Chrysler 300/300 Touring/300C, Dodge Magnum. Manual — part 2337
8. Install the carpet onto the front floor panel and under the instrument panel (Refer to 23 - BODY/INTERIOR/
CARPETS AND FLOOR MATS - INSTALLATION).
9. Install the front seats (Refer to 23 - BODY/SEATS/SEAT - INSTALLATION).
10. Install the center floor console (Refer to 23 - BODY/INTERIOR/FLOOR CONSOLE - INSTALLATION).
24 - 382
DISTRIBUTION
LX
DUCT-INSTRUMENT PANEL
REMOVAL
WARNING: On vehicles equipped with airbags, disable the airbag system before attempting any steering
wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the
battery negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before
performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to
take the proper precautions could result in accidental airbag deployment and possible personal injury or
death.
NOTE: Take the proper precautions to protect the front face of the instrument panel from cosmetic damage.
NOTE: LHD model shown. RHD model similar.
1. Remove the instrument panel and place it on a
workbench (Refer to 23 - BODY/INSTRUMENT
PANEL/INSTRUMENT
PANEL
ASSEMBLY
-
REMOVAL).
2. Remove the screw that secures the instrument
panel top pad (1) to the reinforcement bracket (2).
3. Remove the four screws that secure the driver side
instrument panel duct and demister duct assembly
(3) to the instrument panel and remove the duct
assembly.
4. Remove the four screws that secure the passenger
side instrument panel duct and demister duct
assembly (4) to the instrument panel and remove
the duct assembly.
INSTALLATION
NOTE: LHD model shown. RHD model similar.
1. Position the passenger side instrument panel duct
and demister duct assembly (4) into the instrument
panel.
2. Install the passenger side instrument panel duct
and demister duct assembly onto the outlets of the
instrument panel. Make sure that the ducts are cor-
rectly installed over the instrument panel and
demister outlet seals.
3. Install the four screws that secure the passenger
side instrument panel duct and demister duct
assembly to the instrument panel. Tighten the
screws to 2.2 N·m (20 in. lbs.).
4. Position the driver side instrument panel duct and
demister duct assembly (3) into the instrument
panel.
5. Install the driver side instrument panel duct and
demister duct assembly onto the outlets of the instrument panel. Make sure that the ducts are correctly installed
over the instrument panel and demister outlet seals.
6. Install the four screws that secure the driver side instrument panel duct and demister duct assembly to the instru-
ment panel. Tighten the screws to 2.2 N·m (20 in. lbs.).
LX
DISTRIBUTION
24 - 383
7. Install the screw that secures the instrument panel top pad (1) to the reinforcement bracket (2). Tighten the
screw to 2.2 N·m (20 in. lbs.).
8. Install the instrument panel (Refer to 23 - BODY/INSTRUMENT PANEL/INSTRUMENT PANEL ASSEMBLY -
INSTALLATION).
24 - 384
DISTRIBUTION
LX
DUCT-INSTRUMENT PANEL DEMISTER
REMOVAL
WARNING: On vehicles equipped with airbags, disable the airbag system before attempting any steering
wheel, steering column, or instrument panel component diagnosis or service. Disconnect and isolate the
battery negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before
performing further diagnosis or service. This is the only sure way to disable the airbag system. Failure to
take the proper precautions could result in accidental airbag deployment and possible personal injury or
death.
NOTE: Take the proper precautions to protect the front face of the instrument panel from cosmetic damage.
NOTE: LHD model shown. RHD model similar.
1. Remove the instrument panel and place it on a
workbench (Refer to 23 - BODY/INSTRUMENT
PANEL/INSTRUMENT
PANEL
ASSEMBLY
-
REMOVAL).
2. Remove the screw that secures the instrument
panel top pad (1) to the reinforcement bracket (2).
3. Remove the four screws that secure the driver side
instrument panel duct and demister duct assembly
(3) to the instrument panel and remove the duct
assembly.
4. Remove the four screws that secure the passenger
side instrument panel duct and demister duct
assembly (4) to the instrument panel and remove
the duct assembly.
INSTALLATION
NOTE: LHD model shown. RHD model similar.
1. Position the passenger side instrument panel duct
and demister duct assembly (4) into the instrument
panel.
2. Install the passenger side instrument panel duct
and demister duct assembly onto the outlets of the
instrument panel. Make sure that the ducts are cor-
rectly installed over the instrument panel and
demister outlet seals.
3. Install the four screws that secure the passenger
side instrument panel duct and demister duct
assembly to the instrument panel. Tighten the
screws to 2.2 N·m (20 in. lbs.).
4. Position the driver side instrument panel duct and
demister duct assembly (3) into the instrument
panel.
5. Install the driver side instrument panel duct and
demister duct assembly onto the outlets of the instrument panel. Make sure that the ducts are correctly installed
over the instrument panel and demister outlet seals.
6. Install the four screws that secure the driver side instrument panel duct and demister duct assembly to the instru-
ment panel. Tighten the screws to 2.2 N·m (20 in. lbs.).
LX
DISTRIBUTION
24 - 385
Нет комментариевНе стесняйтесь поделиться с нами вашим ценным мнением.
Текст