off Relay in accordance with the
Service Information.
Perform BODY VERIFICATION TEST - VER 1.
3
Turn the ignition on.
With the DRBIII
t, erase DTCs.
Turn the ignition off.
NOTE: Place the Wipers in the
(Parked( position.
Disconnect the Front Wiper Motor harness connector.
Measure the resistance of the Park Switch between the Front Wiper Motor ground
circuit and the Rear Wiper Park Switch Sense circuit in the Front Wiper Motor
connector.
Is the resistance below 5.0 ohms?
All
Yes
→ Replace the Front Wiper Motor in accordance with the Service
Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 4
1088
WINDSHIELD WIPER & WASHER
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст