Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 1124
7.
EXCESSIVE RESISTANCE IN THE (F856) 5–VOLT SUPPLY CIRCUIT
Measure the resistance of the (F856) 5-volt Supply circuit from the
Engine Oil Pressure Sensor harness connector to the appropriate ter-
minal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes
>> Go To 8
No
>> Repair the excessive resistance in the (F856) 5-volt Supply
circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to
9 - ENGINE - STANDARD PROCEDURE)
8.
(F856) 5-VOLT SUPPLY SHORTED TO GROUND
Measure the resistance between ground and the (F856) 5-volt Supply
circuit in the Engine Oil Pressure Sensor harness connector.
Is the resistance below 100 ohms?
Yes
>> Repair the short to ground in the (F856) 5-volt Supply cir-
cuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to
9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 9
9 - 520
ENGINE ELECTRICAL DIAGNOSTICS
LX
9.
EXCESSIVE RESISTANCE IN THE (K900) SENSOR GROUND CIRCUIT
Measure the resistance of the (K900) Sensor Ground circuit from the
Engine Oil Pressure Sensor harness connector to the appropriate ter-
minal of special tool #8815.
Is the resistance below 5.0 ohms?
Yes
>> Go To 10
No
>> Repair the excessive resistance in the (K900) Sensor
Ground circuit.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to
9 - ENGINE - STANDARD PROCEDURE)
10.
PCM
NOTE: Before continuing, check the PCM harness connector terminals for corrosion, damage, or terminal
push out. Repair as necessary.
Using the schematics as a guide, inspect the wire harness and connectors. Pay particular attention to all Power and
Ground circuits.
Were there any problems found?
Yes
>> Repair as necessary.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Replace and program the Powertrain Control Module per Service Information.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
LX
ENGINE ELECTRICAL DIAGNOSTICS
9 - 521
P0522-ENGINE OIL PRESSURE SENSOR CIRCUIT LOW
For a complete wiring diagram Refer to Section 8W.
9 - 522
ENGINE ELECTRICAL DIAGNOSTICS
LX
•
When Monitored:
With the ignition on. Battery voltage greater than 10 volts.
•
Set Condition:
The Oil pressure signal is below the calibrated amount. One Trip Fault. Three good trips to turn off the MIL.
ETC light will illuminate.
Possible Causes
(F856) 5-VOLT SUPPLY CIRCUIT OPEN
(F856) 5-VOLT SUPPLY CIRCUIT SHORTED TO GROUND
(G6) ENGINE OIL PRESSURE SIGNAL CIRCUIT SHORTED TO GROUND
(G6) ENGINE OIL PRESSURE SIGNAL CIRCUIT SHORTED TO THE (K900) SENSOR GROUND CIRCUIT
ENGINE OIL PRESSURE SENSOR
PCM
Always perform the Pre-Diagnostic Troubleshooting procedure before proceeding. (Refer to 9 - ENGINE -
DIAGNOSIS AND TESTING).
Diagnostic Test
1.
ACTIVE DTC
NOTE: Ensure that the engine oil is at the proper level. Also, check the customers oil change history to
ensure that the oil is being changed at the correct intervals and that the proper oil viscosity is being used.
Ignition on, engine not running.
With a scan tool, read DTCs.
Is the DTC active at this time?
Yes
>> Go To 2
No
>> Refer to the INTERMITTENT CONDITION Diagnostic Procedure.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
2.
(F856) 5-VOLT SUPPLY CIRCUIT
Turn the ignition off.
Disconnect the Engine Oil Pressure Sensor harness connector.
Ignition on, engine not running.
Measure the voltage on the (F856) 5-volt Supply circuit in the Engine Oil Pressure Sensor harness connector.
Is the voltage between 4.8 to 5.2 volts?
Yes
>> Go To 3
No
>> Go To 6
3.
ENGINE OIL PRESSURE SENSOR
With a scan tool, monitor the Engine Oil Pressure Sensor voltage with the Sensor harness connector disconnected.
Is the voltage above 4.5 volts?
Yes
>> Replace the Engine Oil Pressure Sensor.
Perform the POWERTRAIN VERIFICATION TEST. (Refer to 9 - ENGINE - STANDARD PROCEDURE)
No
>> Go To 4
LX
ENGINE ELECTRICAL DIAGNOSTICS
9 - 523
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст