Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 2346
refer to 23 - BODY/INSTRUMENT PANEL/CLUSTER BEZEL - REMOVAL and 23 - BODY/INSTRUMENT PANEL/
INSTRUMENT PANEL CENTER BEZEL - REMOVAL.
REMOVAL
AIR OUTLET - CHRYSLER
NOTE: Only the outboard instrument panel air outlets can be serviced separately. For service of the other
instrument panel air outlets refer to 23 - BODY/INSTRUMENT PANEL/INSTRUMENT PANEL CENTER BEZEL
- REMOVAL.
NOTE: LHD model shown. RHD model similar.
1. Using a trim stick or another suitable wide flat-
bladed tool (1), gently pry on both sides of the out-
board instrument panel air outlet(s) (2) until the air
outlet snap clip retainers are released from the
face of the instrument panel (3).
2. Gently slide the air outlet(s) rearward to release the
top of the outlet (demister outlet) from the instru-
ment panel.
AIR OUTLET - DODGE
NOTE: Only the outboard passenger side instrument panel air outlet can be serviced separately. For service
of the other instrument panel air outlets refer to 23 - BODY/INSTRUMENT PANEL/CLUSTER BEZEL -
REMOVAL and to 23 - BODY/INSTRUMENT PANEL/INSTRUMENT PANEL CENTER BEZEL - REMOVAL.
NOTE: LHD model shown in illustrations. RHD model similar.
1. Rotate the top of the outboard passenger side air
outlet barrel (1) downwards.
24 - 418
DISTRIBUTION
LX
2. Gently pull out on the bottom edge of the air outlet
(1) to release the snap clip retainers that secure
the outlet to the instrument panel (2).
3. Remove the air outlet from the instrument panel.
AIR OUTLET BARRELS - DODGE
NOTE: The instrument panel air outlet barrels are retained to the pivots within the air outlets by a snap fit.
NOTE: LHD model shown. RHD model similar.
1. Using a trim stick or another suitable wide flat-
bladed tool (1), gently pry the air outlet barrel(s) (2)
out of the instrument panel air outlet(s) (3) as
required.
LX
DISTRIBUTION
24 - 419
INSTALLATION
AIR OUTLET - CHRYSLER
NOTE: LHD model shown. RHD model similar.
1. Position the outboard air outlet (1) into its location
on the instrument panel (2).
NOTE: Make sure that the air outlet is properly
aligned to the duct within the instrument panel
opening and that the foam seal on the outlet is
properly installed.
2. Align the air outlet foam seal (3) with the duct in
the instrument panel (4) and slide the top portion of
the air outlet into the instrument panel top pad.
Gently push on the sides of the air outlet until the
snap clip retainers on the outlet are fully engaged
to the instrument panel.
AIR OUTLET - DODGE
NOTE: LHD model shown. RHD model similar.
1. Position the air outlet (1) into its location on the
outboard passenger side of the instrument panel
(2).
NOTE: Make sure that the air outlet is properly
aligned to the duct within the instrument panel
opening and that the foam seal on the outlet is
properly installed.
2. Align the air outlet foam seal (3) with the duct in
the instrument panel (4) and gently push on the air
outlet until the snap clip retainers on the outlet are
fully engaged to the instrument panel.
AIR OUTLET BARRELS - DODGE
NOTE: LHD model shown in illustration. RHD model similar.
24 - 420
DISTRIBUTION
LX
1. Install the air outlet barrel (1) onto the pivot shaft
(2) on the right side of the instrument panel air out-
let (3).
2. Gently push the air outlet barrel (1) onto the pivot
shaft (2) on the left side of the instrument panel air
outlet (3).
LX
DISTRIBUTION
24 - 421
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст