Chrysler Pacifica. Manual — part 151
Symptom:
PAS FRONT DOOR MESSAGE MISSING (ACTIVE) - ATC
When Monitored and Set Condition:
PAS FRONT DOOR MESSAGE MISSING (ACTIVE) - ATC
When Monitored:
With the ignition on and the IOD fuse installed.
Set Condition:
This DTC will set if the Automatic Temperature Control (ATC) does not
receive the Right Front Door Ajar message from the Passenger Door Module (PDM) for
more than 5 seconds.
POSSIBLE CAUSES
NO COMMUNICATION WITH PASSENGER DOOR MODULE (PDM)
PASSENGER DOOR MODULE (PDM) DTC(S) PRESENT
AUTOMATIC TEMPERATURE CONTROL (ATC)
PASSENGER DOOR MODULE (PDM)
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, read the active ATC DTCs.
Does the DRBIII
t display: NO COMMUNICATION WITH PDM?
All
Yes
→ Return to the Heating & A/C symptom list and choose the
symptom.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition on.
With the DRBIII
t, read PDM DTCs.
Does the DRBIII
t display any DTCs?
All
Yes
→ Refer to the appropriate category for the related symptom(s).
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 3
3
Turn the ignition on.
With DRBIII
t in ATC, Monitor Display, PCI Bus Messages, look for the following
message:
9RT FR DOOR AJAR SW:9
Is
9NO RESPONSE9 displayed after this message?
All
Yes
→ Replace the Passenger Door Module (PDM) in accordance with
the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Replace the Automatic Temperature Control (ATC) in accordance
with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
601
HEATING & A/C
Symptom:
PASSENGER BLEND DOOR TRAVEL TOO SMALL (ACTIVE) - ATC
When Monitored and Set Condition:
PASSENGER BLEND DOOR TRAVEL TOO SMALL (ACTIVE) - ATC
When Monitored:
With the ignition on and the IOD fuse installed.
Set Condition:
The Automatic Temperature Control (ATC) monitors the door’s range of
travel during system initialization. If the measured range is less than expected, the DTC
will set.
POSSIBLE CAUSES
PASSENGER BLEND DOOR NOT RESPONDING DTC SET
AUTOMATIC TEMPERATURE CONTROL (ATC)
OBSTRUCTED BLEND DOOR
PASSENGER BLEND DOOR ACTUATOR
TEST
ACTION
APPLICABILITY
1
Turn the ignition on.
With the DRBIII
t, read the active ATC DTCs.
Does the DRBIII
t display: PASSENGER BLEND DOOR NOT RESPONDING?
All
Yes
→ Return to the Heating & A/C symptom list and choose the
symptom.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Go To 2
2
Turn the ignition off.
Disconnect the Passenger Blend Door Actuator harness connector.
Connect a 12-volt Test Light between the Passenger Blend Door Actuator harness
connector cavities.
Turn the ignition on.
While monitoring the test light, press the PASSENGER BLEND mode switch to
change the temp setting from lo to hi.
NOTE: Observe test light for approximately 30 seconds.
Does the test light start to flash and stay flashing?
All
Yes
→ Go To 3
No
→ Replace the Automatic Temperature Control (ATC) in accordance
with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
602
HEATING & A/C
TEST
ACTION
APPLICABILITY
3
Remove the Passenger Blend Door Actuator from the A/C-Heater Housing assembly.
Rotate the passenger blend door from stop to stop. Note: The door should rotate
approximately 45 degrees from stop to stop.
Does the passenger blend door move smoothly in both directions?
All
Yes
→ Replace the Passenger Blend Door Actuator in accordance with
the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
No
→ Repair or replace the passenger blend door as necessary in
accordance with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
603
HEATING & A/C
PASSENGER BLEND DOOR TRAVEL TOO SMALL (ACTIVE) - ATC —
Continued
Symptom List:
PCI BUS SHORTED HIGH (ACTIVE) - ATC
PCI BUS SHORTED LOW (ACTIVE) - ATC
Test Note:
All symptoms listed above are diagnosed using the same tests.
The title for the tests will be PCI BUS SHORTED HIGH
(ACTIVE) - ATC.
When Monitored and Set Condition:
PCI BUS SHORTED HIGH (ACTIVE) - ATC
When Monitored:
With the ignition on and the IOD fuse installed.
Set Condition:
This DTC will set if the Automatic Temperature Control (ATC) detects a
short to voltage on the PCI Bus circuit.
PCI BUS SHORTED LOW (ACTIVE) - ATC
When Monitored:
With the ignition on and the IOD fuse installed.
Set Condition:
This DTC will set if the Automatic Temperature Control (ATC) detects a
short to ground on the PCI Bus circuit.
POSSIBLE CAUSES
AUTOMATIC TEMPERATURE CONTROL (ATC)
TEST
ACTION
APPLICABILITY
1
NOTE: For this DTC to be active, the DRBIII
t will not be able to communi-
cate with any modules on the vehicle except the Powertrain Control Module
(PCM).
NOTE: Do NOT perform this test unless this DTC is ACTIVE. If this DTC is
STORED, refer to PCI Bus Shorted High (Stored) or to PCI Bus Shorted Low
(Stored) in the HEATING & A/C symptom list.
View repair.
All
Repair
Replace the Automatic Temperature Control (ATC) in accordance
with the Service Information.
Perform BODY VERIFICATION TEST - VER 1.
604
HEATING & A/C
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст